Претраживање
Приказ резултата 31-40 од 73
On the Al-Mg alloy sheets for automotive application: Problems and solutions
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Aluminium alloys suitable for automotive application were reviewed briefly as well as the reasons for the future wider application of Al-Mg type alloys. Basic problems related to the limited consumption of Al-Mg type alloy ...
FEM modeling of dynamic recrystallization in 304 stainless steel
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Series of isothermal uniaxial compression tests in the temperature range (600-1100°C) with two strain rates of 0.1 and 1.0 s"1 were performed with the aim to obtain input data for the finite elements modeling (FEM) of ...
Characterization of wastewater streams from Bor site
(Savez inženjera metalurgije Srbije, Beograd, 2007)
This paper presents full characterization of wastewater streams within Bor copper mine. Seven different wastewater streams were identified and fully characterized (origin, flow rate, chemical and physical properties) on ...
Problems and prospect of Al-Mg alloys application in marine constructions
(Savez inženjera metalurgije Srbije, Beograd, 2006)
The position of steel as the most widely used material in the shipbuilding industry originates from the superior mechanical properties and low manufacturing costs The increasing demands for lowering the weight of different ...
The influence of titanium and cerium on microstructure and properties of Fe-C-Cr-Nb alloys / Uticaj titana i cerijuma na mikrostrukturu i svojstva Fe-C-Cr-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2005)
In this paper, the influence of titanium and cerium on the microstructure and properties of Fe-C-Cr-Nb alloys are examined, in both as-cast and heat treated state. These elements affect the crystallisation process of ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1. Investigations were performed on superalloy single crystals based Ni which were ...
Overview of the materials: Metals selection process / Strategija izbora metalnih materijala
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Overview of the metal material selection process will be subject of this paper. Interrelationship among design, materials and processing will be presented. Materials selection for a new design as well as materials substitution ...
Hydrometallurgical process for extraction of metals from electronic waste, part II: Development of the processes for the recovery of copper from printed circuit boards (PCB)
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Rapid technological development induces increase of generation of used electric and electronic equipment waste, causing a serious threat to the environment. Waste printed circuit boards (WPCBs), as the main component of ...
The influence of the interface shape on the plane-to-cellular-to-dendritic transition in superalloy based of nickel
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper investigation of the influence of the crystallization conditions on the interface shape during the solidification of Ni-based Superalloy by Vertical Bridgman method were investigated. The samples were undertaken ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...