Претраживање
Приказ резултата 21-30 од 149
Finite element analysis of fracture resistance parameters for stationary semi-elliptical surface cracks in high strength steel / Analiza parametara otpornosti na lom metodom konačnih elemenata, kod stacionarnih polueliptičnih prslina u čeliku povišene čvrstoće
(Society for Structural Integrity and Life, Institute for Material Testing, 2015)
This study deals with numerical simulations based on elastic-plastic finite element method for nonlinear stress analyses on pre-cracked tensile specimens with high strength properties. The influence of crack geometry on ...
The analysis of the tribological properties of multiple strengthened nanocomposite of the Cu-Al2o3 system
(Savez inženjera metalurgije Srbije, Beograd, 2011)
This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and ...
Modern steels: Transformation induced plasticity / Savremeni čelici - transformacijom izazvana plastičnost
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2011)
TRIP čelici danas zauzimaju značajno mesto u komercijaloj upotrebi u vozilima i konstrukcijama kod kojih je jedan od glavnih zahteva redukcija sopstvene težine. Optimalna kombinacija udela stabilisanog austenita i stepen ...
Quality assurance of storage tanks after in-service crack repairs / Osiguranje kvaliteta rezervoara u eksploataciji posle popravke prslina
(Society for Structural Integrity and Life, Institute for Material Testing, 2013)
According to the Pressure Equipment Directive (PED 97/23/EC) a new produced storage tank can be accepted on the market only if the required quality is proved. In this way the structural integrity might be at the requested ...
Antifungal activity of the basil (Ocimmum basilicum L.) extract on Penicillium aurantiogriseum, P. glabrum, P. chrysogenum, and P. brevicompactum / Antifungalna aktivnost ekstrakta bosiljka (Ocimmum basilicum L.) na rast Penicillium aurantiogriseum, P. glabrum, P. chrysogenum i P. brevicompactum
(Faculty of Technology, Novi Sad, 2012)
This study was aimed at investigating the antifungal potential of basil (Ocimmum basilicum L.) extract against toxin-producing Penicillium spp. (P. aurantiogriseum, P. glabrum, P. chrysogenum, and P. brevicompactum) isolated ...
Assessment of the integrity of welded pipes / Procena integriteta zavarenih cevi
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The subject of the paper is analysis of the integrity of welded pipes made of API J55 steel by high frequency contact welding (HF). Experimental research on the mechanical properties of the base material was conducted on ...
Microstructural characterization of glass-epoxy composites subjected to tensile testing / Mikromehanička karakterizacija staklo-epoksi kompozita izloženog zateznom opterećenju
(Faculty of Technology, Novi Sad, 2013)
The main objective of the research presented in this paper was to carry out a statistical-mechanical analysis concerning the tensile test of glass-epoxy composite materials in order to calculate their relevant tension ...
Treatment of waste sulfuric acid copper electrolyte / Tretman otpadnog sumporno-kiselog elektrolita bakra
(Institut za rudarstvo i metalurgiju, Bor, 2014)
The aim of this paper was to investigate the possibility of using the copper anodes with high nickel content for electrolytic treatment of waste sulfuric acid copper electrolyte. Nickel content in each anode was about 10 ...
Application of exergy analysis in recycling streams / Primena eksergijske analize u reciklažnim tokovima
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
Materials for recycling always contain a certain degree of contamination. The presence of impurities i.e. contamination in the recycling streams causes a change in the composition of the original materials to recycle. As ...
Examination of wear resistance of polymer-basalt composites
(Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac, 2013)
Olivine basalt, as a natural material, has excellent physical and mechanical properties such as hardness, compressive strength, wear resistance, color and gloss. On the other hand it is difficult for processing, because ...