Претраживање
Приказ резултата 11-20 од 38
Cross-section analysis of the morphology of electrodeposited copper obtained in the hydrogen co-deposition range / Morfologija poprečnog preseka prevlaka bakra dobijenih elektrohemijskim taloženjem u oblasti ko-depozicije vodonika
(Serbian Chemical Society, 2009)
Cross-section analysis of copper deposits electrodeposited in the hydrogen co-deposition range at a constant overpotential and in a pulsating overpotential (PO) regime was performed. It was shown that a complete structural ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Engineering Society for Corrosion, Belgrade, Serbia, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
Microstructure and corrosion behaviour of Zn-Co alloys deposited from three different plating baths / Mikrostruktura i koroziono ponašanje Zn-Co legura taloženih iz sulfatnog i hloridnih rastvora
(Serbian Chemical Society, Belgrade, 2011)
The effects of plating baths of different composition on the micro- structure and corrosion stability of Zn-Co alloy coatings were studied. Zn-Co alloys with the same Co content were deposited from chloride plating baths ...
Formation of Disperse Silver Deposits by the Electrodeposition Processes at High Overpotentials
(Esg, Belgrade, 2012)
In this study, electrodeposition of silver from nitrate solution at the high overpotentials was analyzed. Morphologies of silver deposits obtained at the different overpotentials and with the different electrodeposition ...
Electrochemical deposition and characterization of Zn-Fe alloys / Elektrohemijsko taloženje i karakterizacija Zn-Fe legura
(Serbian Chemical Society, Belgrade, 2004)
Zn–Fe alloy electrochemically deposited on steel under various deposition conditions were investigated using anodic linear sweep voltammetry (ALSV) and X-ray diffraction (XRD) analysis for phase structure determination, ...
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
The study of Zn-Co alloy coatings electrochemically deposited by pulse current / Ispitivanje prevlaka Zn-Co legura dobijenih pulsirajućom strujom
(Association of Chemical Engineers of Serbia, 2012)
The electrochemical deposition by pulse current of Zn-Co alloy coatings on steel was examined, with the aim to find out whether pulse plating could produce alloys that could offer a better corrosion protection. The influence ...
Ceria Particles as Efficient Dopant in the Electrodeposition of Zn-Co-CeO2 Composite Coatings with Enhanced Corrosion Resistance: The Effect of Current Density and Particle Concentration
(Molecules, 2021)
Novel Zn-Co-CeO2 protective composite coatings were deposited successfully from chloride plating solutions. Two different types of ceria sources were used and compared: commercial ceria powder and home-made ceria sol. ...
Effect of temperature on the electrodeposition of disperse copper deposits / Uticaj temperature na elektrohemijsko taloženje disperznih taloga bakra
(Serbian Chemical Society, 2007)
The effect of temperature on the electrodeposition of copper at overpotentials belonging to the plateau of the limiting diffusion current density and higher was examined by the determination of the average current efficiency ...
Synergetic effect of additives on the hardness and adhesion of thin electrodeposited copper films
(Faculty of Technical Sciences in Cacak, 2017)
Thin copper films were electrodeposited on a polycrystalline cold rolled copper substrate. The composition of the laboratory-made copper sulphate electrolyte was changed by the addition of various additives. The influence ...