Претраживање
Приказ резултата 21-30 од 43
Characterization of MgAl2O4 Sintered Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Single phase MgAl2O4 was made from a one-to-one molar ratio of MgO and Al2O3 powders mixed using ball-milling. Mixtures of MgO and Al2O3 were subsequently treated in planetary ball mill for 30, 60, 90 and 120 minutes in ...
Anisotropy Analysis of Low Cement Concrete by Ultrasonic Measurements and Image Analysis
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
The analized material was high alumina low cement castable sintered at three different temperatures. Influence of initial material anisotropy on the thermal shock resistance as well as changes of anisotropy level during ...
Photocatalytic Degradation of Bisphenol A with alpha-Fe2O3 Fibers and Particles
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Two-step synthesis of Fe2O3 particles, performed by precipitation from iron(III) chloride (FeCl3 center dot 6H(2)O) using ammonium hydroxide in first step and calcination at 400 and 700 degrees C during 4 h, provided Fe2O3 ...
Impact of Alumina Particles on the Morphology and Mechanics of Hybrid Wood Plastic Composite Materials
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Hybrid composite panels of Wood-Plastic Composites (WPC) consisting of wood and poly (methyl methacrylate) (PMMA) were reinforced with alumina particles and made by "hot pressing" method. Alumina-based particles were made ...
The Influence of Powder Particle Size on Properties of Cu-Al2O3 Composites
(International Institute for the Science of Sintering (IISS), 2009)
Inert gas atomized prealloyed copper powder containing 2 wt.% Al (average particle size approximate to 30 mu m) and a mixture consisting of copper (average particle sizes approximate to 15 mu m and 30 mu m) and 4 wt.% of ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
Preparation and Characterization of Novel Glycidyl Methacrylate/Clay Nanocomposites
(Science of SinteringScience of Sintering, 2022)
The impact of the type and amounts of nanofiller on the features of the glycidyl methacrylate-co-ethylene glycol dimethacrylate (GMA-co-EGDMA)/organomodified montmorillonite (OMt) nanocomposites that were prepared by in ...
Evaluation of Adsorption Performance and Quantum Chemical Modeling of Pesticides Removal using Cell-MG Hybrid Adsorbent
(Science of Sintering, 2021)
Magnetite (MG) modified cellulose membrane (Cell-MG), obtained by reaction of 3-aminosilane and subsequently with diethylenetriaminepentaacetic acid dianhydride functionalized waste Cell fibers (Cell-NH2 and Cell-DTPA, ...
Novel Method for Measurement of Pipeline Materials Fracture Resistance-Examination on Selective Laser Sintered Cylindrical Specimens
(International Institute for the Science of Sintering (IISS), 2022)
This paper presents a part of development of a non-standard method for testing of cylindrical test specimens for measurement of fracture properties of pipeline materials. This method for testing of cylindrical structures ...
An Experimental Study of Mechanical Properties and Heat Transfer of Acrylic Composites with Structural and Surface Modified Al2O3 Particles
(International Institute for the Science of Sintering (IISS), 2020)
Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat ...