Претраживање
Приказ резултата 31-40 од 58
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
Procedures for processing of copper secondary raw materials / Postupci prerade sekundarnih sirovina bakra
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
The technological procedures for copper secondary raw materials processing include two basic stages: pretreatment of the copper waste and its further metallurgical processing. For copper waste pretreatment technology, there ...
Application of exergy analysis in recycling streams / Primena eksergijske analize u reciklažnim tokovima
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
Materials for recycling always contain a certain degree of contamination. The presence of impurities i.e. contamination in the recycling streams causes a change in the composition of the original materials to recycle. As ...
Assessment of the integrity of welded pipes / Procena integriteta zavarenih cevi
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The subject of the paper is analysis of the integrity of welded pipes made of API J55 steel by high frequency contact welding (HF). Experimental research on the mechanical properties of the base material was conducted on ...
Characterization of oxide coatings formed by plasma electrolytic oxidation of aluminum in sodium tungstate / Karakterizacija oksidnih slojeva dobijenih plazma elektrolitičkom oksidacijom aluminijuma u natrijum volframatu
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
This paper presents our recent research on morphology and phase composition of oxide coatings formed by plasma electrolytic oxidation of aluminum in 0.1 M sodium tungstate at constant current density of 15 mA/cm2 and ...
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
Time: Temperature superposition principle: Application of WLF equation in polymer analysis and composites / Princip superponiranja vremena i temperature - primena WLF jednačine za ispitivanje polimera i kompozita
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Polymers are the most studied viscoelastic material. The shorter times (high frequencies) corresponding to lower temperatures and long times (low frequencies) to high temperatures. This represents the quantitatively applied ...
Influence of the structural changes on cavitation resistance of Al18SiCuMg alloy produced by rheocasting process / Uticaj strukturnih promena na kavitacionu otpornost Al18SiCuMg legure proizvedene reokasting procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The influence of stirring speeds of 1000 and 1500 r/min on the microstructure of Al18SiCuMg alloy was investigated. The smaller size of Si particles of rheocast sample obtained by higher cooling rate and higher stirring ...
Impedance characteristics of aluminum with sol-gel ceria protective coating during the exposure to chloride corrosion agent / Impedansni odgovor aluminijuma sa zaštitnom prevlakom oksida cerijuma tokom izlaganja hloridnoj korozionoj sredini
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Electrochemical impedance characteristics of bare Al and Al with CeO2 coating prepared sol-gel procedure from the ceria sol are investigated. The corrosion behavior is monitored during the exposure to 3 wt. % NaCl aqueous ...