Претраживање
Приказ резултата 71-80 од 168
Influence of the fabrication process of copper matrix composites on cavitation erosion resistance
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations ...
Some aspects of physical metallurgy of microalloyed steels
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Some aspects of deformation, precipitation, and recrystallization behavior in medium carbon V-microalloyed and low carbon Nb/Ti-microalloyed steels are presented in the paper. Changes in microstructure are explained together ...
Impedance characteristics of aluminum with sol-gel ceria protective coating during the exposure to chloride corrosion agent / Impedansni odgovor aluminijuma sa zaštitnom prevlakom oksida cerijuma tokom izlaganja hloridnoj korozionoj sredini
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Electrochemical impedance characteristics of bare Al and Al with CeO2 coating prepared sol-gel procedure from the ceria sol are investigated. The corrosion behavior is monitored during the exposure to 3 wt. % NaCl aqueous ...
Synthesis of 4,6-dimethyl-3-cyano-2-pyridone catalysed by amino acids / Sinteza 4,6-dimetil-3-cijano-2-piridona katalizovana aminokiselinama
(Engineering Society for Corrosion, Belgrade, Serbia, 2017)
In this work the synthesis of 4,6-dimethyl-3-cyano-2-pyridone catalyzed by amino acids was studied. In the first part of the work, the optimization was carried out by varying the initial concentration of glycine, the molar ...
Significance and applicability of structural integrity assessment / Značaj i primenljivost ocene integriteta konstrukcija
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
To avoid unexpected and frequent serious failures of objects and equipment in service, and save their structural integrity, proper experimental and theoretical analyses are required, that are supported by modeling and ...
Preservation of vitamin C, lycopene and carbohydrate content in tomato dried in a tunnel type dryer / Očuvanje vitamina C, likopena i ugljenih hidrata u plodovima paradajza sušenim u tunelskom tipu sušara
(Institute for Food Technology, Novi Sad, 2017)
The aim of this study was to find an optimal way of tomato drying in a tunnel type dryer, in order to achieve the lowest possible losses in nutritive value of dried tomato products. Domestic variety of tomato (SP-109) was ...
Leakage of an austenitic steel CO2 storage tank / Curenje posude za skladištenje CO2 od austenitnog čelika
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
After the occurrence of water droplets on the manhole outer wall of a storage tank for carbon dioxide, by detailed inspection, a net of cracks is detected in the manhole flange, close to the welded joint between the flange ...
Photocatalytic degradation of carbamate insecticides: Effect of different parameters / Fotokatalitička degradacija karbamatnih insekticida - efekti različitih parametara
(Institute of Pesticides and Environmental Protection, 2019)
Photocatalytic degradation of a model compound of the carbamate insecticide carbofuran in water was studied using polychromatic light and ZnO and TiO2 catalysts. The influence of operational parameters, such as reaction ...
Micromechanical crack analysis of glass-epoxy laminated composites subjected to tension load / Mikromehanička analiza loma laminatnog staklo-epoksi kompozitnog materijala ispitivanog na zatezanje
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The main objective of this study is to determine tensile properties of the glass-epoxy polymer composite material. The material is glass fiber 280 g/m², 'twill woven' with 100 cm width, type - Interglas 92125, and epoxy ...
Estimation of phosphorus distribution ratio at the end of blowing in bof
(Metallurgical & Materials Engineering, 2021)
In integrated steel plants, the removal of phosphorous normally takes place during the primary basic oxygen furnace (BOF) steelmaking process. Phosphorous is usually introduced to the integrated steelmaking process through ...