Претраживање
Приказ резултата 21-30 од 32
The effect of calcinated hydroxyapatite and magnesium doped hydroxyapatite as fillers on the mechanical properties of a model bisgma/tegdma dental composite initially and after aging
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This study aimed to investigate the possibility of modifying model BisGMA/TEGDMA dental composite by substituting 10 wt. % of conventional glass fillers with bioactive fillers based on calcinated nanosized hydroxyapatite ...
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys
(Savez inženjera metalurgije Srbije, Beograd, 2019)
The occurrence of abnormal grain growth (AGG) in AA5182 alloy during annealing imposes severe restrictions on processing parameters and deteriorates mechanical properties. In this work, we investigated the effect of chemical ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
Treatment of dispersed iron-bearing raw materials and modeling of the protection systems against air-pollution
(Association of Metallurgical Engineers of Serbia, 2016)
Based on the analysis of the non-standard iron-bearing raw materials treatment process and the results of real composition measurements of the flue gas, the study of hazards by identification of harmful substances that ...
Laboratory testing results of kinetics and processing technology of the polymetallic sulphide concentrate Blagojev Kamen - Serbia
(Association of Metallurgical Engineers of Serbia, 2016)
This work presents the laboratory testing results of kinetics the oxidation process and sample processing of the sulphide polymetallic concentrate Blagojev Kamen. The aim of investigation is recovery of these types of raw ...
Defect formation during synthesis and welding of silver nanowires for solar cell applications
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Structural defects such as stacking faults and twins, observed in many face-centered cubic (FCC) structured metals and alloys with low stacking fault energies, in general, play an important role in microstructure evolution, ...
A model for cross-referencing and calculating similarity of metal alloys
(Association of Metallurgical Engineers of Serbia, 2013)
This paper presents an innovative model for the comparison and cross- referencing of metal alloys, in order to determine their interchangeability in engineering, manufacturing and material sourcing. The model uses a large ...
Influence of the fabrication process of copper matrix composites on cavitation erosion resistance
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations ...
Integrated procedure for recycling and valorization of useful components from secondary raw materials based on hard metals
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Wide application of hard metals requires increased consumption of their constituents. Their high cost and scarcity impose the need for finding new, both ecologically and economically justified ways for their production. ...