Претраживање
Приказ резултата 31-40 од 73
Shot-peening induced twinning in ship-building steel / Dvojnikovanje u brodskom limu kao posledica tretiranja u mlazu sačme
(Savez inženjera metalurgije Srbije, Beograd, 2002)
The aim of this work to simulate a shot-peening process and reveal the final microstructure. The latter consisted of rafinated ferritic grains, with occurrence of twins in some grains. Since the twinning occurs when a very ...
Thermodynamic and structural investigation of the Ag-In-Sb system
(Croatian Metallurgical Society, 2007)
The Ag-In-Sb ternary system presents one of the possible lead-free solder candidates. Therefore, the results of thermodynamic study of the alloys in the Ag-In-Sb alloys, obtained using general solution mode!, are presented ...
Experimental design approach regarding kinetics of high pressure leaching processes / Dizajniranje eksperimenata u pogledu na kinetiku luženja pri visokim pritiscima
(Savez inženjera metalurgije Srbije, Beograd, 2003)
Kinetics of high pressure leaching of nickel latente ore "Rudjinci", Serbia was studied in this work. The following parameters: temperature, acid to ore ratio, stirring speed, and time were optimized in order to obtain the ...
Approximation of material behaviour of PLLA polymer in HAp/PLLA biocomposite material using nanoindentation and finite element method
(Savez inženjera metalurgije Srbije, Beograd, 2007)
In this work, a combination of nanoindentation experiment and finite element modeling is proposed in order to obtain approximate material behavior of PLLA polymer in hydroxyapatite (HAp)/poly-L-lactide (PLLA) composite. ...
Rotating disk alumina precursor fiber formation process stability determination using image analysis
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Precursor fibers are made from the aluminium-hydroxide chloride based sols. The process stability can be influenced both by the fiber formation conditions and the rheology of the sol. The distance from the disk canter is ...
The effect of mould temperature and cooling conditions on the size of secondary dendrite arm spacing in Al-7Si-3Cu alloy
(Savez inženjera metalurgije Srbije, Beograd, 2009)
The secondary dendrite arm spacing (SDAS) is one of the most important microstructure features of as-cast structure in hypoeutectic aluminum alloys. The size of SDAS depends on many factors such as liquid metal treatment, ...
Influence of Cr, Mn and Mo on structure and properties of V microalloyed medium carbon forging steels
(Savez inženjera metalurgije Srbije, Beograd, 2010)
The influence of Cr, Mo and Mn on microstructure and mechanical properties of V-microalloyed medium-carbon steels has been studied by means of metallography and mechanical testing. Cr, Mn and Mo addition promotes the ...
Effect of heating rate on precipitation of peak-aged Al-Li (8091) alloy: A quantitative approach
(Savez inženjera metalurgije Srbije, Beograd, 2010)
Samples of Al-Li (8091) alloy were solution treated at 540ºC for 30 min, water-quenched and continuously heated in oil at 0.05 and 0.1ºC/min rates, from room temperature to 190ºC when the peak hardness was achieved. Having ...
The effects of thermomechanical treatment on the SCC resistance of highly alloyed Al-Mg sheet / Uticaj termomehaničke obrade na otpornost prema naponskoj koroziji visoko legiranih Al-Mg limova
(Savez inženjera metalurgije Srbije, Beograd, 2002)
The effects of cold work and different heat treatments on the stress corrosion cracking (SCC) behavior of Al-Mg6.8% alloy were studied using slow strain rate testing (SSRT). The results have indicated high SCC susceptibility ...
Structure and kinetics of internal oxidation in Ag-Sn alloys / Struktura i kinetika interne oksidacije Ag-Sn legura
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Internal oxidation in Ag-Sn-In-Te and Ag-Sn-Cu-Bi alloys was tested. micro structures of casted and homogenized samples, as well as after internal oxidation were followed by optical microscopy. The structure of Ag-Sn-Cu-Bi ...