Претраживање
Приказ резултата 11-20 од 72
The analysis of the tribological properties of multiple strengthened nanocomposite of the Cu-Al2o3 system
(Savez inženjera metalurgije Srbije, Beograd, 2011)
This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and ...
Specific energy absorption capacity of glass-polyester composite tubes under static compressive loading
(Croatian Metallurgical Society, 2011)
The experimental determination of energy of glass-polyester composite tubes static fracture is done. The tubes are of defined structure and known processes of fabrication. The aim was to determine the possibility of their ...
Structural properties of Co, Ni and Mo powders obtained by electrochemical deposition
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Magnetic thin films based on iron group elements (Fe, Co, Ni) are currently used in computer's hard disk drives and in MEMS, whereas electrodeposition is a suitable method to obtain these materials. The powders of metals ...
Determination of activation energy for static recrystallization using multipass continuous cooling torsion test
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Two microalloyed steels (Nb low carbon and V medium carbon) were tested by means of multistage continuous cooling torsion with aim to evaluate the interpass recrystallization data, by means of Tnr (temperature of ...
The effect of heat treatment on toughness and wear resistance of Fe-Cr-C-Nb alloys / Uticaj termičke obrade na žilavost i otpornost na habanje Fe-Cr-C-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Alloying with niobium improves the mechanical properties of the high chromium irons. The alloy containing appriximately 3 %Nb gives the best compromise between wear resistance and toughness. These properties were improved ...
Microstructure evolution of the hot-rolled modified AA 5083 alloys during the two stage thermal treatment
(Savez inženjera metalurgije Srbije, Beograd, 2011)
The effects of the two stage heat treatment on the structure of two hot-rolled 5083 aluminum alloys without and with 0.12% Zr addition were investigated. Combination of the metallographic and transmission electron microscopy ...
Development of contemporary procedures for lead obtaining / Razvoj savremenih postupaka dobijanja olova
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Contemporary procedures of lead concentrates treatment were in different expansion during last thirty years. All procedures have in common the following: smelting reaction proceeds in solid-gas suspension, melting products ...
Dynamic recrystallization in M2 tool steel during friction welding
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Friction welding of M2 tool steel and 1730 quenched and tempered steel was performed with the aim to reveal the origin of extremely fine martensitic grain in M2 steel after welding. Taking into account thermomechanical ...
Hydrometallurgical recovery of tin and lead from waste printed circuit boards (wpcbs): limitations and opportunities
(Croatian Metallurgical Soc, Zagreb, 2016)
In this paper, possibility for selective Pb and Sn recovery, using three different solutions of NaOH, HCl and HNO3, from WPCBs containing low concentrations of Pb and Sn is presented. According to obtained results, over ...
Influence of milling parameters on the preparation of fine tungsten and copper powders by mechanically induced self-propagating reaction / Uticaj parametara mlevenja na dobijanje finih prahova volframa i bakra mehanički iniciranom samorasprostirućom reakcijom
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Mechanically induced self-propagating reaction in planetary ball mill was realized in three different systems, CaWO4 (scheelite) + Mg, CuO + Ti and CuO + Zr. An influence of a ball diameter (from 5 to 41.2 mm) at three ...