Претраживање
Приказ резултата 21-30 од 72
A two-stage metal valorisation process from electric arc furnace dust (eafd)
(Croatian Metallurgical Soc, Zagreb, 2016)
This paper demonstrates possibility of separate zinc and lead recovery from coal composite pellets, composed of EAFD with other synergetic iron-bearing wastes and by-products (mill scale, pyrite-cinder, magnetite concentrate), ...
Investigation of mechanism and kinetics of chalcopyrite concentrate oxidation process
(Croatian Metallurgical Society, 2008)
The oxidation process of chalcopyrite concentrate "Rudnik" (Serbia) was investigated by DTA-TG measurements under air conditions in the temperature range of 298 - 1173 K, as well as by XRD analysis of the oxidation products ...
Synthesis and sintering of Cu-Al2O3 nanocomposite powders produced by a thermochemical route
(Savez inženjera metalurgije Srbije, Beograd, 2007)
By hydrometallurgy and powder metallurgy along with prognosis of physical-chemical properties, a synthesis of new improved materials can be successfully performed with in advance pre-set properties which is conditioned by ...
The recycling of high magnesium aluminum alloys estimation of the most reliable procedure
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Aluminum is one of the most recyclable materials. Namely, the properties of aluminum are not affected by the recycling and reuse, thus enable that high value of the metal is maintained after reprocessing. The re-smelting ...
Determination of AL2O3particle size in Cu-AL2O3 nanocomposite materials using UV spectrophotometry / Određivanje veličine čestica AL2O3 u nanokompozitnim materijalima iz sistema Cu-AL2O3 primenom UV spektrofotometrije
(Savez inženjera metalurgije Srbije, Beograd, 2008)
In order to achieve improved mechanical properties of dispersion strengthened nanocomposite, without influencing electrical and thermal conductivity it is necessary for dispersoide to be nano sized and uniformly distributed ...
Characterization of nano-powder morphology obtained by ultrasonic spray pyrolysis
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Spherical nanosized particles of copper were synthesized by ultrasonic dispersion of solutions from copper sulphate in the temperature range of 800-900°C in hydrogen atmosphere. A controlled particle size was realized ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1. Investigations were performed on superalloy single crystals based Ni which were ...
The influence of the solidification rate on the interface shape and distribution of solute
(Savez inženjera metalurgije Srbije, Beograd, 2002)
In this paper investigation of the influence of the solidification conditions on the interface shape and distribution of solute during the solidification of AI-Cu alloy by vertical Bridgman method were investigated. The ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...