Претраживање
Приказ резултата 41-50 од 72
The effect of mould temperature and cooling conditions on the size of secondary dendrite arm spacing in Al-7Si-3Cu alloy
(Savez inženjera metalurgije Srbije, Beograd, 2009)
The secondary dendrite arm spacing (SDAS) is one of the most important microstructure features of as-cast structure in hypoeutectic aluminum alloys. The size of SDAS depends on many factors such as liquid metal treatment, ...
Monitoring the damage level during thermal stability testing of refractory sample using soninic measurement
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Thermal stability of the refractory material with the content of 28 % AI2O3 was investigated. Water quench test (JUS.B.D8.319.) was applied as experimental method for thermal stability testing. Dynamic Young modulus of ...
Studies of a wear resistant cast iron / Izučavanje belih gvožđa otpornih na habanje
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The objective of this investigation was to set down (on the base of the results obtained by the examination of white cast iron alloys with different content of the alloying elements) a correlation between chemical composition ...
Determination of activation energy for static recrystallization using multipass continuous cooling torsion test
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Two microalloyed steels (Nb low carbon and V medium carbon) were tested by means of multistage continuous cooling torsion with aim to evaluate the interpass recrystallization data, by means of Tnr (temperature of ...
The analysis of the tribological properties of multiple strengthened nanocomposite of the Cu-Al2o3 system
(Savez inženjera metalurgije Srbije, Beograd, 2011)
This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and ...
Structural properties of Co, Ni and Mo powders obtained by electrochemical deposition
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Magnetic thin films based on iron group elements (Fe, Co, Ni) are currently used in computer's hard disk drives and in MEMS, whereas electrodeposition is a suitable method to obtain these materials. The powders of metals ...
Specific energy absorption capacity of glass-polyester composite tubes under static compressive loading
(Croatian Metallurgical Society, 2011)
The experimental determination of energy of glass-polyester composite tubes static fracture is done. The tubes are of defined structure and known processes of fabrication. The aim was to determine the possibility of their ...
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheet
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheets was examined after cold rolling and annealing in the range of temperature from 220°C to 520°C, water quenching and natural aging. The low temperature annealed ...
Microstructural investigation of the heat-affected zone of simulated welded joint of p91 steel
(Croatian Metallurgical Society, 2013)
In the process of testing teal components exposed to elevated temperature, it is hot possible to neglect Cracks. The most significant cracks can be induced by welding, which is applied for joining of Structural components. ...
Structural characteristics of some ternary Ag-In-Sn alloys
(Savez inženjera metalurgije Srbije, Beograd, 2008)
The Ag-In-Sn system, as one of potential lead-free solder materials, was studied in this paper. The investigated alloys were chosen from two sections, with molar ratio of In:Sn equal to 1:4; 1:2. DTA, XRD, SEM and micro ...