Претраживање
Приказ резултата 51-60 од 73
Dependence of the solid-liquid interface structure on the solidification process parameters / Zavisnost strukture granice faza tečno-čvrsto od parametara procesa očvršćavanja
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Influence of the solidification rate, temperature gradient and initial concentration of the solute on the interface shape was investigated during solidification from the melt. The dependence of the microstructure on the ...
Image analysis of protective layer of zinc on steel obtained using the hot process / Analiza slike za karakterisanje zaštitnog sloja cinka na čeliku dobijenog toplim cinkovanjem
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The procedure for measuring the thickness of anticorrosion protective layer of zinc on steel is given. The metallographic images are used for this measurement. Results are statistically handled and results are used to ...
Influence of heat transfer conditions on determination of thermal shock resistance of refractories / Uticaj prenosa toplote na određivanje termostabilnosti vatrostalnog materijala
(Savez inženjera metalurgije Srbije, Beograd, 2002)
The goal of this thesis was to determine the thermal shock resistance of alumina based refractories in the case of a heat transfer conditions different from the standard conditions given by quenching test JUS. B. D.8 319. ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1 Investigations were performed on superalloy single crystals based Ni which were ...
On the Al-Mg alloy sheets for automotive application: Problems and solutions
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Aluminium alloys suitable for automotive application were reviewed briefly as well as the reasons for the future wider application of Al-Mg type alloys. Basic problems related to the limited consumption of Al-Mg type alloy ...
Hydrometallurgical process for extraction of metals from electronic waste, part II: Development of the processes for the recovery of copper from printed circuit boards (PCB)
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Rapid technological development induces increase of generation of used electric and electronic equipment waste, causing a serious threat to the environment. Waste printed circuit boards (WPCBs), as the main component of ...
The influence of the interface shape on the plane-to-cellular-to-dendritic transition in superalloy based of nickel
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper investigation of the influence of the crystallization conditions on the interface shape during the solidification of Ni-based Superalloy by Vertical Bridgman method were investigated. The samples were undertaken ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
Overview of the materials: Metals selection process / Strategija izbora metalnih materijala
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Overview of the metal material selection process will be subject of this paper. Interrelationship among design, materials and processing will be presented. Materials selection for a new design as well as materials substitution ...