Pretraživanje
Prikaz rezultata 11-20 od 73
Kinetics of crystallization silicon-(IV)-nitride / Kinetika kristalizacije silicijum-(IV)-nitrida
(Savez inženjera metalurgije Srbije, Beograd, 2003)
Amorphous covalent Si-C-N ceramics have been synthesized by pyrolysis polysilazanes. This part of experiment was done in Institute für Nichtmetallische Anorganische Materialien, Universitaet Stuttgart, Germany. Ceramics ...
Development of a collision energy absorber of a passenger train
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Development of shock absorbers is one of the necessary measures for passive protection of passenger coaches. The purpose of passive protection is to minimize the collision consequences for passengers. Present solutions are ...
Problems and prospect of Al-Mg alloys application in marine constructions
(Savez inženjera metalurgije Srbije, Beograd, 2006)
The position of steel as the most widely used material in the shipbuilding industry originates from the superior mechanical properties and low manufacturing costs The increasing demands for lowering the weight of different ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1 Investigations were performed on superalloy single crystals based Ni which were ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Application of instrumental methods in the investigation of properties and microstructure of construction concretes / Primena instrumentalnih metoda za ispitivanje svojstava i mikrostrukture konstukcionih betona
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Methods for the investigation of microstructure of construction concretes are presented in this paper. Concrete is a composite material, thus its microstructure consists of bonding agent (cement) and aggregate with predefined ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
Studies of a wear resistant cast iron / Izučavanje belih gvožđa otpornih na habanje
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The objective of this investigation was to set down (on the base of the results obtained by the examination of white cast iron alloys with different content of the alloying elements) a correlation between chemical composition ...
Approximation of material behaviour of PLLA polymer in HAp/PLLA biocomposite material using nanoindentation and finite element method
(Savez inženjera metalurgije Srbije, Beograd, 2007)
In this work, a combination of nanoindentation experiment and finite element modeling is proposed in order to obtain approximate material behavior of PLLA polymer in hydroxyapatite (HAp)/poly-L-lactide (PLLA) composite. ...
Rotating disk alumina precursor fiber formation process stability determination using image analysis
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Precursor fibers are made from the aluminium-hydroxide chloride based sols. The process stability can be influenced both by the fiber formation conditions and the rheology of the sol. The distance from the disk canter is ...