Претраживање
Приказ резултата 31-40 од 42
The Influence of Barium Ferrite Nanoparticles on Morphological and Mechanical Properties of Ethyl Cellulose Based Nanocomposites
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
This study presents preparation and characterization of ethyl cellulose based nanocomposites. Successful use of simple solvent casting technique provided nanocomposites with high loads of barium ferrite magnetic nanopowder ...
Influence of Temperature and Different Hydroxides on Properties of Activated Carbon Prepared From Saccharose. Characterization, Thermal Degradation Kinetic and Dyes Removal From Water Solutions
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
In presented paper, influence of temperature, precursor concentration and different hydroxides on properties of activated carbon obtained from saccharose were investigated. The samples were prepared by hydrothermal treatment ...
Improving the Packaging Performance of Low-Density Polyethylene With PCL/Nanocellulose/Copper(II)Oxide Barrier Layer
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
A novel double layered hybrid materials, consisting of low density polyethylene (LDPE) base layer and polycaprolactone (PCL) top layer containing surface modified nanocellulose (NC) based nanocomposites in 0.5 and 2% ...
Characterization of Neodymium Doped Calcium Tungstate Single Crystal by Raman, IR and Luminescence Spectroscopy
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
The aim of the current work was to assess obtain a single crystal of calcium tungstate doped with neodymium - (CaWO4:Nd3+), and after that, the crystal was characterized with various spectroscopic methods. The single crystal ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
Solid state synthesis of extra phase-pure Li4Ti5O12 spinel
(Belgrade : International Institute for the Science of Sintering, 2011)
Extra phase-pure Li4Ti5O12 spinel with particle sizes less than 500 nm was synthesized by solid state reaction of mechanochemicaly activated mixture of nano anatase and Li2CO3 for a very short annealing time, 4 h at 800°C. ...
The Mechanisms of Cavitation Erosion of Raw and Sintered Basalt
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
The paper analyzes the morphology of cavitation damage of raw and sintered basalt samples. The experiment was conducted using the ultrasonic vibratory cavitation test method according to the ASTM G-32 standard. During the ...
Properties of Zig-Zag Nickel Nanostructures Obtained by GLAD Technique
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
Zig-zag structure of the nickel thin film has been obtained using Glancing Angle Deposition (GLAD) technique. Glass substrate was positioned 75 degrees with respect to the substrate normal. The obtained nickel thin film ...
Synthesis of Anatase Nanopowders by Sol-gel Method and Influence of Temperatures of Calcination to Their Photocatalitic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
The titanium dioxide (TiO2) nanopowders were produced by sol-gel technique from tetrabutyl titanate as a precursor, varying the temperature of calcination (from 500 to 550 degrees C with the step of 10 degrees C). XRPD ...