Претраживање
Приказ резултата 11-20 од 41
Electrochemical deposition and characterization of zinc-nickel alloys deposited by direct and pulse current / Elektrohemijsko taloženje i karakterizacija legura cink-nikal dobijenih konstantnom i pulsirajućom strujom
(Serbian Chemical Society, Belgrade, 2002)
Chemical composition and phase structure of Zn-Ni alloys obtained by electrochemical deposition under various conditions were investigated. The alloys were deposited on a rotating disc electrode and steel panel from chloride ...
Electrochemical deposition and characterization of Zn-Fe alloys / Elektrohemijsko taloženje i karakterizacija Zn-Fe legura
(Serbian Chemical Society, Belgrade, 2004)
Zn–Fe alloy electrochemically deposited on steel under various deposition conditions were investigated using anodic linear sweep voltammetry (ALSV) and X-ray diffraction (XRD) analysis for phase structure determination, ...
Determination of the protective properties of electrodeposited organic coatings / Određivanje zaštitnih svojstava polimernih prevlaka dobijenih postupkom elektroforetskog taloženja
(Association of Chemical Engineers of Serbia, 2001)
Using electrochemical impedance spectroscopy, thermogravimetric analysis, gravimetric liquid sorption experiments, differential scanning calorimetry and optical microscopy, the corrosion stability of organic coatings was ...
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
The study of Zn-Co alloy coatings electrochemically deposited by pulse current / Ispitivanje prevlaka Zn-Co legura dobijenih pulsirajućom strujom
(Association of Chemical Engineers of Serbia, 2012)
The electrochemical deposition by pulse current of Zn-Co alloy coatings on steel was examined, with the aim to find out whether pulse plating could produce alloys that could offer a better corrosion protection. The influence ...
Microstructure and corrosion behaviour of Zn-Co alloys deposited from three different plating baths / Mikrostruktura i koroziono ponašanje Zn-Co legura taloženih iz sulfatnog i hloridnih rastvora
(Serbian Chemical Society, Belgrade, 2011)
The effects of plating baths of different composition on the micro- structure and corrosion stability of Zn-Co alloy coatings were studied. Zn-Co alloys with the same Co content were deposited from chloride plating baths ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Engineering Society for Corrosion, Belgrade, Serbia, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
Formation of Disperse Silver Deposits by the Electrodeposition Processes at High Overpotentials
(Esg, Belgrade, 2012)
In this study, electrodeposition of silver from nitrate solution at the high overpotentials was analyzed. Morphologies of silver deposits obtained at the different overpotentials and with the different electrodeposition ...
Microindentation hardness testing of different composite systems with thin electrodeposited nickel and copper films
(Belgrade : Military Technical Institute, 2012)
Thin Ni and Cu films with fine-grained structures have been electrodeposited from self-made sulphamate-based and sulphate-based electrolytes, respectively. DC electrodeposition of Ni films was performed on single crystal ...
Manganese electrodeposition from urea-rich electrolyte
(Soc Chemists Technologists Madeconia, Skopje, 2015)
Pure manganese coatings were prepared on the steel (AISI 4340) electrode by a non-conventional electrodeposition method, in the presence of 8 mol dm(-3) of urea as a plating additive. The influence of urea on the ...