Претраживање
Приказ резултата 41-50 од 62
Hydrometallurgical recovery of tin and lead from waste printed circuit boards (wpcbs): limitations and opportunities
(Croatian Metallurgical Soc, Zagreb, 2016)
In this paper, possibility for selective Pb and Sn recovery, using three different solutions of NaOH, HCl and HNO3, from WPCBs containing low concentrations of Pb and Sn is presented. According to obtained results, over ...
Use of chènevotte, a valuable co-product of industrial hemp fiber, as adsorbent for pollutant removal. Part i: Chemical, microscopic, spectroscopic and thermogravimetric characterization of raw and modified samples
(MDPI AG, 2021)
FINEAU (2021–2024) is a trans-disciplinary research project involving French, Serbian, Italian, Portuguese and Romanian colleagues, a French agricultural cooperative and two surface-treatment industries, intending to propose ...
Novel β-galactosidase nanobiocatalyst systems for application in the synthesis of bioactive galactosides
(Royal Society of Chemistry, 2016)
In this study, unmodified, amino modified and cyanuric chloride functionalized amino modified nonporous fumed nano-silica particles (FNS, AFNS and CCAFNS, respectively) were used for the development of efficient nanobiocatalysts ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
Experimental and numerical thermo - mechanical analysis of friction stir welding of high - strength alluminium alloy
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
This paper presents experimental and numerical analysis of the change of temperature and force in the vertical direction during the friction stir welding of high-strength aluminium alloy 2024 T3. This procedure confirmed ...
The advantages of using activated flux-cored wire compared to solid wire in the mag welding process from the aspect of metallurgical characteristics
(Croatian Metallurgical Soc, Zagreb, 2014)
This paper analyzes, from the metallurgical aspect, the quality of the new flux-cored wire intended for the MAG welding process in function of changes in shielding gas composition and changes in welding parameters. The ...
Influence of friction stir welding parameters on properties of 2024 t3 aluminium alloy joints
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
The aim of this work is to analyse the process of friction stir welding (FSW) of 3 mm thick aluminium plates made of high strength aluminium alloy - 2024 T3, as well as to assess the mechanical properties of the produced ...
Amino-modified kraft lignin microspheres as a support for enzyme immobilization
(Royal Society of Chemistry, 2020)
In this research, it has been demonstrated that amino-modified microspheres (A-LMS) based on bio-waste derived material, such as kraft lignin, have good prospects in usage as a support for enzyme immobilization, since ...
Assessing the Bioactivity of Gentamicin-Preloaded Hydroxyapatite/Chitosan Composite Coating on Titanium Substrate
(Amer Chemical Soc, Washington, 2020)
The electrophoretic deposition process (EPD) was utilized to produce bioactive hydroxyapatite/chitosan (HAP/CS) and hydroxyapatite/chitosan/gentamicin (HAP/CS/Gent) coatings on titanium. The bioactivity of newly synthesized ...