Претраживање
Приказ резултата 21-30 од 35
Development of Coated Electrodes with Solid Wire and Flux-Cored Alloyed Wire for Microalloyed Steel Welding
(MDPI, Basel, 2020)
In this paper, we will present our investigation of the quality of J55 microalloyed steel welds that were formed by a basic flux-cored wire electrodes that were of appropriate quality and alloyed with Ni and Mo. Based on ...
Age hardening potential of an Al-4.6 wt.% Mg alloy with Cu addition
(Belgrade : Institute of Technical Sciences of SASA, 2010)
The ageing behavior of an Al-4.6Mg-0.54Cu (in wt.%) alloy was studied after: (i) solution
treatment for 1h at 530°C, and (ii) annealing at 280°C for 3h. Both groups of the heat treated
specimens underwent further ...
Mechanical properties of acrylate matrix composite reinforced with manganese-aluminum layered double hydroxide
(John Wiley and Sons Inc., 2023)
Acrylate polymers are used in several applications such as dentistry, medicine, and industry. The modification of their properties using the reinforcement is of key importance for the possible applications. Layered double ...
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Mechanical properties of composites based on unsaturated polyester resins obtained by chemical recycling of poly(ethylene terephthalate) / Mehanička svojstva kompozita na bazi nezasićenih poliestarskih smola dobijenih hemijskom reciklažom poli(etilen-tereftalata)
(Association of Chemical Engineers of Serbia, 2013)
Composites based on unsaturated polyester (UPe) resins and fumed silica AEROSIL® RY 50, NY 50, RX 50 and NAX 50, as well as graphite, TiO2 or organically modified clay CLOISITE 30B were prepared in order to investigate the ...
Design of halloysite modification for improvement of mechanical properties of the epoxy based nanocomposites
(Polymer Composites, 2021)
In this study, halloysite nanotubes (HNT) were modified by: 3-glycidyloxypropyltrimethoxysilane (GLYMO), 3-aminopropyltrimethoxysilane (APTES), and 2,2-Bis[4-(glycidyloxy) phenyl] propane (DGEBA), and incorporated in the ...
Synthesis of α-Al2O3 based foams with improved properties as catalyst carriers
(Institute of Metals and Technology, 2014)
This paper explores the possibility of synthesising catalyst supports with improved properties. Alumina foams were produced with the polymer replication technique. Representative high- and low-temperature sintering ceramics ...
Mechanical properties of two Al-Mg alloys manufactured by accumulative roll bonding (ARB) process
(Belgrade : Association of Metallurgical Engineers of Serbia (AMES), 2017)
The influence of alloying on the mechanical properties of AA5083 type Al-Mg
alloy sheets produced by accumulative roll bonding (ARB) process was studied.
Two investigated Al-Mg alloys: commercial AA5083 alloy with 4.2% ...
Studying the influence of common wet processes on the quality of 1 × 1 rib cotton/elastane knitted fabrics
(SAGE Publications Ltd, 2022)
This research studied the influence of common wet processes (i.e. bleaching, dyeing, or softening) on the quality of 1 × 1 rib cotton/elastane knitted fabrics. The changes in their structural (thickness, weight, and stitch ...
The effect of natural modifiers for starch hydrophobization on performance of composite based on ethylene acrylic acid copolymer
(Wiley, Hoboken, 2021)
As a renewable resource, starch is considered to be fully biodegradable and nonpolluting to the environment but the hygroscopicity of starch is the main disadvantage for wider applicability in the production of a polymer-based ...