Претраживање
Приказ резултата 1-10 од 40
Synthesis and sintering of Cu-Al2O3 nanocomposite powders produced by a thermochemical route
(Savez inženjera metalurgije Srbije, Beograd, 2007)
By hydrometallurgy and powder metallurgy along with prognosis of physical-chemical properties, a synthesis of new improved materials can be successfully performed with in advance pre-set properties which is conditioned by ...
Analysis of the properties of a Cu-Al2-O3 sintered system based on ultra fine and nanocomposite powders
(International Institute for the Science of Sintering, Beograd, 2007)
In this paper synthesis of a composite based on Cu-Al2O3 by a thermo-chemical method is shown along with a comparative analysis of the properties of the obtained nanocomposite sintered samples, which are characterized by ...
Influence of milling parameters on the preparation of fine tungsten and copper powders by mechanically induced self-propagating reaction / Uticaj parametara mlevenja na dobijanje finih prahova volframa i bakra mehanički iniciranom samorasprostirućom reakcijom
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Mechanically induced self-propagating reaction in planetary ball mill was realized in three different systems, CaWO4 (scheelite) + Mg, CuO + Ti and CuO + Zr. An influence of a ball diameter (from 5 to 41.2 mm) at three ...
Hydrometallurgical Process for Selective Metals Recovery from Waste-Printed Circuit Boards
(MDPI, Basel, 2018)
This paper presents an experimentally-proved hydrometallurgical process for selective metals recovery from the waste-printed circuit boards (WPCBs) using a combination of conventional and time-saving methods: leaching, ...
Metal-loaded zeolite remediation of soils contaminated with pandrug-resistant Acinetobacter baumannii
(Inst Medical Research & Occupational Health, Zagreb, 2020)
Due to the development of resistance to antimicrobial agents, bacterium Acinetobacter baumannii is nowadays a leading cause of nosocomial outbreaks. Clinically relevant A. baumannii outside hospital settings including ...
Determination of AL2O3particle size in Cu-AL2O3 nanocomposite materials using UV spectrophotometry / Određivanje veličine čestica AL2O3 u nanokompozitnim materijalima iz sistema Cu-AL2O3 primenom UV spektrofotometrije
(Savez inženjera metalurgije Srbije, Beograd, 2008)
In order to achieve improved mechanical properties of dispersion strengthened nanocomposite, without influencing electrical and thermal conductivity it is necessary for dispersoide to be nano sized and uniformly distributed ...
Easy, Flexible and Standardizable Anti-Nascent Biofilm Activity Assay to Assess Implant Materials
(MDPI, 2023)
Medical implants have improved the quality of life of many patients. However, surgical intervention may eventually lead to implant microbial contamination. The aims of this research were to develop an easy, robust, ...
Copper Separation from Aqueous Effluents by Liquid Membrane Pertraction
(International Ecological Congress, Voronezh, Russia, September 22-28, 1996)
In this paper the feasibility of applying liquid membrane pertraction to the copper
recovery from aqueous effluents has been examined. A continuos laboratory-scale
hollow fiber-in-fiber type membrane pertractor was ...
Electrochemical synthesis and corrosion behavior of thin polyaniline film on mild steel, copper and aluminum
(Belgrade : Association of the Chemical Engineers of Serbia, 2011)
The electrochemical synthesis of polyaniline (PANI) on mild steel, aluminum and copper from the sodium benzoate solutions has been investigated. It has been shown that thin, highly adherent, polyaniline films on the ...
Mechanical Properties of Electrolytically Produced Copper Coatings Reinforced with Pigment Particles
(MDPI, 2023)
Copper from sulfate baths without and with added inorganic pigment particles based on strontium aluminate doped with europium and dysprosium (SrAl2O4: Eu2+, Dy3+) was electrodeposited on a brass cathode by a galvanostatic ...