Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes
Konferencijski prilog (Objavljena verzija)
Metapodaci
Prikaz svih podataka o dokumentuApstrakt
Supercritical carbon dioxide (sCO2) is an ideal low-temperature cosolvent for perovskite
deposition due to its relatively low critical point (31.2 °C, 73.8 bar), no surface tension, liquidlike density, gas-like viscosity, and diffusivity. It enables faster mass transfer which allows
penetration of crystals in nanoporous structure. The study investigates the influence of time of
deposition of perovskite assisted with supercritical carbon dioxide on the filling of nanotubes.
Perovskite solar cell technology has been developed so fast due to several factors including a
tunable band gap, high absorption coefficient, and low-cost fabrication. The quality of the
perovskite film is important for the high efficiency of perovskite solar cells. Perovskite precursors
are usually deposited from the solution onto a substrate using spin-coating followed by postdeposition treatments, but often it results in low-quality films that cannot provide good
photovoltaic performances. Deposition of pe...rovskite in the presence of sCO2 is a promising
method for the formation of high-quality perovskite layers. In this work, methylammonium lead
bromide perovskite (MAPbBr3) was deposited on TiO2 nanotubes from the solution in
dimethylformamide (DMF) by application of sCO2 at 35 °C and 200 bar for 1 h, and 3 h. FESEM
results show that TiO2 nanotubes were filled with perovskite material in both cases. The diffuse
reflectance spectroscopy measurement of samples proved that the absorption edge of prepared
TiO2 nanotubes/MAPbBr3 was extended to the visible range. Measurement of I-V characteristics
showed that the sample made for 3 h had a higher value of current than the sample prepared for 1
h. The application of sCO2 during the deposition of perovskite has enabled the preparation of a
photodiode with a better contact between TiO2 nanotubes and perovskite which is important for
the future development of solar cells.
Izvor:
23th Annual Conference YUCOMAT 2022 and 12th WRTCS, 2022, 73-Izdavač:
- Materials Research Society of Serbia
Institucija/grupa
Inovacioni centarTY - CONF AU - Stefanović, Milica AU - Lukić, Ivana AU - Vujančević, Jelena AU - Petrović, Rada AU - Janaćković, Đorđe PY - 2022 UR - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6170 AB - Supercritical carbon dioxide (sCO2) is an ideal low-temperature cosolvent for perovskite deposition due to its relatively low critical point (31.2 °C, 73.8 bar), no surface tension, liquidlike density, gas-like viscosity, and diffusivity. It enables faster mass transfer which allows penetration of crystals in nanoporous structure. The study investigates the influence of time of deposition of perovskite assisted with supercritical carbon dioxide on the filling of nanotubes. Perovskite solar cell technology has been developed so fast due to several factors including a tunable band gap, high absorption coefficient, and low-cost fabrication. The quality of the perovskite film is important for the high efficiency of perovskite solar cells. Perovskite precursors are usually deposited from the solution onto a substrate using spin-coating followed by postdeposition treatments, but often it results in low-quality films that cannot provide good photovoltaic performances. Deposition of perovskite in the presence of sCO2 is a promising method for the formation of high-quality perovskite layers. In this work, methylammonium lead bromide perovskite (MAPbBr3) was deposited on TiO2 nanotubes from the solution in dimethylformamide (DMF) by application of sCO2 at 35 °C and 200 bar for 1 h, and 3 h. FESEM results show that TiO2 nanotubes were filled with perovskite material in both cases. The diffuse reflectance spectroscopy measurement of samples proved that the absorption edge of prepared TiO2 nanotubes/MAPbBr3 was extended to the visible range. Measurement of I-V characteristics showed that the sample made for 3 h had a higher value of current than the sample prepared for 1 h. The application of sCO2 during the deposition of perovskite has enabled the preparation of a photodiode with a better contact between TiO2 nanotubes and perovskite which is important for the future development of solar cells. PB - Materials Research Society of Serbia C3 - 23th Annual Conference YUCOMAT 2022 and 12th WRTCS T1 - Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes SP - 73 UR - https://hdl.handle.net/21.15107/rcub_technorep_6170 ER -
@conference{ author = "Stefanović, Milica and Lukić, Ivana and Vujančević, Jelena and Petrović, Rada and Janaćković, Đorđe", year = "2022", abstract = "Supercritical carbon dioxide (sCO2) is an ideal low-temperature cosolvent for perovskite deposition due to its relatively low critical point (31.2 °C, 73.8 bar), no surface tension, liquidlike density, gas-like viscosity, and diffusivity. It enables faster mass transfer which allows penetration of crystals in nanoporous structure. The study investigates the influence of time of deposition of perovskite assisted with supercritical carbon dioxide on the filling of nanotubes. Perovskite solar cell technology has been developed so fast due to several factors including a tunable band gap, high absorption coefficient, and low-cost fabrication. The quality of the perovskite film is important for the high efficiency of perovskite solar cells. Perovskite precursors are usually deposited from the solution onto a substrate using spin-coating followed by postdeposition treatments, but often it results in low-quality films that cannot provide good photovoltaic performances. Deposition of perovskite in the presence of sCO2 is a promising method for the formation of high-quality perovskite layers. In this work, methylammonium lead bromide perovskite (MAPbBr3) was deposited on TiO2 nanotubes from the solution in dimethylformamide (DMF) by application of sCO2 at 35 °C and 200 bar for 1 h, and 3 h. FESEM results show that TiO2 nanotubes were filled with perovskite material in both cases. The diffuse reflectance spectroscopy measurement of samples proved that the absorption edge of prepared TiO2 nanotubes/MAPbBr3 was extended to the visible range. Measurement of I-V characteristics showed that the sample made for 3 h had a higher value of current than the sample prepared for 1 h. The application of sCO2 during the deposition of perovskite has enabled the preparation of a photodiode with a better contact between TiO2 nanotubes and perovskite which is important for the future development of solar cells.", publisher = "Materials Research Society of Serbia", journal = "23th Annual Conference YUCOMAT 2022 and 12th WRTCS", title = "Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes", pages = "73", url = "https://hdl.handle.net/21.15107/rcub_technorep_6170" }
Stefanović, M., Lukić, I., Vujančević, J., Petrović, R.,& Janaćković, Đ.. (2022). Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes. in 23th Annual Conference YUCOMAT 2022 and 12th WRTCS Materials Research Society of Serbia., 73. https://hdl.handle.net/21.15107/rcub_technorep_6170
Stefanović M, Lukić I, Vujančević J, Petrović R, Janaćković Đ. Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes. in 23th Annual Conference YUCOMAT 2022 and 12th WRTCS. 2022;:73. https://hdl.handle.net/21.15107/rcub_technorep_6170 .
Stefanović, Milica, Lukić, Ivana, Vujančević, Jelena, Petrović, Rada, Janaćković, Đorđe, "Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes" in 23th Annual Conference YUCOMAT 2022 and 12th WRTCS (2022):73, https://hdl.handle.net/21.15107/rcub_technorep_6170 .