Pretraživanje
Prikaz rezultata 11-20 od 39
Improvement of mechanical properties and antibacterial activity of crosslinked electrospun chitosan/poly (ethylene oxide) nanofibers
(Elsevier Sci Ltd, Oxford, 2017)
In this study conditions for green crosslinking with citric acid of chitosan/PEO (polyethylene oxide) nanofibers were evaluated. The thermal in situ crosslinking enabled penetration of crosslinking agent into the matrix ...
Microstructure and mechanical properties of Al-4·4 wt-%Mg alloy (AA5182) after equal channel angular pressing
(Maney Publishing, 2005)
Equal channel angular pressing (ECAP) has been used to process an Al-4-4 wt-%Mg alloy (AA5182) at room temperature (RT), 200°C and 400°C. The evolution of microstructure and mechanical properties after ECAP has been studied ...
Processing of dense nanostructured HAP ceramics by sintering and hot pressing
(Elsevier Sci Ltd, Oxford, 2009)
A nanosized HAP powder was sintered and hot pressed, in order to obtain dense HAP ceramics. In a first series of experiments, the powder was isostatically pressed into uniform green compacts and sintered at temperatures ...
Influence of microstructure and phase composition on the nanoindentation characterization of bioceramic materials based on hydroxyapatite
(Elsevier Sci Ltd, Oxford, 2009)
The aim of the study was to investigate the influence of microstructure and phase composition on the mechanical behaviour of hydroxyapatite (HAp) and biphasic HAp/beta-tricalcium phosphate (beta-TCP) bioceramic materials ...
Synthesis and characterization of silver/poly(N-vinyl-2-pyrrolidone) hydrogel nanocomposite obtained by in situ radiolytic method
(Pergamon-Elsevier Science Ltd, Oxford, 2011)
This work describes radiolytic synthesis of silver nanoparticles (Ag NPs) within the poly(N-vinyl-2-pyrrolidone) (PVP) hydrogel. The hydrogel matrix was obtained by gamma irradiation-induced cross-linking, while the in ...
Thermoplastic Copolyester Elastomers
(Handbook of Engineering and Speciality Thermoplastics: Polyethers and Polyesters, 2011)
In this chapter the preparation, structure and properties of thermoplastic copolyester elastomers, TPEE, are presented. TPEEs are multiblock copolymers built up from so-called short crystallizable hard segments and long ...
Optimization of modifier deposition on the alumina surface to enhance mechanical properties and cavitation resistance
(Springer, New York, 2020)
Composites based on poly(methyl methacrylate), dimethyl itaconate matrix and alumina particles were prepared. Ferrous oxide-doped alumina particles (Al2O3Fe) and commercial alumina nanoparticles (Al(2)O(3)n) modified with ...
Composite materials from fully bio-based thermosetting resins and recycled waste poly(ethylene terephthalate)
(Elsevier Sci Ltd, Oxford, 2018)
During the last two decades, interest in bio-based polymers, especially in bio-based composite materials, has grown as a result of environmental concerns. In this paper new composites obtained from fully bio-based unsaturated ...
Mg/Cu co-substituted hydroxyapatite - Biocompatibility, mechanical properties and antimicrobial activity
(Elsevier Sci Ltd, Oxford, 2019)
The aim of this study was to improve the mechanical properties and to optimize antimicrobial activity of hydroxyapatite (HAP) by simultaneous doping with Mg and Cu ions in order to obtain material that would be able to ...
The effect of graphene loading on mechanical, thermal and biological properties of poly(vinyl alcohol)/graphene nanocomposites
(Elsevier Science Inc, New York, 2016)
Poly(vinyl alcohol)/graphene (PVA/Gr) nanocomposite was synthesized with the aim of developing a novel improved material. The PVA/Gr nanocomposite was characterized by UV-visible spectroscopy, cyclic voltammetry, Raman ...