Претраживање
Приказ резултата 1-10 од 57
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheet
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheets was examined after cold rolling and annealing in the range of temperature from 220°C to 520°C, water quenching and natural aging. The low temperature annealed ...
Structural characteristics of some ternary Ag-In-Sn alloys
(Savez inženjera metalurgije Srbije, Beograd, 2008)
The Ag-In-Sn system, as one of potential lead-free solder materials, was studied in this paper. The investigated alloys were chosen from two sections, with molar ratio of In:Sn equal to 1:4; 1:2. DTA, XRD, SEM and micro ...
The effect of heat treatment on toughness and wear resistance of Fe-Cr-C-Nb alloys / Uticaj termičke obrade na žilavost i otpornost na habanje Fe-Cr-C-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Alloying with niobium improves the mechanical properties of the high chromium irons. The alloy containing appriximately 3 %Nb gives the best compromise between wear resistance and toughness. These properties were improved ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Problems and prospect of Al-Mg alloys application in marine constructions
(Savez inženjera metalurgije Srbije, Beograd, 2006)
The position of steel as the most widely used material in the shipbuilding industry originates from the superior mechanical properties and low manufacturing costs The increasing demands for lowering the weight of different ...
Application of instrumental methods in the investigation of properties and microstructure of construction concretes / Primena instrumentalnih metoda za ispitivanje svojstava i mikrostrukture konstukcionih betona
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Methods for the investigation of microstructure of construction concretes are presented in this paper. Concrete is a composite material, thus its microstructure consists of bonding agent (cement) and aggregate with predefined ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1 Investigations were performed on superalloy single crystals based Ni which were ...
Influence of Cu and Mn content on the properties of Al-Mg4.5-(Mn,Cu) type alloy sheets
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Influence of Cu and Mn content on the grain structure, precipitation effects and mechanical properties of two Al-Mg4.5-(Mn,Cu) type sheets was considered. It was found that a variety of grain size can be obtained in alloy ...
Characterization of thermal shock damage in cordierite-mullite refractory materials by non-destructive methods
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Ultrasonic pulse velocity testing and image analysis were used to predict thermal stability of refractories. Two cordierite-mullite compositions used as substrates in fast firing of porcelain white ware characterized by ...