Pretraživanje
Prikaz rezultata 1-10 od 168
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
Effect of process parameters on the phase transformation kinetics in copper-based alloys and composites
(Metallurgical & Materials Engineering, 2020)
Copper-based alloys and composites, owing to their convenient properties, are being considered essential materials in various industries. Since copper possesses an ability to develop high corrosion resistance, putting it ...
Treatment of waste sulfuric acid copper electrolyte / Tretman otpadnog sumporno-kiselog elektrolita bakra
(Institut za rudarstvo i metalurgiju, Bor, 2014)
The aim of this paper was to investigate the possibility of using the copper anodes with high nickel content for electrolytic treatment of waste sulfuric acid copper electrolyte. Nickel content in each anode was about 10 ...
Polymer bonded magnetic composites based on Nd-Fe-B / Polimerni magnetni kompoziti na bazi Nd-Fe-B
(Inženjersko društvo za koroziju, Beograd, 2013)
Various types and contents of magnetic powder and polymer matrix induce different mechanical, magnetic, electrical and optical properties of final composite material. The strong influence of relatively small amounts of ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
PtAu catalyst with enhanced activity for formic acid oxidation / PtAu katalizator sa poboljšanom aktivnošću za reakciju oksidacije mravlje kiseline
(Engineering Society for Corrosion, Belgrade, Serbia, 2018)
PtAu systems are recognized as good catalysts for the oxidation of formic acid electrooxidation, which is investigated as a possible anodic reaction in low-temperature fuel cells. In this research, bimetallic PtAu ...
Influence of the fabrication process of copper matrix composites on cavitation erosion resistance
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations ...
Treatment of dispersed iron-bearing raw materials and modeling of the protection systems against air-pollution
(Association of Metallurgical Engineers of Serbia, 2016)
Based on the analysis of the non-standard iron-bearing raw materials treatment process and the results of real composition measurements of the flue gas, the study of hazards by identification of harmful substances that ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
Effect of vibration on the variation of residual stresses and impact energy in butt-welded joints / Uticaj vibracija na promenu zaostalih napona i energije udara kod sučeono zavarenih spojeva
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
The effect of vibration on the variation of residual stresses in butt-welded steel plates and on the impact energy in characteristic zones of a welded joint is analysed in this paper. An important segment occurring as a ...