Претраживање
Приказ резултата 31-40 од 2709
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Inženjersko društvo za koroziju, Beograd, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
Innovative and generic pharmaceuticals industry and drugs market / Inovativna i generička farmaceutska industrija i tržište lekova
(Economics institute, Belgrade, 2010)
The pharmaceutical industry consists of two sectors: the innovative sector and generic sector. The innovative pharmaceutical industry is totally dependent on patents and these companies are focused on protecting against ...
Possibility of secondary lead slag stabilization in concrete with presence of selected additives
(Savez inženjera metalurgije Srbije, Beograd, 2010)
A comparative technical and environmental evaluation of products arising from the stabilization/solidification of secondary lead metallurgical slag into a cement matrix was performed. Provided samples of an industrial slag ...
Differences in the electrochemical behavior of ruthenium and iridium oxide in electrocatalytic coatings of activated titanium anodes prepared by the sol-gel procedure / Razlike u elektrohemijskom ponašanju oksida rutenijuma i iridijuma u elektrokatalitičkim prevlakama aktiviranih titanskih anoda dobijenih sol-gel postupkom
(Serbian Chemical Society, Belgrade, 2010)
The electrochemical characteristics of Ti0.6Ir0.4O2/Ti and Ti0.6Ru0.4O2/Ti anodes prepared by the sol-gel procedure from the corresponding oxide sols, obtained by force hydrolysis of the corresponding metal chlorides, were ...
Hydroxyapatite coatings on TiO2 nanotubes / Prevlake hidroksiapatita na nanotubama oksida titana
(Engineering Society for Corrosion, Belgrade, Serbia, 2010)
The aim of this work was to obtain nanotubular TiO2 layer by anodization of titanium substrate, and to prepare hydroxyapatite (HAP) coatings by electrophoretic deposition over nanotubular TiO2 layer. The presence of fluoride ...
Solubility in K+-Na+-Mg (4) (2-) aqueous solution at T=298.15 K
(Maik Nauka/Interperiodica/Springer, New York, 2013)
In the salt solubility predictions for K+-Na+-Mg (4) (2-) aqueous solution the treatment of thermodynamic data of three-component systems at T = 298.15 K involved the application of the Extended Pitzer's ion-interaction ...
N-H···O hydrogen bonding: An FT-IR, NIR study of N-methylformamide-ether systems / N-H···O vodonična veza - FT-IR i NIR spektroskopsko ispitivanje sistema N-metilformamid-etri
(Serbian Chemical Society, Belgrade, 2010)
This paper reports the results of an FT-IR and NIR study of N-methylformamide in carbon tetrachloride solution in presence of ethers as the O-electron donors, i.e., diethyl ether (DEE), diisopropyl ether (DiPE), methyl t- ...
Initial corrosion protection of Zn-Mn alloys electrodeposited from alkaline solution
(Pergamon-Elsevier Science Ltd, Oxford, 2011)
The effects of a deposition current density (c.d.) on the corrosion behaviour of Zn-Mn alloy coatings, deposited from alkaline pyrophosphate solution, were investigated by atomic absorption spectrophotometry (AAS), X-ray ...
Phase transition at subcritical and supercritical conditions of triglycerides methanolysis
(Elsevier, Amsterdam, 2010)
The analysis of phase equilibrium between methanol and glycerides during methyl esters of fatty acids (FAME or biodiesel) synthesis at high pressure and temperature is very important for describing the kinetic and process ...
The influence of the parameters of lost foam process on the quality of aluminum alloys castings / Uticaj parametara lost foam procesa na kvalitet odlivaka legura aluminijuma
(Association of Chemical Engineers of Serbia, 2010)
This paper presents the research results of application of Lost foam process for aluminum alloys castings of a simple geometry. The process characteristic is that patterns and gating of moulds, made of polymers, stay in ...