Pretraživanje
Prikaz rezultata 1-10 od 75
TiO2 nanotubes film/FTO glass interface: Thermal treatment effects
(ETRAN, 2022)
Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal ...
Preparation and Characterization of Novel Glycidyl Methacrylate/Clay Nanocomposites
(Science of SinteringScience of Sintering, 2022)
The impact of the type and amounts of nanofiller on the features of the glycidyl methacrylate-co-ethylene glycol dimethacrylate (GMA-co-EGDMA)/organomodified montmorillonite (OMt) nanocomposites that were prepared by in ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
Analysis of the properties of a Cu-Al2-O3 sintered system based on ultra fine and nanocomposite powders
(International Institute for the Science of Sintering, Beograd, 2007)
In this paper synthesis of a composite based on Cu-Al2O3 by a thermo-chemical method is shown along with a comparative analysis of the properties of the obtained nanocomposite sintered samples, which are characterized by ...
Modeling of coating optical fibers with polymer-magnetic powder composite coating
(International Institute for the Science of Sintering, Beograd, 2002)
A mathematical model of forming a composite coating on optical fiber was established. The model is based on existing mathematical models for coating optical fibers with polymer coating and experimentally defined rheological ...
The Influence of Powder Particle Size on Properties of Cu-Al2O3 Composites
(International Institute for the Science of Sintering (IISS), 2009)
Inert gas atomized prealloyed copper powder containing 2 wt.% Al (average particle size approximate to 30 mu m) and a mixture consisting of copper (average particle sizes approximate to 15 mu m and 30 mu m) and 4 wt.% of ...
Morphological and Structural Characterization of MgAl2O4 Spinel
(International Institute for the Science of Sintering (IISS), 2023)
Magnesium aluminate has the spinel structure along with good mechanical, chemical, and thermal properties. Magnesium aluminate has a wide range of applications including refractory ceramics, optically transparent ceramic ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
The Mechanisms of Cavitation Erosion of Raw and Sintered Basalt
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
The paper analyzes the morphology of cavitation damage of raw and sintered basalt samples. The experiment was conducted using the ultrasonic vibratory cavitation test method according to the ASTM G-32 standard. During the ...
The crystal growth of NASICON phase from the lithium germanium phosphate glass
(International Institute for the Science of Sintering, 2023)
The crystal growth rate of LiGe2(PO4)3 phase from lithium germanium-phosphate glass was studied. The glass have been homogenized using the previously established temperature-time conditions, which make it possible to remove ...