Претраживање
Приказ резултата 21-30 од 146
Oxidation and erosion behaviour of SiC-HfC multilayered composite
(Univerzitet u Novom Sadu - Tehnološki fakultet, Novi Sad, 2014)
The fabrication of SiC-HfC ceramic composite via self-propagating high-temperature synthesis and simultaneous consolidation was investigated. Dense composite consisting of alternating layers of SiC and HfC was obtained by ...
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
Nanostructured intrinsically conducting polymers formed by electrochemical synthesis / Nanostruktuirani elektroprovodni polimeri dobijeni elektrohemijskom sintezom
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Due to unique properties of intrinsically conducting polymers (ICP) such as: electrical conductivity, reversible electrochemistry, optical activity, biocompatibility, environmental and corrosion stability, they still ...
Polymer bonded magnetic composites based on Nd-Fe-B / Polimerni magnetni kompoziti na bazi Nd-Fe-B
(Inženjersko društvo za koroziju, Beograd, 2013)
Various types and contents of magnetic powder and polymer matrix induce different mechanical, magnetic, electrical and optical properties of final composite material. The strong influence of relatively small amounts of ...
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
Time: Temperature superposition principle: Application of WLF equation in polymer analysis and composites / Princip superponiranja vremena i temperature - primena WLF jednačine za ispitivanje polimera i kompozita
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Polymers are the most studied viscoelastic material. The shorter times (high frequencies) corresponding to lower temperatures and long times (low frequencies) to high temperatures. This represents the quantitatively applied ...
Treatment of waste sulfuric acid copper electrolyte / Tretman otpadnog sumporno-kiselog elektrolita bakra
(Institut za rudarstvo i metalurgiju, Bor, 2014)
The aim of this paper was to investigate the possibility of using the copper anodes with high nickel content for electrolytic treatment of waste sulfuric acid copper electrolyte. Nickel content in each anode was about 10 ...
Microstructural characterization of glass-epoxy composites subjected to tensile testing / Mikromehanička karakterizacija staklo-epoksi kompozita izloženog zateznom opterećenju
(Faculty of Technology, Novi Sad, 2013)
The main objective of the research presented in this paper was to carry out a statistical-mechanical analysis concerning the tensile test of glass-epoxy composite materials in order to calculate their relevant tension ...
The effect of cooling rate of slag from primary copper production in the valorization of copper in the flotation process
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Technological procedure of slow cooling slag from primary copper production is applied in the purpose of copper recovery in the level of 98.5% to blister. This technological procedure is divided into two phases, first slow ...