Претраживање
Приказ резултата 21-30 од 40
Comparison of Morphological Parameters of Ceramic Materials Surface Damage Exposed to Thermal Shock and Cavitation Erosion
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
The surface defects on the samples, which are based on alumina, exposed to thermal shocks and cavitations erosion were analyzed using image analysis. For both types of experimental testing, the samples are made of the same ...
The Influence of Barium Ferrite Nanoparticles on Morphological and Mechanical Properties of Ethyl Cellulose Based Nanocomposites
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
This study presents preparation and characterization of ethyl cellulose based nanocomposites. Successful use of simple solvent casting technique provided nanocomposites with high loads of barium ferrite magnetic nanopowder ...
Characterization of MgAl2O4 Sintered Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Single phase MgAl2O4 was made from a one-to-one molar ratio of MgO and Al2O3 powders mixed using ball-milling. Mixtures of MgO and Al2O3 were subsequently treated in planetary ball mill for 30, 60, 90 and 120 minutes in ...
The Thermophysical Properties of Primary Phase in Lithium Germanium Phosphate Glass
(Science of Sintering, 2021)
The selected lithium germanium-phosphate glass was prepared by a conventional melt-quenching technique. The XRD method was employed to confirm the glass was obtained and to reveal crystalline phases during heat treatment. ...
Novel Method for Measurement of Pipeline Materials Fracture Resistance-Examination on Selective Laser Sintered Cylindrical Specimens
(International Institute for the Science of Sintering (IISS), 2022)
This paper presents a part of development of a non-standard method for testing of cylindrical test specimens for measurement of fracture properties of pipeline materials. This method for testing of cylindrical structures ...
An Experimental Study of Mechanical Properties and Heat Transfer of Acrylic Composites with Structural and Surface Modified Al2O3 Particles
(International Institute for the Science of Sintering (IISS), 2020)
Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat ...
Evaluation of Adsorption Performance and Quantum Chemical Modeling of Pesticides Removal using Cell-MG Hybrid Adsorbent
(Science of Sintering, 2021)
Magnetite (MG) modified cellulose membrane (Cell-MG), obtained by reaction of 3-aminosilane and subsequently with diethylenetriaminepentaacetic acid dianhydride functionalized waste Cell fibers (Cell-NH2 and Cell-DTPA, ...
Cavitation Properties of Rendering Mortars with Micro Silica Addition
(Science of Sintering, 2021)
Micro-silica is a highly efficient mineral additive whose role is reflected in improvements of microstructure packing, strength and durability of non-shaped composite building materials such as concrete and mortar. A ...
Sintered materials based on copper and alumina powders synthesized by a novel method
(International Institute for the Science of Sintering, Beograd, 2010)
This paper presents the production of sintered materials from nano-composite powders obtained by a novel synthesis method, which represents a combination of thermochemical synthesis and mechanical alloying. Produced powders ...
Anisotropy Analysis of Low Cement Concrete by Ultrasonic Measurements and Image Analysis
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
The analized material was high alumina low cement castable sintered at three different temperatures. Influence of initial material anisotropy on the thermal shock resistance as well as changes of anisotropy level during ...