Претраживање
Приказ резултата 1-10 од 579
Use of chènevotte, a valuable co-product of industrial hemp fiber, as adsorbent for pollutant removal. Part i: Chemical, microscopic, spectroscopic and thermogravimetric characterization of raw and modified samples
(MDPI AG, 2021)
FINEAU (2021–2024) is a trans-disciplinary research project involving French, Serbian, Italian, Portuguese and Romanian colleagues, a French agricultural cooperative and two surface-treatment industries, intending to propose ...
Immobilization of Aspergillus Niger cellulase onto Lifetech TM carriers and its application in the hydrolysis of sunflower seed meal lignocellulosic fraction / Imobilizacija Aspergillus Niger celulaze na Lifetech TM nosače i primena u reakciji hidrolize lignocelulozne frakcije suncokretove sačme
(Institute for Food Technology, Novi Sad, 2019)
Cellulases are enzymes which catalyse cellulose hydrolysis and are widely used in various industry branches. Lately, their application in treatment of different agroindustrial waste materials which could serve for fuel ...
Enzymatic synthesis of fructo-oligosaccharides using Pectinex® Ultra SP-L: a study of experimental conditions / Enzimska sinteza frukto-oligosaharida upotrebom Pectinex® Ultra SP-L: ispitivanje uticaja eksperimentalnih uslova
(Institute for Food Technology, 2021)
The obvious benefits of employing prebiotics as functional components in many foods
and feed products have resulted in higher demand for their industrial production, necessitating the
development of more efficient and ...
The Design of a System for the Induction Hardening of Steels Using Simulation Parameters
(MDPI, 2023)
This paper presents the development of a piece of induction hardening equipment based on the foundations of the design, starting from zero. It was intended for steels in general, and was tested on unalloyed low- and ...
CELLULOSE-BASED WASTE STRUCTURE AND CHEMICAL COMPOSITION IMPACT ON THE ADSORPTION OF PHARMACEUTICALS / UTICAJ STRUKTURE I HEMIJSKOG SASTAVA CELULOZNOG OTPADA NA ADSORPCIJU FARMACEUTIKA
(Savez inženjera i tehničara tekstilaca Srbije, 2023)
In an attempt to reuse fibrous textile waste, and at the same time to reduce its quantity, waste hemp and
flax fibers, and cotton yarn were used as cheap and sustainable adsorbents for the removal of pharmaceuticals
from ...
INTERGRANULAR CORROSION OF WELDED JOINTS. FORMING CONDITIONS AND PROCEDURES FOR PREVENTION
(INTEGRITET I VEK KONSTRUKCIJA, 2013)
The paper describes structural changes in the welded joints, leading to the emergence of intergranular corrosion (IGC) during exploitation. The occurrence of intergranular corrosion in welded joints of austenitic, ferritic ...
Thermo-mechanical analysis of linear welding stage in friction stir welding Influence of Welding Parameters
(VINČA Institute of Nuclear Sciences, 2022)
The influence of friction stir welding parameters on thermo-mechanical behavior of the material during welding is analyzed. An aluminum alloy is considered (Al 2024 T351), and different rotating and welding speeds are ...
Implementation of the electrohydrodynamics' perfect dielectric model in OpenFOAM®
(University of East Sarajevo, Faculty of Technology Zvornik, 2022)
The electrohydrodynamics' (EHD) perfect dielectric model was added into computational fluid dynamics (CFD) software OpenFOAM® in order to improve its usability for the EHD field and specifically for the mentioned model. ...
Heat generation during plunge stage in friction stir welding
(Vinca Institute of Nuclear Sciences, 2013)
This paper deals with the heat generation in the Al alloy Al2024-T3 plate under different rotating speeds and plunge speeds during the plunge stage of friction stir welding. A 3-D finite element model is developed in the ...
Analysis of the tool plunge in friction stir welding comparison of aluminum alloys 2024 t3 and 2024 t351
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2016)
Temperature, plastic strain and heat generation during the plunge stage of the friction stir welding of high-strength aluminum alloys 2024 T3 and 2024 T351 are considered in this work. The plunging of the tool into the ...