Претраживање
Приказ резултата 1-10 од 19
Structural, Morphological and Electrical Properties of Alumina/YAG Composites as Solid Electrolyte for IT - SOFC
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
Alumina/YAG composites (AYX_t) with high relative density (99.2 %TD) were successfully obtained by mixing commercial alumina powder with different volume fractions of yttrium aluminium garnet (Y3Al5O12-YAG; 7, 14, 21 and ...
Effect of milling and annealing on microstructural, electrical and magnetic properties of electrodeposited Ni-11.3 Fe-1.4w alloy
(International Institute for the Science of Sintering, Beograd, 2012)
A nanostructured Ni-11.3Fe-1.4W alloy deposit was obtained from an ammonium citrate bath at a current density of 600 mAcm-2. XRD analysis shows that the deposit contains an amorphous matrix having embedded nanocrystals of ...
Effect of Electrodeposition Current Density on the Microstructure and Magnetic Properties of Nickel-cobalt-molybdenum Alloy Powders
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Nanostructured nickel-cobalt-molybdenum alloy powders were electrodeposited from an ammonium sulfate bath. The powders mostly consist of an amorphous phase and a very small amount of nanocrystals with an mean size of less ...
Photocatalytic Degradation of Bisphenol A with alpha-Fe2O3 Fibers and Particles
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Two-step synthesis of Fe2O3 particles, performed by precipitation from iron(III) chloride (FeCl3 center dot 6H(2)O) using ammonium hydroxide in first step and calcination at 400 and 700 degrees C during 4 h, provided Fe2O3 ...
Structure and photocatalytic properties of sintered TiO2 nanotube arrays
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
One-dimensional (1D) TiO2 nanotubes perpendicular to the substrate were obtained by electrochemical oxidation of titanium foil in an acid electrolyte. In order to alter the crystallinity and the morphology of films the ...
Basalt-Polyester Hybrid Composite Materials for Demanding Wear Applications
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2020)
Basalt as a filler in a polymer-based composite material fulfils the demand of being natural, environment-friendly material for the production of various composite materials. The material could be used as protective layer ...
Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles – Principal Component Analysis
(International Institute for the Science of Sintering, 2018)
This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 ...
Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent
(International Institute for the Science of Sintering (IISS), 2022)
In this study, the structure, morphology and composition of the synthesized magnetite/3D-printed wollastonite (3D_W/M) composite were characterized, and its adsorption performance with respect to As(V) and Cr(VI) were ...
Solid state synthesis of extra phase-pure Li4Ti5O12 spinel
(Belgrade : International Institute for the Science of Sintering, 2011)
Extra phase-pure Li4Ti5O12 spinel with particle sizes less than 500 nm was synthesized by solid state reaction of mechanochemicaly activated mixture of nano anatase and Li2CO3 for a very short annealing time, 4 h at 800°C. ...
Processing of gelatine coated composite scaffolds based on magnesium and strontium doped hydroxyapatite and yttria-stabilized zirconium oxide
(International Institute for the Science of Sintering, 2023)
Limited bone bank capacity and risk of infection are some of the main drawbacks of autologous and allogenic grafts, giving rise to synthetic materials for bone tissue implants. The aim of this study was to process and ...