Pretraživanje
Prikaz rezultata 11-20 od 23
Stress corrosion cracking resistance of aluminum alloy 7000 series after two-step aging / Otpornost aluminijumske legure serije 7000 prema naponskoj koroziji posle dvostepenog termičkog taloženja
(Association of the Chemical Engineers of Serbia, 2015)
The effect of one-step and a new (short) two-step aging process on the resistance to stress corrosion cracking of an aluminum alloy 7000 series was investigated, using slow strain rate test and fracture mechanics method. ...
Effect of AL2O3 particles on the toughness of hybrid composite with EVA matrix and UHMWPE fibersas reinforcement / Uticaj AL2O3 čestica na žilavost hibridnog kompozita sa EVA matricom ojačanog UHMWPE vlaknima
(Savez inženjera i tehničara Srbije, Beograd, 2018)
The aim of this paper is to investigate the mechanical properties of hybrid composites with the polymer matrix of the copolymer of ethylene and vinyl acetate (EVA), ultra high molecular weight polyethylene fibers (UHMWPE) ...
Ag+, Cu2+ and Zn2+ doped hydroxyapatite/tricalcium phosphate bioceramics: Influence of doping and sintering technique on mechanical properties
(University of Novi Sad, Faculty of Technology, 2018)
Green hydroxyapatite ceramics were obtained by cold uniaxial and isostatic pressing of hydrothermally synthesized powders, pure hydroxyapatite and hydroxyapatite doped with Ag+, Cu2+ and Zn2+ ions. The ceramics were ...
Synthesis of α-Al2O3 based foams with improved properties as catalyst carriers
(Institute of Metals and Technology, 2014)
This paper explores the possibility of synthesising catalyst supports with improved properties. Alumina foams were produced with the polymer replication technique. Representative high- and low-temperature sintering ceramics ...
Mechanical properties of alginate-liposomes-based beads with encapsulated resveratrol / Mehaničke karakteristike čestica alginat-lipozomi sa inkapsuliranim resveratrolom
(Faculty of Technology, Zvornik, 2015)
In this work mechanical behavior of four different formulations of alginate-based beads was
tested. The alginate beads were prepared by means of extrusion technique. As a model
encapsulated bioactive substance ...
Mechanical properties of two Al-Mg alloys manufactured by accumulative roll bonding (ARB) process
(Belgrade : Association of Metallurgical Engineers of Serbia (AMES), 2017)
The influence of alloying on the mechanical properties of AA5083 type Al-Mg
alloy sheets produced by accumulative roll bonding (ARB) process was studied.
Two investigated Al-Mg alloys: commercial AA5083 alloy with 4.2% ...
Mechanical properties of composites based on unsaturated polyester resins obtained by chemical recycling of poly(ethylene terephthalate) / Mehanička svojstva kompozita na bazi nezasićenih poliestarskih smola dobijenih hemijskom reciklažom poli(etilen-tereftalata)
(Association of Chemical Engineers of Serbia, 2013)
Composites based on unsaturated polyester (UPe) resins and fumed silica AEROSIL® RY 50, NY 50, RX 50 and NAX 50, as well as graphite, TiO2 or organically modified clay CLOISITE 30B were prepared in order to investigate the ...
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Characterization of tantalum coatings deposited using vacuum plasma spray process / Karakterizacija tantal prevlake deponovane vakuum plazma sprej procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2018)
Tantalum is a very popular material for the industry as a whole because of very important characteristics such as: high melting point, significant thermal and electrical conductivity, high toughness and resistance to ...
Age hardening potential of an Al-4.6 wt.% Mg alloy with Cu addition
(Belgrade : Institute of Technical Sciences of SASA, 2010)
The ageing behavior of an Al-4.6Mg-0.54Cu (in wt.%) alloy was studied after: (i) solution
treatment for 1h at 530°C, and (ii) annealing at 280°C for 3h. Both groups of the heat treated
specimens underwent further ...