Претраживање
Приказ резултата 21-30 од 38
A model for cross-referencing and calculating similarity of metal alloys
(Association of Metallurgical Engineers of Serbia, 2013)
This paper presents an innovative model for the comparison and cross- referencing of metal alloys, in order to determine their interchangeability in engineering, manufacturing and material sourcing. The model uses a large ...
Synthesis of novel wo3/zrsio4 catalysts for dehalogenation of halogenated hydrocarbons
(Savez inženjera metalurgije Srbije, Beograd, 2019)
This research aimed to develop a novel catalyst based on WO3/ZrSiO4 system for halogenated hydrocarbons processing. The production method of this catalyst involved extrusion and as such was simplified compared to thermo-chemical ...
The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys
(Savez inženjera metalurgije Srbije, Beograd, 2019)
The occurrence of abnormal grain growth (AGG) in AA5182 alloy during annealing imposes severe restrictions on processing parameters and deteriorates mechanical properties. In this work, we investigated the effect of chemical ...
Investigation of copper(i) sulphide leaching in oxidative hydrochloric acid solution
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Present work is focused on the copper (I) sulphide leaching with sodium chloride in hydrochloric acid solution and with introduction of gaseous oxygen. Chemical reactions of leaching and their thermodynamic probabilities ...
Estimation of phosphorus distribution ratio at the end of blowing in bof
(Metallurgical & Materials Engineering, 2021)
In integrated steel plants, the removal of phosphorous normally takes place during the primary basic oxygen furnace (BOF) steelmaking process. Phosphorous is usually introduced to the integrated steelmaking process through ...
The effect of calcinated hydroxyapatite and magnesium doped hydroxyapatite as fillers on the mechanical properties of a model bisgma/tegdma dental composite initially and after aging
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This study aimed to investigate the possibility of modifying model BisGMA/TEGDMA dental composite by substituting 10 wt. % of conventional glass fillers with bioactive fillers based on calcinated nanosized hydroxyapatite ...
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
Application of raw volcanic rock found in etna valley as an adsorbent of chromates, arsenates and selenates
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This paper aims to determine the potential of volcanic rock found in Etna valley as an adsorbent of heavy metals in anionic form (chromates, arsenates, and selenates). Characterization of the volcanic rock was done with ...
Synthesis of nife2o4 nanofibers by joint sol-gel and electrospinning technique
(Savez inženjera metalurgije Srbije, Beograd, 2018)
In this study, electrospinning combined with sol-gel technique is applied in order to produce magnetic nickel ferrite (Ni-ferrite) nanofibers. The prepared Ni-ferrite gel was mixed with poly(vinylpyrrolidone) (PVP) solution ...
Optimizing the thermal gradient and the pulling speed in a thermoplastic pultrusion process of pet/e glass fibers using finite element method
(Savez inženjera metalurgije Srbije, Beograd, 2018)
A thermoplastic pultrusion process was examined using commercial fiber roving of PET/E glass, to determine the optimum pulling speed and optimal zonal temperatures. Finite element analysis predicted heat transfer through ...