Pretraživanje
Prikaz rezultata 1-10 od 166
Prednosti zavarivanja trenjem sa mešanjem u odnosu na elektrolučno zavarivanje - zaštita zdravlja i životne sredine i bezbednost na radu / Advantages of friction stir welding over arc welding with respect to health and environmental protection and work safety
(Society for Structural Integrity and Life (DIVK), 2015)
U savremenoj industrijskoj proizvodnji, svaki proizvodni proces treba da bude ispitan u pogledu uticaja na životnu sredinu. Za svaku kompaniju koja investira u novi proces je od značaja pažljivo razmatranje HSE (Health, ...
Effect of corn straw pretreatment on efficiency of biogas production process: Computer simulation
(Institut za istrazivanja i projektovanja u privredi, 2020)
Anaerobic digestion is a natural process of organic material degradation by different kinds of microorganisms in the absence of oxygen. This process is used for industrial purpose to manage waste streams or to produce ...
Influence of defects on limit loads and integrity of the pipeline at hydropower plant 'Pirot'
(Society for Structural Integrity and Life, Institute for Material Testing, 2020)
Topic of this work is the integrity assessment of the pipeline section from hydropower plant Pirot. Crack-like defect size, maximum depth, is determined based on non-destructive evaluation - the largest crack depth is taken ...
Effect of the pH of artificial saliva on ion release from commercially pure titanium / Uticaj pH vrednosti veštačke pljuvačke na otpuštanje jona iz komercijalno čistog titana
(Faculty of Technology, Novi Sad, 2013)
Due to their excellent characteristics, such as chemical inertness, mechanical resistance, low Young's modulus, high corrosion resistance, and outstanding biocompatibility, titanium and its alloys are the most used metallic ...
Integrity assessment of regulation system pipeline elements in hydroelectric generating set a6 of hydro power plant 'Djerdap 1'
(Society for Structural Integrity and Life, Institute for Material Testing, 2016)
Vertical Kaplan turbines with nominal power of 176 MW manufactured in Russia are installed in 6 hydroelectric generating sets at hydro power plant 'Djerdap 1' (Kladovo, Serbia). Most of the components are made of materials ...
An overview of application of micromechanical models in ductile fracture analysis of welded joints
(Srpsko društvo za mehaniku, Beograd, 2020)
Fracture of welded joints has been an important research and industrial topic for a long time, having in mind the key role of welded joints in ensuring the safe operation and integrity of welded structures. This work ...
Strength design calculation of a horizontal pressure vessel / Kontrolni proračun čvrstoće horizontalne posude pod pritiskom
(Society for Structural Integrity and Life, Institute for Material Testing, 2013)
Standards SRPS M.E2.250-262 for calculation of pres-sure vessels have been replaced by SRPS EN 13445-3. This means that calculations of new equipment and check calculations of equipment in service are subjected to ordinance ...
Influence of encastering on thin-walled cantilever beams with u and z profiles on the magnitude of equivalent stress and deformation
(Society for Structural Integrity and Life, Institute for Material Testing, 2019)
The purpose of this work is to present analytical and numerical determination of equivalent stress and deformation of open section thin-walled U and Z cantilever beams loaded with torsion. This work can be divided into two ...
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Exploitation properties of ni-pd/al2o3 catalyst supported on ceramic foam
(Savez inženjera metalurgije Srbije, Beograd, 2015)
The goal of this research was to examine exploitation properties of Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam in the dry methane reforming. The catalyst was prepared by using aerosol method. Chloride precursors ...