Pretraživanje
Prikaz rezultata 1-10 od 49
Mechanical properties correlation to processing parameters for advanced alumina based refractories
(International Institute for the Science of Sintering, Beograd, 2012)
Alumina based refractories are usually used in metallurgical furnaces and their thermal shock resistance is of great importance. In order to improve thermal shock resistance and mechanical properties of alumina based ...
Effect of surface modified TiO2 nanoparticles on thermal, barrier and mechanical properties of long oil alkyd resin-based coatings
(Budapest Univ Technol & Econ, Budapest, 2015)
Novel soy alkyd-based nanocomposites (NCs) were prepared using TiO2 nanoparticles (NPs) surface modified with different gallates, and for the first time with imine obtained from 3,4-dihydroxybenzaldehyde and oleylamine ...
An Investigation into Mechanical Properties and Printability of Potential Substrates for Inkjet Printing of Orodispersible Films
(Pharmaceutics, 2021)
Inkjet printing is novel approach in drug manufacturing that enables dispensing precise volumes of ink onto substrates. Optimal substrate properties including suitable mechanical characteristic are recognized as crucial ...
Identification of low cycle fatigue parameters of high strength low-alloy (hsla) steel at room temperature
(Croatian Metallurgical Soc, Zagreb, 2014)
Low cycle fatigue test was performed in ambient atmosphere at room temperature. cycle loading of material, in case of High strength low-alloy steel, entails modifications of its properties and in this paper is therefore ...
Effect of AL2O3 particles on the toughness of hybrid composite with EVA matrix and UHMWPE fibersas reinforcement / Uticaj AL2O3 čestica na žilavost hibridnog kompozita sa EVA matricom ojačanog UHMWPE vlaknima
(Savez inženjera i tehničara Srbije, Beograd, 2018)
The aim of this paper is to investigate the mechanical properties of hybrid composites with the polymer matrix of the copolymer of ethylene and vinyl acetate (EVA), ultra high molecular weight polyethylene fibers (UHMWPE) ...
Ag+, Cu2+ and Zn2+ doped hydroxyapatite/tricalcium phosphate bioceramics: Influence of doping and sintering technique on mechanical properties
(University of Novi Sad, Faculty of Technology, 2018)
Green hydroxyapatite ceramics were obtained by cold uniaxial and isostatic pressing of hydrothermally synthesized powders, pure hydroxyapatite and hydroxyapatite doped with Ag+, Cu2+ and Zn2+ ions. The ceramics were ...
Experimental and numerical investigations of the critical values of J-integral for the steel of steam pipelines
(Elsevier Science Bv, Amsterdam, 2018)
Steel grade 14MoV6-3 is a low-carbon microalloyed steel with addition of chromium and molybdenum. This grade is designed mainly for power industry applications, withstanding operating at elevated temperatures.In this paper, ...
Stress corrosion cracking resistance of aluminum alloy 7000 series after two-step aging / Otpornost aluminijumske legure serije 7000 prema naponskoj koroziji posle dvostepenog termičkog taloženja
(Association of the Chemical Engineers of Serbia, 2015)
The effect of one-step and a new (short) two-step aging process on the resistance to stress corrosion cracking of an aluminum alloy 7000 series was investigated, using slow strain rate test and fracture mechanics method. ...
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (hsla) steel on low cycle fatigue
(Croatian Metallurgical Soc, Zagreb, 2014)
High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of ...
Microstructure and properties of silver based cadmium free electrical contact materials
(University of Belgrade, Technical Faculty, Bor, 2007)
The presented work covers part of experimental results of simultaneous study of microstructure, density, hardness and electrical conductivity of sintered electrical contact materials based of Ag- SnO2 with 8, 10 and 12 ...