Претраживање
Приказ резултата 31-40 од 146
Dynamic mechanical properties of aramid fabrics impregnated with multiwalled carbon nanotubes / Dinamičko mehanička svojstva aramidnih lamina impregnisanih sa višeslojnim ugljeničnim nanocevima
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
Carbon nanotubes (CNT) represent allotropes of carbon with a cylindrical nanostructure. In multiwalled carbon nanotubes (MWCNT), graphitic layers make up concentric tubes. The multiwalled nanotubes length in our research ...
Procedures for processing of copper secondary raw materials / Postupci prerade sekundarnih sirovina bakra
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
The technological procedures for copper secondary raw materials processing include two basic stages: pretreatment of the copper waste and its further metallurgical processing. For copper waste pretreatment technology, there ...
Modeling of the matrix porosity influence on the elastic properties of particulate biocomposites / Modeliranje uticaja matrične poroznosti na elastične osobine poroznih biokompozita
(University of Belgrade - Faculty of Mechanical Engineering, Belgrade, 2012)
For a wide range of engineering structures such as ceramics, porous shape memory alloys, foam-like structures and thermal spray deposits, porous materials have been used. Recently, porous biocomposites for the applications ...
Treatment of waste sulfuric acid copper electrolyte / Tretman otpadnog sumporno-kiselog elektrolita bakra
(Institut za rudarstvo i metalurgiju, Bor, 2014)
The aim of this paper was to investigate the possibility of using the copper anodes with high nickel content for electrolytic treatment of waste sulfuric acid copper electrolyte. Nickel content in each anode was about 10 ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
Microstructural characterization of glass-epoxy composites subjected to tensile testing / Mikromehanička karakterizacija staklo-epoksi kompozita izloženog zateznom opterećenju
(Faculty of Technology, Novi Sad, 2013)
The main objective of the research presented in this paper was to carry out a statistical-mechanical analysis concerning the tensile test of glass-epoxy composite materials in order to calculate their relevant tension ...
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
The effect of cooling rate of slag from primary copper production in the valorization of copper in the flotation process
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Technological procedure of slow cooling slag from primary copper production is applied in the purpose of copper recovery in the level of 98.5% to blister. This technological procedure is divided into two phases, first slow ...
Oxidation and erosion behaviour of SiC-HfC multilayered composite
(Univerzitet u Novom Sadu - Tehnološki fakultet, Novi Sad, 2014)
The fabrication of SiC-HfC ceramic composite via self-propagating high-temperature synthesis and simultaneous consolidation was investigated. Dense composite consisting of alternating layers of SiC and HfC was obtained by ...
Microstructural properties and cavitation behavior of hypereutectic Al-Si alloy obtained by rheocasting process / Mikrostrukturna svojstva i kavitaciono ponašanje nadeutektičke Al-Si legure dobijene reokasting postupkom
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The purpose of this study was to investigate possible application of AlSi alloy produced by rheocasting process in cavitation conditions. A rheocasting process was used to refine the as cast microstructure and improve the ...