Претраживање
Приказ резултата 21-30 од 1560
Optimization of the electrostatic droplet generation process for controlled microbead production: Single nozzle system / Optimizacija elektrostatičkog generisanja čestica u cilju kontrolisanja njihovih mikronskih veličina - sistem sa jednom mlaznicom
(Association of the Chemical Engineers of Serbia, 2006)
The aim of this study was to optimize the electrostatic extrusion process for producing small, spherical and uniform microbeads with different fluid viscosities by varying the operating parameters in very wide ranges. ...
Semi-interpenetrating polymer networks based on polyacrylamide and poly(itaconic acid) / Semi-interpenetrirajuće mreže na bazi poliakrilamida i poli(itakonske kiseline)
(Association of Chemical Engineers of Serbia, 2003)
The effect of pH and temperature on the equilibrium swelling properties of PIA/PAAm semi-IPNs were investigated.Semi-IPNs based on polyacrylamide (PAAm) and poly(itaconic acid) (PIA) were prepared by two different techniques, ...
The alternative methods of preparing wool for printing / Alternativni postupci pripreme vune za štampanje
(Union of Textile Engineers and Technicians of Serbia, Belgrade, 2002)
The adsorbable organohalogens (AOX) loading of effluent must be set against the high efficiency of chlorination in preparing wool for printing Therefore, there have been a number of research attempts to develop alternative ...
Surface characterization and properties of keratin fibers treated with low-temperature plasmas
(Polymer Surface Modification: Relevance to Adhesion, Volume 3, 2004)
The relation between shrink-resistance properties and surface changes (wettability, atomic chemical composition and topographical or morphological) induced by low-temperature plasmas (LTPs) has been studied in depth. For ...
A new technological solution for the manufacture of a borer for iron notch opening at the blast furnace plant / Primena aluminotermijskog postupka izrade i zavarivanja vrha burgija koje se koriste za otvoranje visoke peći tokom ispusta gvožđa
(Institut za istrazivanja i projektovanja u privredi, 2004)
A new technology for the manufacture of a borer by alumino-thermal method, system design for performing alumino-thermal reaction, as well as required quality of termite steel, is disclosed in this paper. In addition to ...
Photoacoustic study of CO2-laser coincidences with absorption of some organic solvent vapours
(Elsevier, Amsterdam, 2004)
Detection of specific molecules in the atmosphere is motivated by the need for monitoring the emission of industrial pollutants. CO2-laser photoacoustic (PA) spectroscopy was used here to obtain coincidence spectra of the ...
On the aqueous oxidation of polymetallic Cu-Zn-Pb gold-bearing sulphide ore in an autoclave
(CIM Bulletin, 2001)
The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions ...
The influence of zinc surface pretreatment on the adhesion of epoxy coating electrodeposited on hot-dip galvanized steel
(Elsevier Science Sa, Lausanne, 2007)
The adhesion and electrochemical properties of epoxy coatings electrodeposited on hot-dip galvanized steel with and without passive films were investigated during exposure to 3% NaCl. The passive films were formed in hot ...
Immobilization of penicillin acylase from Escherichia coli on commercial sepabeads EC-EP carrier / Imobilizacija penicilin-acilaze iz Escherichia coli na komercijalnom sepabeads nosaču
(Faculty of Technology, Novi Sad, 2007)
This paper describes the covalent immobilization of penicillin G acylase from Escherichia coli on sepabeads EC-EP, an epoxy-activated polymethacrylic carrier and kinetic properties of the immobilized enzyme. The selected ...
Deformation behaviour of welded stainless steel: Carbon steel sandwich sheet material / Deformaciono ponašanje zavarenog spoja sendvič lima nerđajući čelik - ugljenični čelik - nerđajući čelik
(Military Technical Institute, Belgrade, 2007)
Formability of welded austenitic stainless steel (321 type) - low carbon steel (1010 type) sandwich sheet material was tested. Gas tungsten arc welding (GTAW) and shield metal arc welding (SMAW) procedures were used. After ...