Претраживање
Приказ резултата 91-100 од 168
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
The effect of cooling rate of slag from primary copper production in the valorization of copper in the flotation process
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Technological procedure of slow cooling slag from primary copper production is applied in the purpose of copper recovery in the level of 98.5% to blister. This technological procedure is divided into two phases, first slow ...
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
Effect of process parameters on the phase transformation kinetics in copper-based alloys and composites
(Metallurgical & Materials Engineering, 2020)
Copper-based alloys and composites, owing to their convenient properties, are being considered essential materials in various industries. Since copper possesses an ability to develop high corrosion resistance, putting it ...
Time: Temperature superposition principle: Application of WLF equation in polymer analysis and composites / Princip superponiranja vremena i temperature - primena WLF jednačine za ispitivanje polimera i kompozita
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Polymers are the most studied viscoelastic material. The shorter times (high frequencies) corresponding to lower temperatures and long times (low frequencies) to high temperatures. This represents the quantitatively applied ...
Solvatochromism of N-aryl-phenylacetamides / Solvatohromizam N-aril-fenilacetamida
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Amide derivates are biologically active compounds and they are widely used in all spheres of life. Therefore, it is very important to know their physical-chemical properties. In this work the influence of characteristics ...
The effect of friction stirs welding speed on microstructure, mechanical properties and IGC of EN AW-5083 plates
(Advanced Technologies and Materials, 2019)
The aim of this work was to evaluate the influence of welding speed on microstructure, mechanical properties, as well as Intergranular corrosion (IGC) susceptibility of EN AW-5083 alloy welded using FSW. FSW was performed ...
Micromalting of triticale varieties NS Paun and Odisej
(Faculty of Technology, Novi Sad, 2018)
The objective of this study was to evaluate the possibility of application of two triticale varieties, NS Paun and Odisej, as partial substitutes for barley malt in wort production, based on the triticale analyses, ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
Treatment of dispersed iron-bearing raw materials and modeling of the protection systems against air-pollution
(Association of Metallurgical Engineers of Serbia, 2016)
Based on the analysis of the non-standard iron-bearing raw materials treatment process and the results of real composition measurements of the flue gas, the study of hazards by identification of harmful substances that ...