Претраживање
Приказ резултата 1-10 од 24
Integrated procedure for recycling and valorization of useful components from secondary raw materials based on hard metals
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Wide application of hard metals requires increased consumption of their constituents. Their high cost and scarcity impose the need for finding new, both ecologically and economically justified ways for their production. ...
Influence of the fabrication process of copper matrix composites on cavitation erosion resistance
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations ...
Some aspects of physical metallurgy of microalloyed steels
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Some aspects of deformation, precipitation, and recrystallization behavior in medium carbon V-microalloyed and low carbon Nb/Ti-microalloyed steels are presented in the paper. Changes in microstructure are explained together ...
Numerical simulation of temperature field in the vertical bridgman method crystal growth
(Savez inženjera metalurgije Srbije, Beograd, 2015)
The mathematical model for heat transfer during the Bridgeman crystal growth, using the finite element method and the obtained result are presented. Some modifications to the method were introduced in order to incorporate ...
Kinetics of barite reduction from refractory barite-sulphide ore
(Savez inženjera metalurgije Srbije, Beograd, 2016)
Refractory sulphide-barite ore was reduced with carbon in order to release lead, zinc, and copper sulphide from barite-pyrite base. Mineralogical investigations showed that due to the complex structural-textural relationships ...
Synthesis of nife2o4 nanofibers by joint sol-gel and electrospinning technique
(Savez inženjera metalurgije Srbije, Beograd, 2018)
In this study, electrospinning combined with sol-gel technique is applied in order to produce magnetic nickel ferrite (Ni-ferrite) nanofibers. The prepared Ni-ferrite gel was mixed with poly(vinylpyrrolidone) (PVP) solution ...
Application of raw volcanic rock found in etna valley as an adsorbent of chromates, arsenates and selenates
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This paper aims to determine the potential of volcanic rock found in Etna valley as an adsorbent of heavy metals in anionic form (chromates, arsenates, and selenates). Characterization of the volcanic rock was done with ...
The effect of calcinated hydroxyapatite and magnesium doped hydroxyapatite as fillers on the mechanical properties of a model bisgma/tegdma dental composite initially and after aging
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This study aimed to investigate the possibility of modifying model BisGMA/TEGDMA dental composite by substituting 10 wt. % of conventional glass fillers with bioactive fillers based on calcinated nanosized hydroxyapatite ...
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
The effect of cooling rate of slag from primary copper production in the valorization of copper in the flotation process
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Technological procedure of slow cooling slag from primary copper production is applied in the purpose of copper recovery in the level of 98.5% to blister. This technological procedure is divided into two phases, first slow ...