Претраживање
Приказ резултата 1-10 од 75
Investigation on the Adsorption of the Carbamate Pesticide Methomyl from Aqueous Solution using Modified Co-Beta Zeolite Particles
(International Institute for the Science of Sintering (IISS), 2023)
Adsorption of carbamate pesticide Methomyl by Co-Beta Zeolite particles prepared by wet ion-exchange method from aqueous solutions was studied. The effect of zeolite and pesticide concentrations, pH value, and sintering ...
Magnetic properties of ND Rich Melt-Spun ND-FE-B alloy
(International Institute for the Science of Sintering, Beograd, 2005)
As a part of these experimental investigations of melt-spun Nd-Fe-B alloy with Nd rich content in relation to Nd2Fe14B prepared by rapid quenching process for optimally selected cooling rate and heat treatment, the influence ...
Influence of the damage level during quenching on thermal shock behavior of low cement castable
(International Institute for the Science of Sintering, Beograd, 2010)
In the recent decades, the use of unshaped monolithic refractories has been increasing greatly because of their significant advantages over other shaped refractory bricks of the same class. A low cement high alumina castable ...
The effect of Y2O3 addition on thermal shock behavior of magnesium aluminate spinel
(International Institute for the Science of Sintering, Beograd, 2009)
The effect of yttria additive on the thermal shock behavior of magnesium aluminate spinel has been investigated. As a starting material we used spinel (MgAl2O4) obtained by the modified glycine nitrate procedure (MGNP). ...
Influence of Raster Angle on Tensile Properties of FDM Additively Manufactured Plates made from Carbon Reinforced PET-G Material
(Belgrade : Association for ETRAN Society, 2023)
Tensile properties of thin plate specimens made from short carbon fiberreinforced PET-G material are experimentally evaluated for various raster angles(printing directions). In additive manufacturing (AM), raster angle is ...
Effects of plastic deformation on the properties of W-Ni-Fe heavy alloys
(International Institute for the Science of Sintering, Beograd, 2001)
The effects of reduction in area due to rotary forging on the structure, physical and mechanical properties of 92,5W-5Ni-2,5Fe heavy alloy rods have been presented in this paper. Sintered rods (20mm) were rotary forged ...
Characterization of dispersion strengthened copper with 3wt%Al2O3 by mechanical alloying
(International Institute for the Science of Sintering, Beograd, 2004)
The copper matrix has been dispersion strengthened with 3wt.%Al2O3 by mechanical alloying. Commercial alumina powder with an average particle size of 0.75mm was used for alloying. The mechanical alloying process was performed ...
Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2017)
Mechanical shock of zircon based ceramic induced by cavitation erosion testing was investigated in this study. Several parameters were followed in order to determine level of material degradation during the cavitation ...
Mechanical properties of biomorphic silicon carbide ceramics
(International Institute for the Science of Sintering, Beograd, 2011)
Biomorphous β-SiC ceramics were produced from linden wood by impregnation with tetraethyl orthosilicate (TEOS), followed pyrolysis and high temperature treatment at 1580°C. Six specimen groups included charcoal and five ...
Cavitation resistance of the material PA 3200 GF produced by selective laser sintering
(International Institute for the Science of Sintering (IISS), 2023)
The present study focuses on the results of cavitation resistance research of samples obtained by the Selective Laser Sintering technology. The samples were made from polyamide powder reinforced with glass beads – PA 3200 ...