Претраживање
Приказ резултата 1-10 од 49
Development of Coated Electrodes with Solid Wire and Flux-Cored Alloyed Wire for Microalloyed Steel Welding
(MDPI, Basel, 2020)
In this paper, we will present our investigation of the quality of J55 microalloyed steel welds that were formed by a basic flux-cored wire electrodes that were of appropriate quality and alloyed with Ni and Mo. Based on ...
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Proučavanje uticaja metalnih vlakana na neka svojstva tehničkih pređa / Investigation of influence of metallic fibers on some properties of technical yarns
(Savez hemičara i tehnologa Srbije, 2000)
Ispitivana su neka mehanička i elektrofizička svojstva pređa formiranih od mešavine pamučnih i metalnih vlakana. Rezultati su upoređeni sa rezultatima dobijenim za pamučne pređe iste finoće. Registrovano je smanjenje ...
Influence of Novel SrTiO3/MnO2 Hybrid Nanoparticles on Poly(methyl methacrylate) Thermal and Mechanical Behavior
(MDPI, 2024)
While dental poly methyl methacrylate(PMMA) possesses distinctive qualities such as ease of fabrication, cost-effectiveness, and favorable physical and mechanical properties, these attributes alone are inadequate to impart ...
Titanium dioxide nanoparticles surface modified with imine as fillers for epoxy resin / Nanočestice titan-dioksida površinski modifikovane iminom kao punioci za epoksidnu smolu
(Univerzitet u Nišu - Tehnološki fakultet, Leskovac, 2018)
The surface of anatase TiO2 nanoparticles was modified with in situ synthesized imine, based on 3,4-dihydroxybenzaldehyde and octadecylamine. The modified TiO2 nanoparticles were investigated using FTIR and UV-Vis spectroscopy, ...
Structural, optical and mechanical characterization of PMMA- MXene composites functionalized with MEMO silane
(Taylor & Francis Group, 2022)
Processing and characterization of PMMA-MXene composites were investigated. γ-Methacryloxypropyltrimethoxy (MEMO) silane was used to modify the surface of MXenes and improve the compatibility between MXenes and the polymer. ...
Dynamic mechanical properties of aramid fabrics impregnated with multiwalled carbon nanotubes / Dinamičko mehanička svojstva aramidnih lamina impregnisanih sa višeslojnim ugljeničnim nanocevima
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
Carbon nanotubes (CNT) represent allotropes of carbon with a cylindrical nanostructure. In multiwalled carbon nanotubes (MWCNT), graphitic layers make up concentric tubes. The multiwalled nanotubes length in our research ...
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (hsla) steel on low cycle fatigue
(Croatian Metallurgical Soc, Zagreb, 2014)
High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of ...
Effect of surface modified TiO2 nanoparticles on thermal, barrier and mechanical properties of long oil alkyd resin-based coatings
(Budapest Univ Technol & Econ, Budapest, 2015)
Novel soy alkyd-based nanocomposites (NCs) were prepared using TiO2 nanoparticles (NPs) surface modified with different gallates, and for the first time with imine obtained from 3,4-dihydroxybenzaldehyde and oleylamine ...
Identification of low cycle fatigue parameters of high strength low-alloy (hsla) steel at room temperature
(Croatian Metallurgical Soc, Zagreb, 2014)
Low cycle fatigue test was performed in ambient atmosphere at room temperature. cycle loading of material, in case of High strength low-alloy steel, entails modifications of its properties and in this paper is therefore ...