Претраживање
Приказ резултата 31-40 од 166
Antimicrobial potential of triticale stillage after lactic acid fermentation with Lactobacillus fermentum PL-1 / Antimikrobni potencijal džibre tritikalea posle mlečno-kisele fermentacije pomoću Lactobacillus fermentum PL-1
(Faculty of Technology, Novi Sad, 2013)
This study is concerned with the testing of antimicrobial activity of triticale stillage obtained after lactic fermentation by Lactobacillus fermentum PL-1. The antimicrobial tests were performed using the disc-diffusion ...
Assessment of the integrity of welded pipes / Procena integriteta zavarenih cevi
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The subject of the paper is analysis of the integrity of welded pipes made of API J55 steel by high frequency contact welding (HF). Experimental research on the mechanical properties of the base material was conducted on ...
Dynamic mechanical properties of aramid fabrics impregnated with multiwalled carbon nanotubes / Dinamičko mehanička svojstva aramidnih lamina impregnisanih sa višeslojnim ugljeničnim nanocevima
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
Carbon nanotubes (CNT) represent allotropes of carbon with a cylindrical nanostructure. In multiwalled carbon nanotubes (MWCNT), graphitic layers make up concentric tubes. The multiwalled nanotubes length in our research ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
Polymer bonded magnetic composites based on Nd-Fe-B / Polimerni magnetni kompoziti na bazi Nd-Fe-B
(Inženjersko društvo za koroziju, Beograd, 2013)
Various types and contents of magnetic powder and polymer matrix induce different mechanical, magnetic, electrical and optical properties of final composite material. The strong influence of relatively small amounts of ...
Photocatalytic degradation of carbamate insecticides: Effect of different parameters / Fotokatalitička degradacija karbamatnih insekticida - efekti različitih parametara
(Institute of Pesticides and Environmental Protection, 2019)
Photocatalytic degradation of a model compound of the carbamate insecticide carbofuran in water was studied using polychromatic light and ZnO and TiO2 catalysts. The influence of operational parameters, such as reaction ...
Influence of the structural changes on cavitation resistance of Al18SiCuMg alloy produced by rheocasting process / Uticaj strukturnih promena na kavitacionu otpornost Al18SiCuMg legure proizvedene reokasting procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The influence of stirring speeds of 1000 and 1500 r/min on the microstructure of Al18SiCuMg alloy was investigated. The smaller size of Si particles of rheocast sample obtained by higher cooling rate and higher stirring ...
Leakage of an austenitic steel CO2 storage tank / Curenje posude za skladištenje CO2 od austenitnog čelika
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
After the occurrence of water droplets on the manhole outer wall of a storage tank for carbon dioxide, by detailed inspection, a net of cracks is detected in the manhole flange, close to the welded joint between the flange ...
Estimation of phosphorus distribution ratio at the end of blowing in bof
(Metallurgical & Materials Engineering, 2021)
In integrated steel plants, the removal of phosphorous normally takes place during the primary basic oxygen furnace (BOF) steelmaking process. Phosphorous is usually introduced to the integrated steelmaking process through ...
Assessment of the behaviour of fatigue loaded HSLA steel welded joint by applying fracture mechanics parameters / Procena ponašanja zavarenog spoja HSLA čelika opterećenog na zamor primenom parametara mehanike loma
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
From a fracture mechanics point of view on welded joints, it is assumed that the welded joint is pre-cracked such as that the fatigue life of the pre-cracked structure is then determined by the period of crack growth under ...