Pretraživanje
Prikaz rezultata 11-19 od 19
Impact of Alumina Particles on the Morphology and Mechanics of Hybrid Wood Plastic Composite Materials
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Hybrid composite panels of Wood-Plastic Composites (WPC) consisting of wood and poly (methyl methacrylate) (PMMA) were reinforced with alumina particles and made by "hot pressing" method. Alumina-based particles were made ...
Basalt-Polyester Hybrid Composite Materials for Demanding Wear Applications
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2020)
Basalt as a filler in a polymer-based composite material fulfils the demand of being natural, environment-friendly material for the production of various composite materials. The material could be used as protective layer ...
Photocatalytic Degradation of Bisphenol A with alpha-Fe2O3 Fibers and Particles
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Two-step synthesis of Fe2O3 particles, performed by precipitation from iron(III) chloride (FeCl3 center dot 6H(2)O) using ammonium hydroxide in first step and calcination at 400 and 700 degrees C during 4 h, provided Fe2O3 ...
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART II: Effect of Microstructure on Hardness, Electrical and Magnetic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
Nanostructured nickel-iron-tungsten alloys were produced by electrodeposition from an ammoniacal citrate bath. The tungsten content of the alloy ranged from 0.8 wt.% to 11 wt.%, and the crystal grain size of the FCC phase ...
Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent
(International Institute for the Science of Sintering (IISS), 2022)
In this study, the structure, morphology and composition of the synthesized magnetite/3D-printed wollastonite (3D_W/M) composite were characterized, and its adsorption performance with respect to As(V) and Cr(VI) were ...
An Experimental Study of Mechanical Properties and Heat Transfer of Acrylic Composites with Structural and Surface Modified Al2O3 Particles
(International Institute for the Science of Sintering (IISS), 2020)
Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat ...
TiO2 nanotubes film/FTO glass interface: Thermal treatment effects
(ETRAN, 2022)
Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal ...
Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles – Principal Component Analysis
(International Institute for the Science of Sintering, 2018)
This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...