Претраживање
Приказ резултата 1-10 од 22
Influence of picosecond laser pulses on the microstructure of austenitic materials
(Springer, New York, 2011)
We investigate samples of austenitic materials - stainless steel and iron-based superalloy - which are widely used at high temperatures and pressures. The samples were exposed to Nd(3+):YAG laser pulses with a wavelength ...
The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts
(Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac, 2015)
During the coal pulverizing, the working parts of the ventilation mill are being worn by the sand particles. For this reason, the working parts are usually protected with materials resistant to wear (hardfaced/thermal ...
Ag+, Cu2+ and Zn2+ doped hydroxyapatite/tricalcium phosphate bioceramics: Influence of doping and sintering technique on mechanical properties
(University of Novi Sad, Faculty of Technology, 2018)
Green hydroxyapatite ceramics were obtained by cold uniaxial and isostatic pressing of hydrothermally synthesized powders, pure hydroxyapatite and hydroxyapatite doped with Ag+, Cu2+ and Zn2+ ions. The ceramics were ...
Examination of the adhesion of polymer composite films based on Bis-GMA/TEGDMA on different metal substrates / Ispitivanje adhezije polimernih kompozitnih filmova na bazi Bis-GMA/TEGDMA na različitim metalnim podlogama
(Savez inženjera i tehničara Srbije, Beograd, 2018)
The subject of this study is the quantitative adhesion of a UV-curing composite film based on Bis-GMA (Bisphenol A glycidylmethacrylate) / TEGDMA (triethylene glycol dimethacrylate) as a matrix and particles doped with ...
Nimonic 263 microstructure and surface characterization after laser shock peening
(Croatian Metallurgical Soc, Zagreb, 2015)
The Laser Shock Peening (LSP) is applied to the surface of Nimonic 263 alloy. The changes in microstructure and surface topography are observed and analyzed by Scanning Electron Microscopy (SEM), profilometer and microhardness ...
Picosecond laser shock peening of base Nimonic 263 material and laser welded Nimonic 263 alloy / Mehanička obrada pikosekundnim laserom osnovnog materijala i zavarenih spojeva legure Nimonik 263
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2015)
Laser welding is a welding process with a high energy density and numerous advantages over conventional welding methods (narrow heat affected zone, lower heat input, less distortion, and the like.) Mechanical treatment ...
Development of Coated Electrodes with Solid Wire and Flux-Cored Alloyed Wire for Microalloyed Steel Welding
(MDPI, Basel, 2020)
In this paper, we will present our investigation of the quality of J55 microalloyed steel welds that were formed by a basic flux-cored wire electrodes that were of appropriate quality and alloyed with Ni and Mo. Based on ...
The advantages of using activated flux-cored wire compared to solid wire in the mag welding process from the aspect of metallurgical characteristics
(Croatian Metallurgical Soc, Zagreb, 2014)
This paper analyzes, from the metallurgical aspect, the quality of the new flux-cored wire intended for the MAG welding process in function of changes in shielding gas composition and changes in welding parameters. The ...
Characterisation of biomedical titanium layers deposited by a vacuum plasma spray process
(Materiali in Tehnologije, 2021)
In this paper we will describe the process of the deposition of thick layers of VPS-Ti coating, which is used as a bonding layer for the upper porous Ti coatings on implant substrates. In order to deposit the powder, we ...
INTEGRITY AND RISK ASSESSMENT OF RECONSTRUCTED STEAM LINE / PROCENA INTEGRITETA I RIZIKA REKONSTRUISANOG PAROVODA
(Society for Structural Integrity and Life (DIVK), 2023)
The integrity assessment of high pressure steam pipeline
primarily requires stress state determination, including not
only effects of working pressure and temperature, but also
all acting loads. Toward this aim, the ...