Претраживање
Приказ резултата 31-40 од 513
Optimization of the ball mill processing parameters in the fat filling production
(Savez hemijskih inženjera, Beograd, 2017)
The aim of this study was to determine the effect of the main milling variables, i.e., agitator shaft speed (50, 75 and 100%, which is 25, 37.5 and 50 rpm) and milling time (30, 45 and 60 min) on physical and sensory ...
Formation of a large-area monolayer of polystyrene film via the spin-coating method
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2018)
The self-assembly methods, an inexpensive and high throughput technique capable of producing nanostructure arrays, relies on the formation on a monolayer of self-assembled nanospheres. This paper reports on the formation ...
Lossless Compression of Vibration Signals on an Embedded Device Using a TDE Based Predictor
(Kaunas Univ Technology, Kaunas, 2016)
A lossless compression scheme for the data acquired from three-axial microelectromechanical (MEMS) accelerometer is presented. Time delay estimation (TDE) was applied in conjunction with differential pulse code modulation ...
Ultrasonic assisted arsenate adsorption on solvothermally synthesized calcite modified by goethite, alpha-MnO2 and goethite/alpha-MnO2
(Elsevier, Amsterdam, 2014)
A highly porous calcium carbonate (calcite; sorbent 1) was used as a support for modification with alpha-FeOOH (calcite/goethite; sorbent 2), alpha-MnO2 (calcite/alpha-MnO2; sorbent 3) and alpha-FeOOH/alpha-MnO2 ...
Impermeable layers in landfill design / Prilog projektovanju vodonepropusnih slojeva deponija
(Association of Chemical Engineers of Serbia, 2013)
Landfills are complex systems that could potentially contaminate the environment. This needs to be prevented by providing impermeability during the landfill design. In this aim, the related regulations should be followed ...
Effects of friction-welding parameters on the morphological properties of an al/cu bimetallic joint
(Inst Za Kovinske Materiale I In Tehnologie, Ljubjana, 2016)
The objective of this research is to consider the effects of certain parameters of the friction-welding process on the morphology of an aluminum/copper joint. The effect of the following parameters was monitored: the ...
Investigation of Possibility for Stabilization and Valorization of Electric Arc Furnace Dust and Glass From Electronic Waste
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
This paper presents investigation of possibility for electric arc furnace dust (EAFD) and electronic waste (e-waste) valorization trough stabilization process, in order to achieve concurrent management of these two serious ...
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART I: Effect of Synthesis Parameters on Chemical Composition, Microstructure and Morphology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
Kinetic and operational electrolysis parameters determine the polarization characteristics, electrodeposition current efficiency, morphology, chemical composition and microstructure of nickel/iron/tungsten alloy deposits. ...
Influence of Synthesis Parameters on Structure of 1-D TiO2 nanostructures
(Belgrade : Serbian Ceramic Society, 2015)
The influence of electrochemical conditions and the heat treatment on the crystal structure and the microstructure evolution of TiO2 based nanotubes synthesized by the self-ordering anodization process is investigated in ...
Decolorization of anthraquinonic dyes from textile effluent using horseradish peroxidase: Optimization and kinetic study
(Hindawi Limited, 2015)
Two anthraquinonic dyes, C.I. Acid Blue 225 and C.I. Acid Violet 109, were used as models to explore the feasibility of using the horseradish peroxidase enzyme (HRP) in the practical decolorization of anthraquinonic dyes ...