Претраживање
Приказ резултата 1-10 од 22
Influence of picosecond laser pulses on the microstructure of austenitic materials
(Springer, New York, 2011)
We investigate samples of austenitic materials - stainless steel and iron-based superalloy - which are widely used at high temperatures and pressures. The samples were exposed to Nd(3+):YAG laser pulses with a wavelength ...
Ag+, Cu2+ and Zn2+ doped hydroxyapatite/tricalcium phosphate bioceramics: Influence of doping and sintering technique on mechanical properties
(University of Novi Sad, Faculty of Technology, 2018)
Green hydroxyapatite ceramics were obtained by cold uniaxial and isostatic pressing of hydrothermally synthesized powders, pure hydroxyapatite and hydroxyapatite doped with Ag+, Cu2+ and Zn2+ ions. The ceramics were ...
Nimonic 263 microstructure and surface characterization after laser shock peening
(Croatian Metallurgical Soc, Zagreb, 2015)
The Laser Shock Peening (LSP) is applied to the surface of Nimonic 263 alloy. The changes in microstructure and surface topography are observed and analyzed by Scanning Electron Microscopy (SEM), profilometer and microhardness ...
Examination of the adhesion of polymer composite films based on Bis-GMA/TEGDMA on different metal substrates / Ispitivanje adhezije polimernih kompozitnih filmova na bazi Bis-GMA/TEGDMA na različitim metalnim podlogama
(Savez inženjera i tehničara Srbije, Beograd, 2018)
The subject of this study is the quantitative adhesion of a UV-curing composite film based on Bis-GMA (Bisphenol A glycidylmethacrylate) / TEGDMA (triethylene glycol dimethacrylate) as a matrix and particles doped with ...
The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts
(Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac, 2015)
During the coal pulverizing, the working parts of the ventilation mill are being worn by the sand particles. For this reason, the working parts are usually protected with materials resistant to wear (hardfaced/thermal ...
Examination of mechanical properties of acrilyc composite materials with different AL2O3 reinforcement by brazil test / Ispitivanje mehaničkih svojstava akrilatnih kompozitnih materijala sa različitim AL2O3 ojačanjima brazilskim testom
(Savez inženjera i tehničara Srbije, Beograd, 2019)
Composite materials based on UV-curing acrylates and various alumina-based reinforcements represent material that is suitable for the use in dentistry, but also in other areas. Composites were made using four different ...
Picosecond laser shock peening of base Nimonic 263 material and laser welded Nimonic 263 alloy / Mehanička obrada pikosekundnim laserom osnovnog materijala i zavarenih spojeva legure Nimonik 263
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2015)
Laser welding is a welding process with a high energy density and numerous advantages over conventional welding methods (narrow heat affected zone, lower heat input, less distortion, and the like.) Mechanical treatment ...
The effect of CaO and MgO addition and cooling rate on stability of slag obtained after jarosite and neutral leaching residue treatment in the Waelz process
(Oficyna Wydawnicza Politechniki Wroclawskiej, Wroclaw, 2018)
Jarosite and neutral leaching residue (NLR) are the greatest environmental problems of hydrometallurgical zinc production due to their high quantity and hazardous content. Pyrometallurgical processes, such as the Waelz ...
Mechanical and structural characteristics of atmospheric plasma-sprayed multifunctional tio2 coatings
(Materiali in Tehnologije, 2020)
Titanium dioxide (TiO2) is a multifunctional oxide that is an interesting material for many technological applications. This paper presents the mechanical properties and microstructure of TiO2 coatings resistant to dry ...
Characterisation of biomedical titanium layers deposited by a vacuum plasma spray process
(Materiali in Tehnologije, 2021)
In this paper we will describe the process of the deposition of thick layers of VPS-Ti coating, which is used as a bonding layer for the upper porous Ti coatings on implant substrates. In order to deposit the powder, we ...