TY  - JOUR
AU  - Zemljak, Olivera
AU  - Golić Luković, Danijela
AU  - Počuča-Nešić, Milica
AU  - Dapčević, Aleksandra
AU  - Šenjug, Pavla
AU  - Pajić, Damir
AU  - Radošević, Tina
AU  - Branković, Goran
AU  - Branković, Zorica
PY  - 2022
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5204
AB  - Yttrium manganite, YMnO3, was doped with different concentrations of titanium (x = 0, 0.04, 0.08, 0.10, 0.15, 0.20) in order to improve the microstructural and multiferroic properties. The powders were prepared using sol-gel polymerization complex method from citrate precursors. Depending on the titanium concentration, the hexagonal structure and/or the rhombohedral superstructure are present in the sintered samples. The YMn1–xTixO3+δ (x = 0.10, 0.15, 0.20) ceramic samples showed significantly reduced density of microcracks, and of inter- and intragranular pores, and relative densities greater than 90%. The structural parameters for YMn1–xTixO3+δ (x = 0, 0.10, 0.15) were correlated with the results of magnetic and ferroelectric measurements. The most of titanium-doped samples showed a reduction of the leakage current density in comparison with undoped YMnO3, and their ferroelectric responses were slightly improved. The modifications in structural arrangement resulted in partial suppression of ideal antiferromagnetic ordering visible through decrease of the Néel temperature and Weiss parameter, as well as the appearance of weak ferromagnetism and increase of magnetization (especially, in samples x = 0.08, 0.10, 0.15). These changes in physical quantities most likely originated from incorporation of the uncompensated magnetic moments and possible spin canting induced by enhanced symmetry break of the superexchange bridges.
PB  - Springer
T2  - Journal of Sol-Gel Science and Technology
T1  - Titanium doped yttrium manganite: improvement of microstructural properties and peculiarities of multiferroic properties
EP  - 819
IS  - 3
SP  - 807
VL  - 103
DO  - 10.1007/s10971-022-05872-3
ER  - 

@article{
author = "Zemljak, Olivera and Golić Luković, Danijela and Počuča-Nešić, Milica and Dapčević, Aleksandra and Šenjug, Pavla and Pajić, Damir and Radošević, Tina and Branković, Goran and Branković, Zorica",
year = "2022",
abstract = "Yttrium manganite, YMnO3, was doped with different concentrations of titanium (x = 0, 0.04, 0.08, 0.10, 0.15, 0.20) in order to improve the microstructural and multiferroic properties. The powders were prepared using sol-gel polymerization complex method from citrate precursors. Depending on the titanium concentration, the hexagonal structure and/or the rhombohedral superstructure are present in the sintered samples. The YMn1–xTixO3+δ (x = 0.10, 0.15, 0.20) ceramic samples showed significantly reduced density of microcracks, and of inter- and intragranular pores, and relative densities greater than 90%. The structural parameters for YMn1–xTixO3+δ (x = 0, 0.10, 0.15) were correlated with the results of magnetic and ferroelectric measurements. The most of titanium-doped samples showed a reduction of the leakage current density in comparison with undoped YMnO3, and their ferroelectric responses were slightly improved. The modifications in structural arrangement resulted in partial suppression of ideal antiferromagnetic ordering visible through decrease of the Néel temperature and Weiss parameter, as well as the appearance of weak ferromagnetism and increase of magnetization (especially, in samples x = 0.08, 0.10, 0.15). These changes in physical quantities most likely originated from incorporation of the uncompensated magnetic moments and possible spin canting induced by enhanced symmetry break of the superexchange bridges.",
publisher = "Springer",
journal = "Journal of Sol-Gel Science and Technology",
title = "Titanium doped yttrium manganite: improvement of microstructural properties and peculiarities of multiferroic properties",
pages = "819-807",
number = "3",
volume = "103",
doi = "10.1007/s10971-022-05872-3"
}

Zemljak, O., Golić Luković, D., Počuča-Nešić, M., Dapčević, A., Šenjug, P., Pajić, D., Radošević, T., Branković, G.,& Branković, Z.. (2022). Titanium doped yttrium manganite: improvement of microstructural properties and peculiarities of multiferroic properties. in Journal of Sol-Gel Science and Technology
Springer., 103(3), 807-819.
https://doi.org/10.1007/s10971-022-05872-3

Zemljak O, Golić Luković D, Počuča-Nešić M, Dapčević A, Šenjug P, Pajić D, Radošević T, Branković G, Branković Z. Titanium doped yttrium manganite: improvement of microstructural properties and peculiarities of multiferroic properties. in Journal of Sol-Gel Science and Technology. 2022;103(3):807-819.
doi:10.1007/s10971-022-05872-3 .

Zemljak, Olivera, Golić Luković, Danijela, Počuča-Nešić, Milica, Dapčević, Aleksandra, Šenjug, Pavla, Pajić, Damir, Radošević, Tina, Branković, Goran, Branković, Zorica, "Titanium doped yttrium manganite: improvement of microstructural properties and peculiarities of multiferroic properties" in Journal of Sol-Gel Science and Technology, 103, no. 3 (2022):807-819,
https://doi.org/10.1007/s10971-022-05872-3 . .

TY  - JOUR
AU  - Vukašinović, Jelena
AU  - Počuča-Nešić, Milica
AU  - Luković-Golić, Danijela
AU  - Ribić, Vesna
AU  - Branković, Zorica
AU  - Savić, Slavica M.
AU  - Dapčević, Aleksandra
AU  - Bernik, Slavko
AU  - Podlogar, Matejka
AU  - Kocen, Matej
AU  - Rapljenović, Željko
AU  - Ivek, Tomislav
AU  - Lazović, Vladimir
AU  - Dojčinović, Biljana
AU  - Branković, Goran
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4403
AB  - Antimony doped barium-stannate dense ceramic materials were synthesized using spark plasma sintering technique out of mechanically activated precursor powders. The influence of various Sb concentrations (x = 0.00 - 0.10) on properties of BaSn1-xSbxO3 ceramics was investigated. Relative densities of prepared samples were in the range of (79-96) %. TEM analysis revealed the presence of many dislocations in undoped BaSnO3, and their significant reduction upon doping with Sb. All samples except BaSn0.92Sb0.08O3 exhibit non-linear I-U characteristic, typical for semiconductors with potential barrier at grain boundaries. Low angle grain boundaries found only in BaSn0.92Sb0.08O3 caused the loss of potential barrier at grain boundaries which was confirmed by AC impedance spectroscopy measurements. Consequently, BaSn0.92Sb0.08O3 showed the lowest electrical resistivity and linear I-U characteristic. UV-vis analysis confirmed the increasing of band gap (Burstein-Moss shift) values in all doped samples.
PB  - Elsevier Sci Ltd, Oxford
T2  - Journal of the European Ceramic Society
T1  - The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics
EP  - 5575
IS  - 15
SP  - 5566
VL  - 40
DO  - 10.1016/j.jeurceramsoc.2020.06.062
ER  - 

@article{
author = "Vukašinović, Jelena and Počuča-Nešić, Milica and Luković-Golić, Danijela and Ribić, Vesna and Branković, Zorica and Savić, Slavica M. and Dapčević, Aleksandra and Bernik, Slavko and Podlogar, Matejka and Kocen, Matej and Rapljenović, Željko and Ivek, Tomislav and Lazović, Vladimir and Dojčinović, Biljana and Branković, Goran",
year = "2020",
abstract = "Antimony doped barium-stannate dense ceramic materials were synthesized using spark plasma sintering technique out of mechanically activated precursor powders. The influence of various Sb concentrations (x = 0.00 - 0.10) on properties of BaSn1-xSbxO3 ceramics was investigated. Relative densities of prepared samples were in the range of (79-96) %. TEM analysis revealed the presence of many dislocations in undoped BaSnO3, and their significant reduction upon doping with Sb. All samples except BaSn0.92Sb0.08O3 exhibit non-linear I-U characteristic, typical for semiconductors with potential barrier at grain boundaries. Low angle grain boundaries found only in BaSn0.92Sb0.08O3 caused the loss of potential barrier at grain boundaries which was confirmed by AC impedance spectroscopy measurements. Consequently, BaSn0.92Sb0.08O3 showed the lowest electrical resistivity and linear I-U characteristic. UV-vis analysis confirmed the increasing of band gap (Burstein-Moss shift) values in all doped samples.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Journal of the European Ceramic Society",
title = "The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics",
pages = "5575-5566",
number = "15",
volume = "40",
doi = "10.1016/j.jeurceramsoc.2020.06.062"
}

Vukašinović, J., Počuča-Nešić, M., Luković-Golić, D., Ribić, V., Branković, Z., Savić, S. M., Dapčević, A., Bernik, S., Podlogar, M., Kocen, M., Rapljenović, Ž., Ivek, T., Lazović, V., Dojčinović, B.,& Branković, G.. (2020). The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics. in Journal of the European Ceramic Society
Elsevier Sci Ltd, Oxford., 40(15), 5566-5575.
https://doi.org/10.1016/j.jeurceramsoc.2020.06.062

Vukašinović J, Počuča-Nešić M, Luković-Golić D, Ribić V, Branković Z, Savić SM, Dapčević A, Bernik S, Podlogar M, Kocen M, Rapljenović Ž, Ivek T, Lazović V, Dojčinović B, Branković G. The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics. in Journal of the European Ceramic Society. 2020;40(15):5566-5575.
doi:10.1016/j.jeurceramsoc.2020.06.062 .

Vukašinović, Jelena, Počuča-Nešić, Milica, Luković-Golić, Danijela, Ribić, Vesna, Branković, Zorica, Savić, Slavica M., Dapčević, Aleksandra, Bernik, Slavko, Podlogar, Matejka, Kocen, Matej, Rapljenović, Željko, Ivek, Tomislav, Lazović, Vladimir, Dojčinović, Biljana, Branković, Goran, "The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics" in Journal of the European Ceramic Society, 40, no. 15 (2020):5566-5575,
https://doi.org/10.1016/j.jeurceramsoc.2020.06.062 . .

TY  - JOUR
AU  - Vasiljević, Zorka Ž.
AU  - Dojčinović, Milena
AU  - Vujančević, Jelena
AU  - Janković-Častvan, Ivona
AU  - Ognjanović, M.
AU  - Tadić, N.
AU  - Stojadinović, S.
AU  - Branković, Goran
AU  - Nikolić, Maria Vesna
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4401
AB  - The aim of this work was to synthesize semiconducting oxide nanoparticles using a simple method with low production cost to be applied in natural sunlight for photocatalytic degradation of pollutants in waste water. Iron titanate (Fe2TiO5) nanoparticles with an orthorhombic structure were successfully synthesized using a modified sol-gel method and calcination at 750 degrees C. The as-prepared Fe2TiO5 nanoparticles exhibited a moderate specific surface area. The mesoporous Fe2TiO5 nanoparticles possessed strong absorption in the visible-light region and the band gap was estimated to be around 2.16 eV. The photocatalytic activity was evaluated by the degradation of methylene blue under natural sunlight. The effect of parameters such as the amount of catalyst, initial concentration of the dye and pH of the dye solution on the removal efficiency of methylene blue was investigated. Fe2TiO5 showed high degradation efficiency in a strong alkaline medium that can be the result of the facilitated formation of OH radicals due to an increased concentration of hydroxyl ions.
PB  - Royal Soc, London
T2  - Royal Society Open Science
T1  - Photocatalytic degradation of methylene blue under natural sunlight using iron titanate nanoparticles prepared by a modified sol-gel method
IS  - 9
VL  - 7
DO  - 10.1098/rsos.200708
ER  - 

@article{
author = "Vasiljević, Zorka Ž. and Dojčinović, Milena and Vujančević, Jelena and Janković-Častvan, Ivona and Ognjanović, M. and Tadić, N. and Stojadinović, S. and Branković, Goran and Nikolić, Maria Vesna",
year = "2020",
abstract = "The aim of this work was to synthesize semiconducting oxide nanoparticles using a simple method with low production cost to be applied in natural sunlight for photocatalytic degradation of pollutants in waste water. Iron titanate (Fe2TiO5) nanoparticles with an orthorhombic structure were successfully synthesized using a modified sol-gel method and calcination at 750 degrees C. The as-prepared Fe2TiO5 nanoparticles exhibited a moderate specific surface area. The mesoporous Fe2TiO5 nanoparticles possessed strong absorption in the visible-light region and the band gap was estimated to be around 2.16 eV. The photocatalytic activity was evaluated by the degradation of methylene blue under natural sunlight. The effect of parameters such as the amount of catalyst, initial concentration of the dye and pH of the dye solution on the removal efficiency of methylene blue was investigated. Fe2TiO5 showed high degradation efficiency in a strong alkaline medium that can be the result of the facilitated formation of OH radicals due to an increased concentration of hydroxyl ions.",
publisher = "Royal Soc, London",
journal = "Royal Society Open Science",
title = "Photocatalytic degradation of methylene blue under natural sunlight using iron titanate nanoparticles prepared by a modified sol-gel method",
number = "9",
volume = "7",
doi = "10.1098/rsos.200708"
}

Vasiljević, Z. Ž., Dojčinović, M., Vujančević, J., Janković-Častvan, I., Ognjanović, M., Tadić, N., Stojadinović, S., Branković, G.,& Nikolić, M. V.. (2020). Photocatalytic degradation of methylene blue under natural sunlight using iron titanate nanoparticles prepared by a modified sol-gel method. in Royal Society Open Science
Royal Soc, London., 7(9).
https://doi.org/10.1098/rsos.200708

Vasiljević ZŽ, Dojčinović M, Vujančević J, Janković-Častvan I, Ognjanović M, Tadić N, Stojadinović S, Branković G, Nikolić MV. Photocatalytic degradation of methylene blue under natural sunlight using iron titanate nanoparticles prepared by a modified sol-gel method. in Royal Society Open Science. 2020;7(9).
doi:10.1098/rsos.200708 .

Vasiljević, Zorka Ž., Dojčinović, Milena, Vujančević, Jelena, Janković-Častvan, Ivona, Ognjanović, M., Tadić, N., Stojadinović, S., Branković, Goran, Nikolić, Maria Vesna, "Photocatalytic degradation of methylene blue under natural sunlight using iron titanate nanoparticles prepared by a modified sol-gel method" in Royal Society Open Science, 7, no. 9 (2020),
https://doi.org/10.1098/rsos.200708 . .

TY  - JOUR
AU  - Luković-Golić, Danijela
AU  - Radojković, Aleksandar
AU  - Dapčević, Aleksandra
AU  - Pajić, Damir
AU  - Dragović, Jure
AU  - Torić, Filip
AU  - Ćirković, Jovana
AU  - Branković, Goran
AU  - Branković, Zorica
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4079
AB  - Bismuth ferrite, BiFeO3, was doped with a wide range of concentrations (0-30%) of Gd in order to investigate structural, ferroelectric, and magnetic properties and their correlation. Powder samples of Bi1-xGdxFeO3 (x = 0.00-0.30) were prepared using the hydro-evaporation synthesis method. Sintering process at 870 degrees C for 6 h of as-prepared, Gd doped BiFeO3 powders resulted in ceramic samples with relative densities in the range of (74-86) %. XRD analysis revealed that Bi1-xGdxFeO3 samples (x = 0.00-0.09) crystallized in rhombohedral phase; Bi1-xGdxFeO3 samples (x = 0.10-0.20) contained both rhombohedral and orthorhombic phases, while Bi1-xGdxFeO3 (x = 0.30) sample contained only the orthorhombic phase. The structural parameters obtained after Rietveld refinement for single-phase Bi1-xGdxFeO3 ceramic samples and microstructure image analysis were correlated with the results of ferroelectric and magnetic measurements. Bi1-xGdxFeO3 (x = 0.0625, 0.075, 0.09) samples showed improved ferroelectric properties and reduced leakage current density in comparison with undoped BiFeO3. Gradual increase in Gd content in BiFeO3 led to enhanced magnetic responses and weak ferromagnetic behavior.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Change in structural, ferroelectric, and magnetic properties of bismuth ferrite induced by doping with gadolinium
EP  - 19165
IS  - 15
SP  - 19158
VL  - 45
DO  - 10.1016/j.ceramint.2019.06.162
ER  - 

@article{
author = "Luković-Golić, Danijela and Radojković, Aleksandar and Dapčević, Aleksandra and Pajić, Damir and Dragović, Jure and Torić, Filip and Ćirković, Jovana and Branković, Goran and Branković, Zorica",
year = "2019",
abstract = "Bismuth ferrite, BiFeO3, was doped with a wide range of concentrations (0-30%) of Gd in order to investigate structural, ferroelectric, and magnetic properties and their correlation. Powder samples of Bi1-xGdxFeO3 (x = 0.00-0.30) were prepared using the hydro-evaporation synthesis method. Sintering process at 870 degrees C for 6 h of as-prepared, Gd doped BiFeO3 powders resulted in ceramic samples with relative densities in the range of (74-86) %. XRD analysis revealed that Bi1-xGdxFeO3 samples (x = 0.00-0.09) crystallized in rhombohedral phase; Bi1-xGdxFeO3 samples (x = 0.10-0.20) contained both rhombohedral and orthorhombic phases, while Bi1-xGdxFeO3 (x = 0.30) sample contained only the orthorhombic phase. The structural parameters obtained after Rietveld refinement for single-phase Bi1-xGdxFeO3 ceramic samples and microstructure image analysis were correlated with the results of ferroelectric and magnetic measurements. Bi1-xGdxFeO3 (x = 0.0625, 0.075, 0.09) samples showed improved ferroelectric properties and reduced leakage current density in comparison with undoped BiFeO3. Gradual increase in Gd content in BiFeO3 led to enhanced magnetic responses and weak ferromagnetic behavior.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Change in structural, ferroelectric, and magnetic properties of bismuth ferrite induced by doping with gadolinium",
pages = "19165-19158",
number = "15",
volume = "45",
doi = "10.1016/j.ceramint.2019.06.162"
}

Luković-Golić, D., Radojković, A., Dapčević, A., Pajić, D., Dragović, J., Torić, F., Ćirković, J., Branković, G.,& Branković, Z.. (2019). Change in structural, ferroelectric, and magnetic properties of bismuth ferrite induced by doping with gadolinium. in Ceramics International
Elsevier Sci Ltd, Oxford., 45(15), 19158-19165.
https://doi.org/10.1016/j.ceramint.2019.06.162

Luković-Golić D, Radojković A, Dapčević A, Pajić D, Dragović J, Torić F, Ćirković J, Branković G, Branković Z. Change in structural, ferroelectric, and magnetic properties of bismuth ferrite induced by doping with gadolinium. in Ceramics International. 2019;45(15):19158-19165.
doi:10.1016/j.ceramint.2019.06.162 .

Luković-Golić, Danijela, Radojković, Aleksandar, Dapčević, Aleksandra, Pajić, Damir, Dragović, Jure, Torić, Filip, Ćirković, Jovana, Branković, Goran, Branković, Zorica, "Change in structural, ferroelectric, and magnetic properties of bismuth ferrite induced by doping with gadolinium" in Ceramics International, 45, no. 15 (2019):19158-19165,
https://doi.org/10.1016/j.ceramint.2019.06.162 . .

TY  - JOUR
AU  - Pocuca-Nesić, Milica
AU  - Marinković-Stanojević, Zorica
AU  - Cotić-Smole, Patricia
AU  - Dapčević, Aleksandra
AU  - Tasić, Nikola
AU  - Branković, Goran
AU  - Branković, Zorica
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4138
AB  - Yttrium manganite (YMnO3) is widely investigated multiferroic material with potential use in many technological applications. In this paper, we report on the preparation and characterization of multiferroic hexagonal YMnO3 ceramics obtained by chemical synthesis route. Precursor powders were prepared by the polymerizable complex method from citrate precursors. After calcination at 900 degrees C the powders contained mixture of Y-Mn-O phases which were further sintered at different temperatures. XRD analysis revealed that sintering at 1400 degrees C resulted in the formation of pure hexagonal YMnO3. Density of the obtained ceramics was 96 %TD. The ceramic samples proved to have multiferroic properties - they are antiferromagnetic below 42 K with linear dependence of magnetization as a function of applied magnetic field. The ferroelectric measurements performed at room temperature showed remanent polarization of 0.21 mu C/cm(2) and the coercive field of 6.0 kV/cm for the YMnO3 sample sintered at 1400 degrees C. The magnetization curves measured at 2 and 5 K for the powder samples calcined at 900 degrees C and ceramic samples sintered at 1300 degrees C exhibited a hysteresis loop due to a small concentration of Mn3O4 in the samples.
PB  - Univerzitet u Novom Sadu - Tehnološki fakultet, Novi Sad
T2  - Processing and Application of Ceramics
T1  - Processing and properties of pure antiferromagnetic h-YMnO3
EP  - 434
IS  - 4
SP  - 427
VL  - 13
DO  - 10.2298/PAC1904427P
ER  - 

@article{
author = "Pocuca-Nesić, Milica and Marinković-Stanojević, Zorica and Cotić-Smole, Patricia and Dapčević, Aleksandra and Tasić, Nikola and Branković, Goran and Branković, Zorica",
year = "2019",
abstract = "Yttrium manganite (YMnO3) is widely investigated multiferroic material with potential use in many technological applications. In this paper, we report on the preparation and characterization of multiferroic hexagonal YMnO3 ceramics obtained by chemical synthesis route. Precursor powders were prepared by the polymerizable complex method from citrate precursors. After calcination at 900 degrees C the powders contained mixture of Y-Mn-O phases which were further sintered at different temperatures. XRD analysis revealed that sintering at 1400 degrees C resulted in the formation of pure hexagonal YMnO3. Density of the obtained ceramics was 96 %TD. The ceramic samples proved to have multiferroic properties - they are antiferromagnetic below 42 K with linear dependence of magnetization as a function of applied magnetic field. The ferroelectric measurements performed at room temperature showed remanent polarization of 0.21 mu C/cm(2) and the coercive field of 6.0 kV/cm for the YMnO3 sample sintered at 1400 degrees C. The magnetization curves measured at 2 and 5 K for the powder samples calcined at 900 degrees C and ceramic samples sintered at 1300 degrees C exhibited a hysteresis loop due to a small concentration of Mn3O4 in the samples.",
publisher = "Univerzitet u Novom Sadu - Tehnološki fakultet, Novi Sad",
journal = "Processing and Application of Ceramics",
title = "Processing and properties of pure antiferromagnetic h-YMnO3",
pages = "434-427",
number = "4",
volume = "13",
doi = "10.2298/PAC1904427P"
}

Pocuca-Nesić, M., Marinković-Stanojević, Z., Cotić-Smole, P., Dapčević, A., Tasić, N., Branković, G.,& Branković, Z.. (2019). Processing and properties of pure antiferromagnetic h-YMnO3. in Processing and Application of Ceramics
Univerzitet u Novom Sadu - Tehnološki fakultet, Novi Sad., 13(4), 427-434.
https://doi.org/10.2298/PAC1904427P

Pocuca-Nesić M, Marinković-Stanojević Z, Cotić-Smole P, Dapčević A, Tasić N, Branković G, Branković Z. Processing and properties of pure antiferromagnetic h-YMnO3. in Processing and Application of Ceramics. 2019;13(4):427-434.
doi:10.2298/PAC1904427P .

Pocuca-Nesić, Milica, Marinković-Stanojević, Zorica, Cotić-Smole, Patricia, Dapčević, Aleksandra, Tasić, Nikola, Branković, Goran, Branković, Zorica, "Processing and properties of pure antiferromagnetic h-YMnO3" in Processing and Application of Ceramics, 13, no. 4 (2019):427-434,
https://doi.org/10.2298/PAC1904427P . .

TY  - JOUR
AU  - Simović, Bojana
AU  - Dapčević, Aleksandra
AU  - Zdravković, J.
AU  - Tasić, Nikola
AU  - Kovač, S.
AU  - Krstić, Jugoslav
AU  - Branković, Goran
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4321
AB  - In this work, nine products were prepared by modifying the experimental conditions (6, 12 and 18 hat 110, 135 and 160 degrees C) of hydrothermal treatment of starting nanoanatase in significantly less concentrated alkaline medium than usual in order to obtain a pure titanate phase. The nanocrystalline samples were characterized by XRPD, FESEM, HRTEM/SAED, EDS, TG, FT-IR, UV-Vis and BET analyses. The results revealed that the structure, texture, morphology and band gap energy of samples strongly depend on conditions of hydrothermal treatment. The intensification of hydrothermal treatment significantly increases the solubility of TiO2 promoting the changes in morphology from nearly spherical titania nanoparticles to elongated titanate nanosheets. The single titanate phase was obtained after energetically the most intensive treatment, i.e. 18 hat 160 degrees C. The step-by-step optimization was thus necessary to finally distinguish the titanates from titania in terms of structural and spectral properties and to finally allow the clarification of long-standing confusion between titania and titanates. The obtained single titanate phase was furtherly used to fabricate a humidity sensor, which showed remarkably rapid response and quick recovery time.
PB  - Elsevier Science Sa, Lausanne
T2  - Journal of Alloys and Compounds
T1  - From titania to titanates: Phase and morphological transition in less alkaline medium under mild conditions
EP  - 819
SP  - 810
VL  - 781
DO  - 10.1016/j.jallcom.2018.12.039
ER  - 

@article{
author = "Simović, Bojana and Dapčević, Aleksandra and Zdravković, J. and Tasić, Nikola and Kovač, S. and Krstić, Jugoslav and Branković, Goran",
year = "2019",
abstract = "In this work, nine products were prepared by modifying the experimental conditions (6, 12 and 18 hat 110, 135 and 160 degrees C) of hydrothermal treatment of starting nanoanatase in significantly less concentrated alkaline medium than usual in order to obtain a pure titanate phase. The nanocrystalline samples were characterized by XRPD, FESEM, HRTEM/SAED, EDS, TG, FT-IR, UV-Vis and BET analyses. The results revealed that the structure, texture, morphology and band gap energy of samples strongly depend on conditions of hydrothermal treatment. The intensification of hydrothermal treatment significantly increases the solubility of TiO2 promoting the changes in morphology from nearly spherical titania nanoparticles to elongated titanate nanosheets. The single titanate phase was obtained after energetically the most intensive treatment, i.e. 18 hat 160 degrees C. The step-by-step optimization was thus necessary to finally distinguish the titanates from titania in terms of structural and spectral properties and to finally allow the clarification of long-standing confusion between titania and titanates. The obtained single titanate phase was furtherly used to fabricate a humidity sensor, which showed remarkably rapid response and quick recovery time.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Journal of Alloys and Compounds",
title = "From titania to titanates: Phase and morphological transition in less alkaline medium under mild conditions",
pages = "819-810",
volume = "781",
doi = "10.1016/j.jallcom.2018.12.039"
}

Simović, B., Dapčević, A., Zdravković, J., Tasić, N., Kovač, S., Krstić, J.,& Branković, G.. (2019). From titania to titanates: Phase and morphological transition in less alkaline medium under mild conditions. in Journal of Alloys and Compounds
Elsevier Science Sa, Lausanne., 781, 810-819.
https://doi.org/10.1016/j.jallcom.2018.12.039

Simović B, Dapčević A, Zdravković J, Tasić N, Kovač S, Krstić J, Branković G. From titania to titanates: Phase and morphological transition in less alkaline medium under mild conditions. in Journal of Alloys and Compounds. 2019;781:810-819.
doi:10.1016/j.jallcom.2018.12.039 .

Simović, Bojana, Dapčević, Aleksandra, Zdravković, J., Tasić, Nikola, Kovač, S., Krstić, Jugoslav, Branković, Goran, "From titania to titanates: Phase and morphological transition in less alkaline medium under mild conditions" in Journal of Alloys and Compounds, 781 (2019):810-819,
https://doi.org/10.1016/j.jallcom.2018.12.039 . .

TY  - CONF
AU  - Savić, Slavica
AU  - Vojisavljević, Katarina
AU  - Počuča Nešić, Milica
AU  - Knežević, Nikola
AU  - Đokić, Veljko
AU  - Ribić, Vesna
AU  - Branković, Goran
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6111
AB  - This work presents the fabrication of humidity sensor based on SnO2 sensing material derived by the nanocasting process using hydrothermally obtained KIT-5 as a hard template.
In a typical wet impregnation process, the infiltration of Sn precursor into mesoporous silica KIT-5, and later evaporation of the solvent were conducted to fill pores to 15 % of the template pore volume. The calcination and removal of the template were performed to obtain the desired mesoporous SnO2. The obtained powder (P) was mixed with a 10 % ethyl-cellulose in α- terpineol solution (S) and acetic acid (A) in the weight ratio P:S:A=7:69.7:23.3 to form a homogeneous paste which was further deposited by doctor blade technique onto alumina substrate with screen printed Pt/Ag electrodes. The film was subjected to a specific drying regime and finally calcined at 550 °C for 5 h.
The obtained SnO2 nanoparticles as well KIT-5 template were characterized using X-ray diffraction (XRD) spectroscopy, Brunauer–Emmett–Teller (BET) analysis and Transmission Electron Microscopy (TEM). Cross section and surface morphology of SnO2 film were characterized by Field Emission Scanning Electron Microscopy (FESEM). The humidity sensing properties of the mesoporous SnO2 sensor were investigated in a JEIO TECH TH-KE-025 temperature and humidity climatic chamber in the range 30–90 % RH. Complex impedance spectra of the as-fabricated sensor were analyzed at room temperature and 50 °C with a HIOKI 3532-50 LCR HiTESTER in a frequency range 42 Hz - 1 MHz.
Nitrogen adsorption isotherms of KIT-5 showed high specific surface area of 610 m2g-1 and average pore diameter of 5.2 nm while those values for SnO2 sample were 33 m2g-1 and 19.9 nm respectively. Even though that mesoporous ordering of nanocasted negative replica was observed by TEM, the presence of agglomerates in SnO2, as well as the relatively low specific surface area of 33 m2g-1, confirm its partial degradation. Diffraction patterns from TEM display well-defined rings typical for cassiterite SnO2. The impedance measured at 42 Hz, at room temperature, and in the range 40-90% RH reduced 509 times, while at 50 °C it reduced 48 times. The sensor exhibited quick response (5 s) and recovery time (16 s) when it exposed to humidity change from 37% RH to 90% RH, and relatively low hysteresis of 3.2% observed at 40% RH and at room temperature showing its promising capacity as a humidity sensor.
PB  - Societa ceramica italiana
PB  - Politecnico di Torino
C3  - Abstract Book / XVI Conference and Exhibition of the European Ceramic Society XVI ECerS Conference, Torino, 16-20 June 2019
T1  - Nanocasting Synthesis of Mesoporous SnO2 for Humidity Sensor Application
SP  - 764
UR  - https://hdl.handle.net/21.15107/rcub_technorep_6111
ER  - 

@conference{
author = "Savić, Slavica and Vojisavljević, Katarina and Počuča Nešić, Milica and Knežević, Nikola and Đokić, Veljko and Ribić, Vesna and Branković, Goran",
year = "2019",
abstract = "This work presents the fabrication of humidity sensor based on SnO2 sensing material derived by the nanocasting process using hydrothermally obtained KIT-5 as a hard template.
In a typical wet impregnation process, the infiltration of Sn precursor into mesoporous silica KIT-5, and later evaporation of the solvent were conducted to fill pores to 15 % of the template pore volume. The calcination and removal of the template were performed to obtain the desired mesoporous SnO2. The obtained powder (P) was mixed with a 10 % ethyl-cellulose in α- terpineol solution (S) and acetic acid (A) in the weight ratio P:S:A=7:69.7:23.3 to form a homogeneous paste which was further deposited by doctor blade technique onto alumina substrate with screen printed Pt/Ag electrodes. The film was subjected to a specific drying regime and finally calcined at 550 °C for 5 h.
The obtained SnO2 nanoparticles as well KIT-5 template were characterized using X-ray diffraction (XRD) spectroscopy, Brunauer–Emmett–Teller (BET) analysis and Transmission Electron Microscopy (TEM). Cross section and surface morphology of SnO2 film were characterized by Field Emission Scanning Electron Microscopy (FESEM). The humidity sensing properties of the mesoporous SnO2 sensor were investigated in a JEIO TECH TH-KE-025 temperature and humidity climatic chamber in the range 30–90 % RH. Complex impedance spectra of the as-fabricated sensor were analyzed at room temperature and 50 °C with a HIOKI 3532-50 LCR HiTESTER in a frequency range 42 Hz - 1 MHz.
Nitrogen adsorption isotherms of KIT-5 showed high specific surface area of 610 m2g-1 and average pore diameter of 5.2 nm while those values for SnO2 sample were 33 m2g-1 and 19.9 nm respectively. Even though that mesoporous ordering of nanocasted negative replica was observed by TEM, the presence of agglomerates in SnO2, as well as the relatively low specific surface area of 33 m2g-1, confirm its partial degradation. Diffraction patterns from TEM display well-defined rings typical for cassiterite SnO2. The impedance measured at 42 Hz, at room temperature, and in the range 40-90% RH reduced 509 times, while at 50 °C it reduced 48 times. The sensor exhibited quick response (5 s) and recovery time (16 s) when it exposed to humidity change from 37% RH to 90% RH, and relatively low hysteresis of 3.2% observed at 40% RH and at room temperature showing its promising capacity as a humidity sensor.",
publisher = "Societa ceramica italiana, Politecnico di Torino",
journal = "Abstract Book / XVI Conference and Exhibition of the European Ceramic Society XVI ECerS Conference, Torino, 16-20 June 2019",
title = "Nanocasting Synthesis of Mesoporous SnO2 for Humidity Sensor Application",
pages = "764",
url = "https://hdl.handle.net/21.15107/rcub_technorep_6111"
}

Savić, S., Vojisavljević, K., Počuča Nešić, M., Knežević, N., Đokić, V., Ribić, V.,& Branković, G.. (2019). Nanocasting Synthesis of Mesoporous SnO2 for Humidity Sensor Application. in Abstract Book / XVI Conference and Exhibition of the European Ceramic Society XVI ECerS Conference, Torino, 16-20 June 2019
Societa ceramica italiana., 764.
https://hdl.handle.net/21.15107/rcub_technorep_6111

Savić S, Vojisavljević K, Počuča Nešić M, Knežević N, Đokić V, Ribić V, Branković G. Nanocasting Synthesis of Mesoporous SnO2 for Humidity Sensor Application. in Abstract Book / XVI Conference and Exhibition of the European Ceramic Society XVI ECerS Conference, Torino, 16-20 June 2019. 2019;:764.
https://hdl.handle.net/21.15107/rcub_technorep_6111 .

Savić, Slavica, Vojisavljević, Katarina, Počuča Nešić, Milica, Knežević, Nikola, Đokić, Veljko, Ribić, Vesna, Branković, Goran, "Nanocasting Synthesis of Mesoporous SnO2 for Humidity Sensor Application" in Abstract Book / XVI Conference and Exhibition of the European Ceramic Society XVI ECerS Conference, Torino, 16-20 June 2019 (2019):764,
https://hdl.handle.net/21.15107/rcub_technorep_6111 .

TY  - JOUR
AU  - Radojković, Aleksandar
AU  - Luković-Golić, Danijela
AU  - Ćirković, Jovana
AU  - Marinković-Stanojević, Zorica
AU  - Pajić, Damir
AU  - Torić, Filip
AU  - Dapčević, Aleksandra
AU  - Vulić, Predrag
AU  - Branković, Zorica
AU  - Branković, Goran
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3856
AB  - Bulk ceramic samples of BiFeO3 were light doped (up to 1%) with Nb5+ in the place of Fe3+ (B-site doping) and their multiferroic properties were investigated using XRD, SEM, polarization (PMTS) and magnetization (SQUID) techniques. It is shown that even the small percentages of doping can notably change electric and magnetic behavior. Electric conductivity differs by two orders of magnitude between samples doped with 0.2% and 1% Nb. The ferroelectric behavior strongly depended on conduction mechanism, and transition from space-charge-limited current (SCLC) conduction to trap-filled limited (TFL) conduction regime reflected on a change in hysteresis patterns, particularly for the samples with 0.2% and 0.5% Nb. Separation of ZFC-FC magnetization curves occurred for all Nb concentrations and increased with Nb doping. Weak ferromagnetic behavior and the increase of remnant magnetization with Nb concentration was observed from the hysteresis measurements. Coercive field changed drastically compared to the pure BiFeO3, namely, the sample with 1% Nb exhibited very high coercive magnetic field of 10 kOe.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Tuning of BiFeO3 multiferroic properties by light doping with Nb
EP  - 16744
IS  - 14
SP  - 16739
VL  - 44
DO  - 10.1016/j.ceramint.2018.06.103
ER  - 

@article{
author = "Radojković, Aleksandar and Luković-Golić, Danijela and Ćirković, Jovana and Marinković-Stanojević, Zorica and Pajić, Damir and Torić, Filip and Dapčević, Aleksandra and Vulić, Predrag and Branković, Zorica and Branković, Goran",
year = "2018",
abstract = "Bulk ceramic samples of BiFeO3 were light doped (up to 1%) with Nb5+ in the place of Fe3+ (B-site doping) and their multiferroic properties were investigated using XRD, SEM, polarization (PMTS) and magnetization (SQUID) techniques. It is shown that even the small percentages of doping can notably change electric and magnetic behavior. Electric conductivity differs by two orders of magnitude between samples doped with 0.2% and 1% Nb. The ferroelectric behavior strongly depended on conduction mechanism, and transition from space-charge-limited current (SCLC) conduction to trap-filled limited (TFL) conduction regime reflected on a change in hysteresis patterns, particularly for the samples with 0.2% and 0.5% Nb. Separation of ZFC-FC magnetization curves occurred for all Nb concentrations and increased with Nb doping. Weak ferromagnetic behavior and the increase of remnant magnetization with Nb concentration was observed from the hysteresis measurements. Coercive field changed drastically compared to the pure BiFeO3, namely, the sample with 1% Nb exhibited very high coercive magnetic field of 10 kOe.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Tuning of BiFeO3 multiferroic properties by light doping with Nb",
pages = "16744-16739",
number = "14",
volume = "44",
doi = "10.1016/j.ceramint.2018.06.103"
}

Radojković, A., Luković-Golić, D., Ćirković, J., Marinković-Stanojević, Z., Pajić, D., Torić, F., Dapčević, A., Vulić, P., Branković, Z.,& Branković, G.. (2018). Tuning of BiFeO3 multiferroic properties by light doping with Nb. in Ceramics International
Elsevier Sci Ltd, Oxford., 44(14), 16739-16744.
https://doi.org/10.1016/j.ceramint.2018.06.103

Radojković A, Luković-Golić D, Ćirković J, Marinković-Stanojević Z, Pajić D, Torić F, Dapčević A, Vulić P, Branković Z, Branković G. Tuning of BiFeO3 multiferroic properties by light doping with Nb. in Ceramics International. 2018;44(14):16739-16744.
doi:10.1016/j.ceramint.2018.06.103 .

Radojković, Aleksandar, Luković-Golić, Danijela, Ćirković, Jovana, Marinković-Stanojević, Zorica, Pajić, Damir, Torić, Filip, Dapčević, Aleksandra, Vulić, Predrag, Branković, Zorica, Branković, Goran, "Tuning of BiFeO3 multiferroic properties by light doping with Nb" in Ceramics International, 44, no. 14 (2018):16739-16744,
https://doi.org/10.1016/j.ceramint.2018.06.103 . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Živković, Predrag M.
AU  - Lović, Jelena
AU  - Branković, Goran
PY  - 2017
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5815
AB  - In this study, mechanism of electrodeposition of zinc from the alkaline electrolytes has been investigated using the general theory of disperse deposits formation. The exchange current densities in the range 18.4-88 mA cm(-2) were determined using new method based on comparison of experimental and simulated polarization curves, and the excellent agreement with the values found in the literature has been attained. Correlation between the polarization characteristics and morphologies of zinc deposits characterized by the scanning electron microscopic (SEM) technique was established. The spongy-like particles constructed from nanofilaments and the large grains or boulders were formed in the zone of the fast increase of the current density with the overpotential before the plateau of the limiting diffusion current density was reached. The shape of dendrites, formed inside the plateau of the limiting diffusion current density and at the higher ones, strongly depended on overpotential of the electrodeposition. Mechanism of formation of all obtained forms was discussed by the consideration of the different rates of growth of surface protrusions in a function of the overpotential of electrodeposition through the analysis of the change of the ratio between the height and the radius of the protrusions. In order to confirm of the proposed mechanism, comparison with polarization and morphological characteristics of the other metals characterized by the different exchange current density values was made and discussed. Although zinc is classified in the group of the normal metals characterized by the high values of the exchange current density, it was found that the polarization and morphological characteristics of zinc show certain and strong similarities with those of copper, classifying zinc just at boundary between the normal and intermediate metals, that is confirmed by the estimation of the exchange current density value for zinc.
PB  - Elsevier
T2  - Journal of Electroanalytical Chemistry
T1  - Application of the general theory of disperse deposits formation in an investigation of mechanism of zinc electrodeposition from the alkaline electrolytes
EP  - 74
SP  - 65
VL  - 785
DO  - 10.1016/j.jelechem.2016.12.024
ER  - 

@article{
author = "Nikolić, Nebojša D. and Živković, Predrag M. and Lović, Jelena and Branković, Goran",
year = "2017",
abstract = "In this study, mechanism of electrodeposition of zinc from the alkaline electrolytes has been investigated using the general theory of disperse deposits formation. The exchange current densities in the range 18.4-88 mA cm(-2) were determined using new method based on comparison of experimental and simulated polarization curves, and the excellent agreement with the values found in the literature has been attained. Correlation between the polarization characteristics and morphologies of zinc deposits characterized by the scanning electron microscopic (SEM) technique was established. The spongy-like particles constructed from nanofilaments and the large grains or boulders were formed in the zone of the fast increase of the current density with the overpotential before the plateau of the limiting diffusion current density was reached. The shape of dendrites, formed inside the plateau of the limiting diffusion current density and at the higher ones, strongly depended on overpotential of the electrodeposition. Mechanism of formation of all obtained forms was discussed by the consideration of the different rates of growth of surface protrusions in a function of the overpotential of electrodeposition through the analysis of the change of the ratio between the height and the radius of the protrusions. In order to confirm of the proposed mechanism, comparison with polarization and morphological characteristics of the other metals characterized by the different exchange current density values was made and discussed. Although zinc is classified in the group of the normal metals characterized by the high values of the exchange current density, it was found that the polarization and morphological characteristics of zinc show certain and strong similarities with those of copper, classifying zinc just at boundary between the normal and intermediate metals, that is confirmed by the estimation of the exchange current density value for zinc.",
publisher = "Elsevier",
journal = "Journal of Electroanalytical Chemistry",
title = "Application of the general theory of disperse deposits formation in an investigation of mechanism of zinc electrodeposition from the alkaline electrolytes",
pages = "74-65",
volume = "785",
doi = "10.1016/j.jelechem.2016.12.024"
}

Nikolić, N. D., Živković, P. M., Lović, J.,& Branković, G.. (2017). Application of the general theory of disperse deposits formation in an investigation of mechanism of zinc electrodeposition from the alkaline electrolytes. in Journal of Electroanalytical Chemistry
Elsevier., 785, 65-74.
https://doi.org/10.1016/j.jelechem.2016.12.024

Nikolić ND, Živković PM, Lović J, Branković G. Application of the general theory of disperse deposits formation in an investigation of mechanism of zinc electrodeposition from the alkaline electrolytes. in Journal of Electroanalytical Chemistry. 2017;785:65-74.
doi:10.1016/j.jelechem.2016.12.024 .

Nikolić, Nebojša D., Živković, Predrag M., Lović, Jelena, Branković, Goran, "Application of the general theory of disperse deposits formation in an investigation of mechanism of zinc electrodeposition from the alkaline electrolytes" in Journal of Electroanalytical Chemistry, 785 (2017):65-74,
https://doi.org/10.1016/j.jelechem.2016.12.024 . .

TY  - JOUR
AU  - Savić, Slavica M.
AU  - Stojanović, G.
AU  - Vasiljević, D.
AU  - Vojisavljević, K.
AU  - Dapčević, Aleksandra
AU  - Radojković, Aleksandar
AU  - Prsić, S.
AU  - Branković, Goran
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3286
AB  - The chemical synthesis of nickel manganite powder was performed by a complex polymerization method (CPM). The obtained fine nanoscaled powders were uniaxially pressed and sintered at different temperatures: 1000-1200 degrees C for 2 h, and different atmospheres: air and oxygen. The highest density was obtained for the sample sintered at 1200 degrees C in oxygen atmosphere. The energy for direct band gap transition (Eg) calculated from the Tauc plot decreases from 1.51 to 1.40 eV with the increase of the sintering temperature. Indentation experiments were carried out using a three-sided pyramidal (Berkovich) diamond tip, and Young's modulus of elasticity and hardness of NTC (negative temperature coefficient) ceramics at various indentation depths were calculated. The highest hardness (0.754 GPa) and elastic modulus (16.888 GPa) are exhibited by the ceramics sintered at highest temperature in oxygen atmosphere.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method
EP  - 12282
IS  - 10
SP  - 12276
VL  - 42
DO  - 10.1016/j.ceramint.2016.04.174
ER  - 

@article{
author = "Savić, Slavica M. and Stojanović, G. and Vasiljević, D. and Vojisavljević, K. and Dapčević, Aleksandra and Radojković, Aleksandar and Prsić, S. and Branković, Goran",
year = "2016",
abstract = "The chemical synthesis of nickel manganite powder was performed by a complex polymerization method (CPM). The obtained fine nanoscaled powders were uniaxially pressed and sintered at different temperatures: 1000-1200 degrees C for 2 h, and different atmospheres: air and oxygen. The highest density was obtained for the sample sintered at 1200 degrees C in oxygen atmosphere. The energy for direct band gap transition (Eg) calculated from the Tauc plot decreases from 1.51 to 1.40 eV with the increase of the sintering temperature. Indentation experiments were carried out using a three-sided pyramidal (Berkovich) diamond tip, and Young's modulus of elasticity and hardness of NTC (negative temperature coefficient) ceramics at various indentation depths were calculated. The highest hardness (0.754 GPa) and elastic modulus (16.888 GPa) are exhibited by the ceramics sintered at highest temperature in oxygen atmosphere.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method",
pages = "12282-12276",
number = "10",
volume = "42",
doi = "10.1016/j.ceramint.2016.04.174"
}

Savić, S. M., Stojanović, G., Vasiljević, D., Vojisavljević, K., Dapčević, A., Radojković, A., Prsić, S.,& Branković, G.. (2016). Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method. in Ceramics International
Elsevier Sci Ltd, Oxford., 42(10), 12276-12282.
https://doi.org/10.1016/j.ceramint.2016.04.174

Savić SM, Stojanović G, Vasiljević D, Vojisavljević K, Dapčević A, Radojković A, Prsić S, Branković G. Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method. in Ceramics International. 2016;42(10):12276-12282.
doi:10.1016/j.ceramint.2016.04.174 .

Savić, Slavica M., Stojanović, G., Vasiljević, D., Vojisavljević, K., Dapčević, Aleksandra, Radojković, Aleksandar, Prsić, S., Branković, Goran, "Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method" in Ceramics International, 42, no. 10 (2016):12276-12282,
https://doi.org/10.1016/j.ceramint.2016.04.174 . .

TY  - JOUR
AU  - Luković-Golić, Danijela
AU  - Radojković, Aleksandar
AU  - Ćirković, Jovana
AU  - Dapčević, Aleksandra
AU  - Pajić, Damir
AU  - Tasić, Nikola
AU  - Savić, Slavica M.
AU  - Počuča Nešić, Milica
AU  - Marković, Smilja
AU  - Branković, Goran
AU  - Marinković-Stanojević, Zorica
AU  - Branković, Zorica
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3473
AB  - BiFeO3 powders were synthesized by sonochemically assisted hydrothermal and hydro-evaporation methods. The X-ray diffraction confirmed the presence of secondary phases, Bi25FeO39 and Bi2Fe4O9, in as prepared BiFeO3 powders. Optimization of sintering conditions indicated that temperature of 800 degrees C and time of 2 h after pressing at 9 t/cm(2) provided ceramics samples with"the highest density (up to 96% of theoretical density) and the lowest content of secondary phases. Ferroelectric and magnetic characterization was performed on two selected ceramics samples with the highest densities. Ceramics obtained from the powder synthesized by the hydrothermal method showed greater lattice distortion along [1 1 1] axis and smaller grains, which resulted in larger values of electric polarization at room temperature. It also exhibited less Fe(3d)-O(2p) orbital overlapping due to a larger Fe-O-Fe bond angle, causing lower antiferromagnetic ordering and weak ferromagnetic behavior at low temperatures.
PB  - Elsevier Sci Ltd, Oxford
T2  - Journal of the European Ceramic Society
T1  - Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods
EP  - 1631
IS  - 7
SP  - 1623
VL  - 36
DO  - 10.1016/j.jeurceramsoc.2016.01.031
ER  - 

@article{
author = "Luković-Golić, Danijela and Radojković, Aleksandar and Ćirković, Jovana and Dapčević, Aleksandra and Pajić, Damir and Tasić, Nikola and Savić, Slavica M. and Počuča Nešić, Milica and Marković, Smilja and Branković, Goran and Marinković-Stanojević, Zorica and Branković, Zorica",
year = "2016",
abstract = "BiFeO3 powders were synthesized by sonochemically assisted hydrothermal and hydro-evaporation methods. The X-ray diffraction confirmed the presence of secondary phases, Bi25FeO39 and Bi2Fe4O9, in as prepared BiFeO3 powders. Optimization of sintering conditions indicated that temperature of 800 degrees C and time of 2 h after pressing at 9 t/cm(2) provided ceramics samples with"the highest density (up to 96% of theoretical density) and the lowest content of secondary phases. Ferroelectric and magnetic characterization was performed on two selected ceramics samples with the highest densities. Ceramics obtained from the powder synthesized by the hydrothermal method showed greater lattice distortion along [1 1 1] axis and smaller grains, which resulted in larger values of electric polarization at room temperature. It also exhibited less Fe(3d)-O(2p) orbital overlapping due to a larger Fe-O-Fe bond angle, causing lower antiferromagnetic ordering and weak ferromagnetic behavior at low temperatures.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Journal of the European Ceramic Society",
title = "Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods",
pages = "1631-1623",
number = "7",
volume = "36",
doi = "10.1016/j.jeurceramsoc.2016.01.031"
}

Luković-Golić, D., Radojković, A., Ćirković, J., Dapčević, A., Pajić, D., Tasić, N., Savić, S. M., Počuča Nešić, M., Marković, S., Branković, G., Marinković-Stanojević, Z.,& Branković, Z.. (2016). Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods. in Journal of the European Ceramic Society
Elsevier Sci Ltd, Oxford., 36(7), 1623-1631.
https://doi.org/10.1016/j.jeurceramsoc.2016.01.031

Luković-Golić D, Radojković A, Ćirković J, Dapčević A, Pajić D, Tasić N, Savić SM, Počuča Nešić M, Marković S, Branković G, Marinković-Stanojević Z, Branković Z. Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods. in Journal of the European Ceramic Society. 2016;36(7):1623-1631.
doi:10.1016/j.jeurceramsoc.2016.01.031 .

Luković-Golić, Danijela, Radojković, Aleksandar, Ćirković, Jovana, Dapčević, Aleksandra, Pajić, Damir, Tasić, Nikola, Savić, Slavica M., Počuča Nešić, Milica, Marković, Smilja, Branković, Goran, Marinković-Stanojević, Zorica, Branković, Zorica, "Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods" in Journal of the European Ceramic Society, 36, no. 7 (2016):1623-1631,
https://doi.org/10.1016/j.jeurceramsoc.2016.01.031 . .

TY  - JOUR
AU  - Dapčević, Aleksandra
AU  - Poleti, Dejan
AU  - Rogan, Jelena
AU  - Radojković, Aleksandar
AU  - Radović, M.
AU  - Branković, Goran
PY  - 2015
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3135
AB  - The possibility to stabilize the delta-Bi2O3-type polymorph with high ionic conductivity by doping with Tm2O3 was investigated in this study. Five microaystalline samples were synthesized at 750 degrees C from alpha-Bi2O3 and Tm2O3 mixtures with compositions (Bi1-xTmx)(2)O-3, where x = 0.04, 0.08, 0.11, 0.14 and 0.20. The XRD, SEM, HRTEM and SAED results showed that the targeted delta-Bi2O3-type single-phase (space group Fm (3) over barm) was formed for 0.11  lt = x  lt = 0.20. The unit cell parameter of delta-Bi2O3-type phase decreases with increase in Tm content. According to DTA, no phase transitions were observed in the sample with x = 020, indicating that the obtained delta-Bi2O3-type phase is structurally stable from room temperature to 985 degrees C. Based on EIS, (Bi0.80Tm0.20)(2)O-3 exhibits high conductivity (0.117 S cm(-1) at 550 degrees C) with activation energies: 0.38(4) eV above 550 degrees C and 127(2) eV below 550 degrees C, due to the change in charge carrier mobility. The effect of thermal aging was investigated and discussed.
PB  - Elsevier Science Bv, Amsterdam
T2  - Solid State Ionics
T1  - A new electrolyte based on Tm3+-doped delta-Bi2O3-type phase with enhanced conductivity
EP  - 23
SP  - 18
VL  - 280
DO  - 10.1016/j.ssi.2015.08.004
ER  - 

@article{
author = "Dapčević, Aleksandra and Poleti, Dejan and Rogan, Jelena and Radojković, Aleksandar and Radović, M. and Branković, Goran",
year = "2015",
abstract = "The possibility to stabilize the delta-Bi2O3-type polymorph with high ionic conductivity by doping with Tm2O3 was investigated in this study. Five microaystalline samples were synthesized at 750 degrees C from alpha-Bi2O3 and Tm2O3 mixtures with compositions (Bi1-xTmx)(2)O-3, where x = 0.04, 0.08, 0.11, 0.14 and 0.20. The XRD, SEM, HRTEM and SAED results showed that the targeted delta-Bi2O3-type single-phase (space group Fm (3) over barm) was formed for 0.11  lt = x  lt = 0.20. The unit cell parameter of delta-Bi2O3-type phase decreases with increase in Tm content. According to DTA, no phase transitions were observed in the sample with x = 020, indicating that the obtained delta-Bi2O3-type phase is structurally stable from room temperature to 985 degrees C. Based on EIS, (Bi0.80Tm0.20)(2)O-3 exhibits high conductivity (0.117 S cm(-1) at 550 degrees C) with activation energies: 0.38(4) eV above 550 degrees C and 127(2) eV below 550 degrees C, due to the change in charge carrier mobility. The effect of thermal aging was investigated and discussed.",
publisher = "Elsevier Science Bv, Amsterdam",
journal = "Solid State Ionics",
title = "A new electrolyte based on Tm3+-doped delta-Bi2O3-type phase with enhanced conductivity",
pages = "23-18",
volume = "280",
doi = "10.1016/j.ssi.2015.08.004"
}

Dapčević, A., Poleti, D., Rogan, J., Radojković, A., Radović, M.,& Branković, G.. (2015). A new electrolyte based on Tm3+-doped delta-Bi2O3-type phase with enhanced conductivity. in Solid State Ionics
Elsevier Science Bv, Amsterdam., 280, 18-23.
https://doi.org/10.1016/j.ssi.2015.08.004

Dapčević A, Poleti D, Rogan J, Radojković A, Radović M, Branković G. A new electrolyte based on Tm3+-doped delta-Bi2O3-type phase with enhanced conductivity. in Solid State Ionics. 2015;280:18-23.
doi:10.1016/j.ssi.2015.08.004 .

Dapčević, Aleksandra, Poleti, Dejan, Rogan, Jelena, Radojković, Aleksandar, Radović, M., Branković, Goran, "A new electrolyte based on Tm3+-doped delta-Bi2O3-type phase with enhanced conductivity" in Solid State Ionics, 280 (2015):18-23,
https://doi.org/10.1016/j.ssi.2015.08.004 . .

TY  - JOUR
AU  - Prsić, S.
AU  - Savić, Slavica M.
AU  - Branković, Zorica
AU  - Vrtnik, S.
AU  - Dapčević, Aleksandra
AU  - Branković, Goran
PY  - 2015
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2992
AB  - In the last decade, the sodium cobaltite ceramic became a promising candidate for potential thermoelectric applications, because of its large thermopower and low resistivity. In this work, polycrystalline samples of NaCo(2-x)CuxO(4) (x = 0, 0.01, 0.03, 0.05) were prepared using mechanochemically assisted solid-state reaction method (MASSR) and the citric acid complex method (CAC). Bulk samples were prepared by pressing into disc-shaped pellets and subsequently subjected to a thermal treatment at 880 degrees C in inert argon atmosphere. Changes in structural and microstructural characteristics of the samples, caused by the substitution of Cu for Co, were characterized using X-ray diffraction (XRD) analysis, and scanning electron microscopy (SEM), respectively. The results of inductively coupled plasma (ICP) analysis showed that the compositions of the final products correspond to gamma-NaCo2O4 and confirmed that desired compound was obtained in both syntheses procedures. The advantages and disadvantages of these two syntheses procedures have been observed and discussed: the CAC method enabled obtaining samples with higher density and fine microstructure compared to the MASSR method, thus better thermoelectric properties. The Cu2+ substitution led to the increase in Seebeck coefficient in both synthesis routes. The highest figure of merit of 0.022 at 300 K was observed for the sample doped with 1 mol% Cu, obtained by the CAC method, and it was almost twice higher than in the undoped sample confirming the significant influence of Cu-doping with even small concentrations.
PB  - Elsevier Science Sa, Lausanne
T2  - Journal of Alloys and Compounds
T1  - Mechanochemically assisted solid-state and citric acid complex syntheses of Cu-doped sodium cobaltite ceramicsh
EP  - 487
SP  - 480
VL  - 640
DO  - 10.1016/j.jallcom.2015.04.003
ER  - 

@article{
author = "Prsić, S. and Savić, Slavica M. and Branković, Zorica and Vrtnik, S. and Dapčević, Aleksandra and Branković, Goran",
year = "2015",
abstract = "In the last decade, the sodium cobaltite ceramic became a promising candidate for potential thermoelectric applications, because of its large thermopower and low resistivity. In this work, polycrystalline samples of NaCo(2-x)CuxO(4) (x = 0, 0.01, 0.03, 0.05) were prepared using mechanochemically assisted solid-state reaction method (MASSR) and the citric acid complex method (CAC). Bulk samples were prepared by pressing into disc-shaped pellets and subsequently subjected to a thermal treatment at 880 degrees C in inert argon atmosphere. Changes in structural and microstructural characteristics of the samples, caused by the substitution of Cu for Co, were characterized using X-ray diffraction (XRD) analysis, and scanning electron microscopy (SEM), respectively. The results of inductively coupled plasma (ICP) analysis showed that the compositions of the final products correspond to gamma-NaCo2O4 and confirmed that desired compound was obtained in both syntheses procedures. The advantages and disadvantages of these two syntheses procedures have been observed and discussed: the CAC method enabled obtaining samples with higher density and fine microstructure compared to the MASSR method, thus better thermoelectric properties. The Cu2+ substitution led to the increase in Seebeck coefficient in both synthesis routes. The highest figure of merit of 0.022 at 300 K was observed for the sample doped with 1 mol% Cu, obtained by the CAC method, and it was almost twice higher than in the undoped sample confirming the significant influence of Cu-doping with even small concentrations.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Journal of Alloys and Compounds",
title = "Mechanochemically assisted solid-state and citric acid complex syntheses of Cu-doped sodium cobaltite ceramicsh",
pages = "487-480",
volume = "640",
doi = "10.1016/j.jallcom.2015.04.003"
}

Prsić, S., Savić, S. M., Branković, Z., Vrtnik, S., Dapčević, A.,& Branković, G.. (2015). Mechanochemically assisted solid-state and citric acid complex syntheses of Cu-doped sodium cobaltite ceramicsh. in Journal of Alloys and Compounds
Elsevier Science Sa, Lausanne., 640, 480-487.
https://doi.org/10.1016/j.jallcom.2015.04.003

Prsić S, Savić SM, Branković Z, Vrtnik S, Dapčević A, Branković G. Mechanochemically assisted solid-state and citric acid complex syntheses of Cu-doped sodium cobaltite ceramicsh. in Journal of Alloys and Compounds. 2015;640:480-487.
doi:10.1016/j.jallcom.2015.04.003 .

Prsić, S., Savić, Slavica M., Branković, Zorica, Vrtnik, S., Dapčević, Aleksandra, Branković, Goran, "Mechanochemically assisted solid-state and citric acid complex syntheses of Cu-doped sodium cobaltite ceramicsh" in Journal of Alloys and Compounds, 640 (2015):480-487,
https://doi.org/10.1016/j.jallcom.2015.04.003 . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Popov, Konstantin I.
AU  - Ivanović, Evica
AU  - Branković, Goran
AU  - Stevanović, Sanja
AU  - Živković, Predrag M.
PY  - 2015
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5806
AB  - Electrodeposition of lead from the concentrated nitrate electrolyte in the potentiostatic regime of electrolysis has been investigated by the analysis of the potentiostatic current transients and scanning electron microscope (SEM). It was found that the process of Pb nucleation from the concentrated electrolyte follows Scharifker model based on the 3D (three-dimensional) instantaneous nucleation with diffusion-controlled growth. The deviations of the obtained dependencies from the theoretical prediction for this model have been also discussed. Needle-like and fern-like dendrites, as well as crystals of irregular shape (precursors of dendrites) were formed in the diffusion controlled electrodeposition. The SEM analysis of these dendritic forms revealed their 2D (two-dimensional) growth. The size of needle-like dendrites was considerably larger than the size of both the fern-like dendrites and the irregular crystals. Although the electrodeposition process occurred inside the linear diffusion layer of the macroelectrode, the shape and size of dendrites were determined by the effect of local diffusion fields formed around tips (spherical diffusion) and top edges (cylindrical diffusion) of protrusions formed in the initial stage of the electrodeposition. The growth rates under the conditions of spherical and cylindrical diffusion control were mutually compared and a faster growth under the conditions of the spherical, in relation to the cylindrical diffusion, was proved. The effect of the current density distribution on formation of the final forms of Pb dendrites was also discussed.
PB  - Elsevier
T2  - Journal of Electroanalytical Chemistry
T1  - The potentiostatic current transients and the role of local diffusion fields in formation of the 2D lead dendrites from the concentrated electrolyte
EP  - 148
SP  - 137
VL  - 739
DO  - 10.1016/j.jelechem.2014.12.020
ER  - 

@article{
author = "Nikolić, Nebojša D. and Popov, Konstantin I. and Ivanović, Evica and Branković, Goran and Stevanović, Sanja and Živković, Predrag M.",
year = "2015",
abstract = "Electrodeposition of lead from the concentrated nitrate electrolyte in the potentiostatic regime of electrolysis has been investigated by the analysis of the potentiostatic current transients and scanning electron microscope (SEM). It was found that the process of Pb nucleation from the concentrated electrolyte follows Scharifker model based on the 3D (three-dimensional) instantaneous nucleation with diffusion-controlled growth. The deviations of the obtained dependencies from the theoretical prediction for this model have been also discussed. Needle-like and fern-like dendrites, as well as crystals of irregular shape (precursors of dendrites) were formed in the diffusion controlled electrodeposition. The SEM analysis of these dendritic forms revealed their 2D (two-dimensional) growth. The size of needle-like dendrites was considerably larger than the size of both the fern-like dendrites and the irregular crystals. Although the electrodeposition process occurred inside the linear diffusion layer of the macroelectrode, the shape and size of dendrites were determined by the effect of local diffusion fields formed around tips (spherical diffusion) and top edges (cylindrical diffusion) of protrusions formed in the initial stage of the electrodeposition. The growth rates under the conditions of spherical and cylindrical diffusion control were mutually compared and a faster growth under the conditions of the spherical, in relation to the cylindrical diffusion, was proved. The effect of the current density distribution on formation of the final forms of Pb dendrites was also discussed.",
publisher = "Elsevier",
journal = "Journal of Electroanalytical Chemistry",
title = "The potentiostatic current transients and the role of local diffusion fields in formation of the 2D lead dendrites from the concentrated electrolyte",
pages = "148-137",
volume = "739",
doi = "10.1016/j.jelechem.2014.12.020"
}

Nikolić, N. D., Popov, K. I., Ivanović, E., Branković, G., Stevanović, S.,& Živković, P. M.. (2015). The potentiostatic current transients and the role of local diffusion fields in formation of the 2D lead dendrites from the concentrated electrolyte. in Journal of Electroanalytical Chemistry
Elsevier., 739, 137-148.
https://doi.org/10.1016/j.jelechem.2014.12.020

Nikolić ND, Popov KI, Ivanović E, Branković G, Stevanović S, Živković PM. The potentiostatic current transients and the role of local diffusion fields in formation of the 2D lead dendrites from the concentrated electrolyte. in Journal of Electroanalytical Chemistry. 2015;739:137-148.
doi:10.1016/j.jelechem.2014.12.020 .

Nikolić, Nebojša D., Popov, Konstantin I., Ivanović, Evica, Branković, Goran, Stevanović, Sanja, Živković, Predrag M., "The potentiostatic current transients and the role of local diffusion fields in formation of the 2D lead dendrites from the concentrated electrolyte" in Journal of Electroanalytical Chemistry, 739 (2015):137-148,
https://doi.org/10.1016/j.jelechem.2014.12.020 . .

TY  - JOUR
AU  - Zdravković, Jelena
AU  - Simović, Bojana
AU  - Golubović, Aleksandar
AU  - Poleti, Dejan
AU  - Veljković, Ivana
AU  - Šćepanović, Maja
AU  - Branković, Goran
PY  - 2015
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5754
AB  - The effects of common precursors used in the synthesis of CeO2 nanopowders were investigated, and the structural and spectral properties of the resulting products were compared. Two cerium (III) salts, i.e., Ce(NO3)(3)center dot 6H(2)O and CeCl3 center dot 7H(2)O, and two cerium (IV) salts, i.e., Ce (SO4)(2)center dot 4H(2)O and (NH4)(2)Ce(NO3)(6) were applied. The proposed procedures for the CeO2 preparations were realizdd using the same hydrothermal treatment conditions. The products were characterized using X-ray powder diffraction (XRD) and thermogravimetric (TG) analysis, and the morphology was determined using scanning (SEM) and transmission electron microscopy (TEM). The spectral properties of the obtained nanopowders were characterized by FT-IR, Raman scattering and UV-vis spectroscopy. The results revealed the influence of the precursors on the crystallinity, crystallite size, band gap energy, morphology and purity of the synthesized samples.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Comparative study of CeO2 nanopowders obtained by the hydrothermal method from various precursors
EP  - 1979
IS  - 2
SP  - 1970
VL  - 41
DO  - 10.1016/j.ceramint.2014.08.122
ER  - 

@article{
author = "Zdravković, Jelena and Simović, Bojana and Golubović, Aleksandar and Poleti, Dejan and Veljković, Ivana and Šćepanović, Maja and Branković, Goran",
year = "2015",
abstract = "The effects of common precursors used in the synthesis of CeO2 nanopowders were investigated, and the structural and spectral properties of the resulting products were compared. Two cerium (III) salts, i.e., Ce(NO3)(3)center dot 6H(2)O and CeCl3 center dot 7H(2)O, and two cerium (IV) salts, i.e., Ce (SO4)(2)center dot 4H(2)O and (NH4)(2)Ce(NO3)(6) were applied. The proposed procedures for the CeO2 preparations were realizdd using the same hydrothermal treatment conditions. The products were characterized using X-ray powder diffraction (XRD) and thermogravimetric (TG) analysis, and the morphology was determined using scanning (SEM) and transmission electron microscopy (TEM). The spectral properties of the obtained nanopowders were characterized by FT-IR, Raman scattering and UV-vis spectroscopy. The results revealed the influence of the precursors on the crystallinity, crystallite size, band gap energy, morphology and purity of the synthesized samples.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Comparative study of CeO2 nanopowders obtained by the hydrothermal method from various precursors",
pages = "1979-1970",
number = "2",
volume = "41",
doi = "10.1016/j.ceramint.2014.08.122"
}

Zdravković, J., Simović, B., Golubović, A., Poleti, D., Veljković, I., Šćepanović, M.,& Branković, G.. (2015). Comparative study of CeO2 nanopowders obtained by the hydrothermal method from various precursors. in Ceramics International
Elsevier Sci Ltd, Oxford., 41(2), 1970-1979.
https://doi.org/10.1016/j.ceramint.2014.08.122

Zdravković J, Simović B, Golubović A, Poleti D, Veljković I, Šćepanović M, Branković G. Comparative study of CeO2 nanopowders obtained by the hydrothermal method from various precursors. in Ceramics International. 2015;41(2):1970-1979.
doi:10.1016/j.ceramint.2014.08.122 .

Zdravković, Jelena, Simović, Bojana, Golubović, Aleksandar, Poleti, Dejan, Veljković, Ivana, Šćepanović, Maja, Branković, Goran, "Comparative study of CeO2 nanopowders obtained by the hydrothermal method from various precursors" in Ceramics International, 41, no. 2 (2015):1970-1979,
https://doi.org/10.1016/j.ceramint.2014.08.122 . .

TY  - JOUR
AU  - Vuković, Marina
AU  - Branković, Goran
AU  - Marinković-Stanojević, Zorica
AU  - Poleti, Dejan
AU  - Branković, Zorica
PY  - 2015
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5808
AB  - Previously synthesized nanocrystalline ZnO doped with cobalt and manganese, Bi2O3 and Sb2O3 were the precursors for high voltage varistors preparation. Varistor ceramics were sintered at 750 degrees C, 770 degrees C or 900 degrees C for 1 h. An amount of 30 mass% of secondary phases and sintering temperature of 770 degrees C were found to be optimal for obtaining varistor with prominent properties. Achieved density was 97% of the theoretical value. Post-sintering phase composition included ZnO, gamma-Bi2O3 and pyrochlore-type with Zn2Bi3Sb3O14 nominal formula. Fine grained microstructure was accompanied with good phase distribution and excellent electrical characteristics: extraordinary high breakdown field of 3200 V mm(-1), high nonlinearity coefficients of 71 and 51 in 0.1-1 and 1-10 mA cm(-2) current density ranges, respectively, and low leakage current of 7.7 mu A cm(-2).
PB  - Elsevier Sci Ltd, Oxford
T2  - Journal of the European Ceramic Society
T1  - Ultra-high breakdown field varistors prepared from individually synthesized nanoprecursors
EP  - 1814
IS  - 6
SP  - 1807
VL  - 35
DO  - 10.1016/j.jeurceramsoc.2014.12.015
ER  - 

@article{
author = "Vuković, Marina and Branković, Goran and Marinković-Stanojević, Zorica and Poleti, Dejan and Branković, Zorica",
year = "2015",
abstract = "Previously synthesized nanocrystalline ZnO doped with cobalt and manganese, Bi2O3 and Sb2O3 were the precursors for high voltage varistors preparation. Varistor ceramics were sintered at 750 degrees C, 770 degrees C or 900 degrees C for 1 h. An amount of 30 mass% of secondary phases and sintering temperature of 770 degrees C were found to be optimal for obtaining varistor with prominent properties. Achieved density was 97% of the theoretical value. Post-sintering phase composition included ZnO, gamma-Bi2O3 and pyrochlore-type with Zn2Bi3Sb3O14 nominal formula. Fine grained microstructure was accompanied with good phase distribution and excellent electrical characteristics: extraordinary high breakdown field of 3200 V mm(-1), high nonlinearity coefficients of 71 and 51 in 0.1-1 and 1-10 mA cm(-2) current density ranges, respectively, and low leakage current of 7.7 mu A cm(-2).",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Journal of the European Ceramic Society",
title = "Ultra-high breakdown field varistors prepared from individually synthesized nanoprecursors",
pages = "1814-1807",
number = "6",
volume = "35",
doi = "10.1016/j.jeurceramsoc.2014.12.015"
}

Vuković, M., Branković, G., Marinković-Stanojević, Z., Poleti, D.,& Branković, Z.. (2015). Ultra-high breakdown field varistors prepared from individually synthesized nanoprecursors. in Journal of the European Ceramic Society
Elsevier Sci Ltd, Oxford., 35(6), 1807-1814.
https://doi.org/10.1016/j.jeurceramsoc.2014.12.015

Vuković M, Branković G, Marinković-Stanojević Z, Poleti D, Branković Z. Ultra-high breakdown field varistors prepared from individually synthesized nanoprecursors. in Journal of the European Ceramic Society. 2015;35(6):1807-1814.
doi:10.1016/j.jeurceramsoc.2014.12.015 .

Vuković, Marina, Branković, Goran, Marinković-Stanojević, Zorica, Poleti, Dejan, Branković, Zorica, "Ultra-high breakdown field varistors prepared from individually synthesized nanoprecursors" in Journal of the European Ceramic Society, 35, no. 6 (2015):1807-1814,
https://doi.org/10.1016/j.jeurceramsoc.2014.12.015 . .

TY  - JOUR
AU  - Tasić, Nikola
AU  - Rogan, Jelena
AU  - Poleti, Dejan
AU  - Radovanović, Lidija
AU  - Branković, Goran
PY  - 2014
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2668
AB  - Four novel polymeric iron(III) complexes with 2,2'-bipyridine (bipy) and different aromatic polycarboxylato ligands as anions of phthalic (pht), isophthalic (ipht), terephthalic (tpht) and pyromellitic (pyr) acid were synthesized by ligand exchange reaction. The complexes were characterized by elemental and TG/DSC analysis, FTIR and diffuse reflectance UV-Vis-NIR spectroscopy and magnetic susceptibility measurements. Based on the analytical and spectral data, the formulae of the complexes were {[Fe-4(bipy)(2) (H2O)(2)(OH)(6)(pht)(3)]center dot 2H(2)O}(n) (1), {[Fe-4(bipy)(2)(Hipht)(2)(ipht)(2)(OH)(6)]center dot 4H(2)O}(n) (2), {[Fe-4(bipy)(2)(Htpht)(2)(OH)(6)(tpht)(2)]center dot 4H(2)O}(n) (3) and {[Fe-4(bipy)(H2O)(8)-(OH)(4)(pyr)(2)]center dot H2O}(n) (4). All complexes were red brown and low-spin with a distorted octahedral geometry with FeO6 or FeN2O4 chromophores. The polycarboxylato ligands played a bridging role in all cases, whereas monodentate COO groups were present in 2 and 3, while bridging and chelate COO groups were established in 1 and 4. The thermal behaviours of 1-4 were investigated in detail and the molar dehydration enthalpies were calculated. According to the all those results, the structural formulae of complexes 1-4 were proposed.
AB  - Реакцијом измене лиганада синтетисана су четири нова полимерна комплекса
гвожђа(III) са 2,2′-бипиридином (bipy) и различитим ароматичним поликарбоксилатним лигандима, као што су анјони фталне (pht), изофталне (ipht), терефталне (tpht)
и пиромелитне (pyr) киселине. Комплекси су окарактерисани елементарном и TG/DSC
анализом, FTIR и дифузионо-рефлексионом UV–Vis–NIR спектроскопијом, као и магнетним мерењима. На основу аналитичких и спектралних података, утврђене су следеће
формуле комплекса: {[Fe4(bipy)2(H2O)2(OH)6(pht)3]·2H2O}n (1), {[Fe4(bipy)2(Hipht)2-
(ipht)2(OH)6]·4H2O}n (2), {[Fe4(bipy)2(Htpht)2(OH)6(tpht)2]·4H2O}n (3) и {[Fe4(bipy)-
(H2O)8(OH)4(pyr)2]·H2O}n (4). Сви комплекси су црвеномрке боје и нискоспински са
деформисаном октаедарском геометријом и хромофором типа FeO6 или FeN2O4. Поликарбоксилато лиганди имају мостовну улогу код свих једињења, међутим, док код 2 и 3
постоје монодентатне COO-
-групе, код 1 и 4 нађене су мостовне или хелатне COO–
групе. Детаљно је испитано термичко понашање комплекса 1–4 и израчунате су моларне
енталпије дехидратације. На основу свих добијених резултата, предложене су структурне формуле комплекса 1–4.
PB  - Srpsko hemijsko društvo
T2  - Journal of the Serbian Chemical Society
T1  - Synthesis and characterization of mu-hydroxido- and mu-polycarboxylato-bridged iron(III) complexes with 2,2 '-bipyridine
T1  - Синтеза и карактеризација гвожђе(III)-комплекса са μ-хидроксидо и μ-поликарбоксилато мостовима и 2,2′-бипиридином
EP  - 952
IS  - 8
SP  - 941
VL  - 79
DO  - 10.2298/JSC131028005T
ER  - 

@article{
author = "Tasić, Nikola and Rogan, Jelena and Poleti, Dejan and Radovanović, Lidija and Branković, Goran",
year = "2014",
abstract = "Four novel polymeric iron(III) complexes with 2,2'-bipyridine (bipy) and different aromatic polycarboxylato ligands as anions of phthalic (pht), isophthalic (ipht), terephthalic (tpht) and pyromellitic (pyr) acid were synthesized by ligand exchange reaction. The complexes were characterized by elemental and TG/DSC analysis, FTIR and diffuse reflectance UV-Vis-NIR spectroscopy and magnetic susceptibility measurements. Based on the analytical and spectral data, the formulae of the complexes were {[Fe-4(bipy)(2) (H2O)(2)(OH)(6)(pht)(3)]center dot 2H(2)O}(n) (1), {[Fe-4(bipy)(2)(Hipht)(2)(ipht)(2)(OH)(6)]center dot 4H(2)O}(n) (2), {[Fe-4(bipy)(2)(Htpht)(2)(OH)(6)(tpht)(2)]center dot 4H(2)O}(n) (3) and {[Fe-4(bipy)(H2O)(8)-(OH)(4)(pyr)(2)]center dot H2O}(n) (4). All complexes were red brown and low-spin with a distorted octahedral geometry with FeO6 or FeN2O4 chromophores. The polycarboxylato ligands played a bridging role in all cases, whereas monodentate COO groups were present in 2 and 3, while bridging and chelate COO groups were established in 1 and 4. The thermal behaviours of 1-4 were investigated in detail and the molar dehydration enthalpies were calculated. According to the all those results, the structural formulae of complexes 1-4 were proposed., Реакцијом измене лиганада синтетисана су четири нова полимерна комплекса
гвожђа(III) са 2,2′-бипиридином (bipy) и различитим ароматичним поликарбоксилатним лигандима, као што су анјони фталне (pht), изофталне (ipht), терефталне (tpht)
и пиромелитне (pyr) киселине. Комплекси су окарактерисани елементарном и TG/DSC
анализом, FTIR и дифузионо-рефлексионом UV–Vis–NIR спектроскопијом, као и магнетним мерењима. На основу аналитичких и спектралних података, утврђене су следеће
формуле комплекса: {[Fe4(bipy)2(H2O)2(OH)6(pht)3]·2H2O}n (1), {[Fe4(bipy)2(Hipht)2-
(ipht)2(OH)6]·4H2O}n (2), {[Fe4(bipy)2(Htpht)2(OH)6(tpht)2]·4H2O}n (3) и {[Fe4(bipy)-
(H2O)8(OH)4(pyr)2]·H2O}n (4). Сви комплекси су црвеномрке боје и нискоспински са
деформисаном октаедарском геометријом и хромофором типа FeO6 или FeN2O4. Поликарбоксилато лиганди имају мостовну улогу код свих једињења, међутим, док код 2 и 3
постоје монодентатне COO-
-групе, код 1 и 4 нађене су мостовне или хелатне COO–
групе. Детаљно је испитано термичко понашање комплекса 1–4 и израчунате су моларне
енталпије дехидратације. На основу свих добијених резултата, предложене су структурне формуле комплекса 1–4.",
publisher = "Srpsko hemijsko društvo",
journal = "Journal of the Serbian Chemical Society",
title = "Synthesis and characterization of mu-hydroxido- and mu-polycarboxylato-bridged iron(III) complexes with 2,2 '-bipyridine, Синтеза и карактеризација гвожђе(III)-комплекса са μ-хидроксидо и μ-поликарбоксилато мостовима и 2,2′-бипиридином",
pages = "952-941",
number = "8",
volume = "79",
doi = "10.2298/JSC131028005T"
}

Tasić, N., Rogan, J., Poleti, D., Radovanović, L.,& Branković, G.. (2014). Synthesis and characterization of mu-hydroxido- and mu-polycarboxylato-bridged iron(III) complexes with 2,2 '-bipyridine. in Journal of the Serbian Chemical Society
Srpsko hemijsko društvo., 79(8), 941-952.
https://doi.org/10.2298/JSC131028005T

Tasić N, Rogan J, Poleti D, Radovanović L, Branković G. Synthesis and characterization of mu-hydroxido- and mu-polycarboxylato-bridged iron(III) complexes with 2,2 '-bipyridine. in Journal of the Serbian Chemical Society. 2014;79(8):941-952.
doi:10.2298/JSC131028005T .

Tasić, Nikola, Rogan, Jelena, Poleti, Dejan, Radovanović, Lidija, Branković, Goran, "Synthesis and characterization of mu-hydroxido- and mu-polycarboxylato-bridged iron(III) complexes with 2,2 '-bipyridine" in Journal of the Serbian Chemical Society, 79, no. 8 (2014):941-952,
https://doi.org/10.2298/JSC131028005T . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Popov, Konstantin I.
AU  - Živković, Predrag M.
AU  - Branković, Goran
PY  - 2013
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5673
AB  - A new insight into the mechanism of lead electrodeposition from nitrate solutions is presented by analysis of the polarization characteristics and by scanning electron microscopic (SEM) analysis of the surface morphology of the lead deposits obtained in the potentiostatic regime of electrolysis. In dependence on the concentration of Pb(II) ions, the electrodeposition process is either mixed ohmic-diffusion or completely ohmic controlled. The ratio of the ohmic control to the total control of the electrodeposition process increased with increasing concentration of Pb(II) ions and at the higher concentrations of Pb(II) ions, the electrodeposition process became completely ohmic controlled. The polarization characteristics were well correlated with the morphologies of the obtained lead deposits. The formation of regular crystals was a characteristic of ohmic control of the electrodeposition process, while needle-like and fern-like dendrites were the predominant morphological forms obtained under diffusion control. The critical overpotentials for both dendritic growth initiation and instantaneous dendritic growth were analyzed and a mechanism of lead electrodeposition based on this analysis is presented. It was shown that the values of these critical overpotentials decreased and approached one another with increasing concentration of Pb(II) ions and finally became the same when full ohmic control was attained. The presented results were in good agreement with the predications of the general theory for the formation of disperse metal electrodeposits.
PB  - Elsevier
T2  - Journal of Electroanalytical Chemistry
T1  - A new insight into the mechanism of lead electrodeposition: Ohmic-diffusion control of the electrodeposition process
EP  - 76
SP  - 66
VL  - 691
DO  - 10.1016/j.jelechem.2012.12.011
ER  - 

@article{
author = "Nikolić, Nebojša D. and Popov, Konstantin I. and Živković, Predrag M. and Branković, Goran",
year = "2013",
abstract = "A new insight into the mechanism of lead electrodeposition from nitrate solutions is presented by analysis of the polarization characteristics and by scanning electron microscopic (SEM) analysis of the surface morphology of the lead deposits obtained in the potentiostatic regime of electrolysis. In dependence on the concentration of Pb(II) ions, the electrodeposition process is either mixed ohmic-diffusion or completely ohmic controlled. The ratio of the ohmic control to the total control of the electrodeposition process increased with increasing concentration of Pb(II) ions and at the higher concentrations of Pb(II) ions, the electrodeposition process became completely ohmic controlled. The polarization characteristics were well correlated with the morphologies of the obtained lead deposits. The formation of regular crystals was a characteristic of ohmic control of the electrodeposition process, while needle-like and fern-like dendrites were the predominant morphological forms obtained under diffusion control. The critical overpotentials for both dendritic growth initiation and instantaneous dendritic growth were analyzed and a mechanism of lead electrodeposition based on this analysis is presented. It was shown that the values of these critical overpotentials decreased and approached one another with increasing concentration of Pb(II) ions and finally became the same when full ohmic control was attained. The presented results were in good agreement with the predications of the general theory for the formation of disperse metal electrodeposits.",
publisher = "Elsevier",
journal = "Journal of Electroanalytical Chemistry",
title = "A new insight into the mechanism of lead electrodeposition: Ohmic-diffusion control of the electrodeposition process",
pages = "76-66",
volume = "691",
doi = "10.1016/j.jelechem.2012.12.011"
}

Nikolić, N. D., Popov, K. I., Živković, P. M.,& Branković, G.. (2013). A new insight into the mechanism of lead electrodeposition: Ohmic-diffusion control of the electrodeposition process. in Journal of Electroanalytical Chemistry
Elsevier., 691, 66-76.
https://doi.org/10.1016/j.jelechem.2012.12.011

Nikolić ND, Popov KI, Živković PM, Branković G. A new insight into the mechanism of lead electrodeposition: Ohmic-diffusion control of the electrodeposition process. in Journal of Electroanalytical Chemistry. 2013;691:66-76.
doi:10.1016/j.jelechem.2012.12.011 .

Nikolić, Nebojša D., Popov, Konstantin I., Živković, Predrag M., Branković, Goran, "A new insight into the mechanism of lead electrodeposition: Ohmic-diffusion control of the electrodeposition process" in Journal of Electroanalytical Chemistry, 691 (2013):66-76,
https://doi.org/10.1016/j.jelechem.2012.12.011 . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Vastag, Gyöngyi Gy.
AU  - Živković, Predrag M.
AU  - Jokić, Bojan
AU  - Branković, Goran
PY  - 2013
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5701
AB  - The processes of lead electrodeposition from the basic (nitrate) and complex (acetate) electrolytes were mutually compared by the analysis of their polarization characteristics and by the scanning electron microscopic (SEM) analysis of the morphology of formed deposits. Although the polarization characteristics of lead recorded from these two electrolytes were relatively similar to each other, the shape of formed dendrites strongly depended on the type of electrolyte. The dendrites composed of stalk and weak developed primary branches (the primary (P) type) were predominantly formed from the basic electrolyte. On the other hand, the very branchy dendrites composed of stalk and of both primary and secondary branches (the secondary (S) type) were mainly electrodeposited from the complex electrolyte. Considering the fact that the application of lead powder in many technologies is closely related with its surface morphology, the special attention was given to the analysis of the type of electrolytes on formation of the different dendritic forms. It was shown that formation of more branchy dendrites from the acetate electrolyte can be ascribed to the lower exchange current density (or to the lower rate of electrochemical process) for this electrolyte than for the nitrate one due to the process of complex formation.
PB  - Elsevier
T2  - Advanced Powder Technology
T1  - Influence of the complex formation on the morphology of lead powder particles produced by the electrodeposition processes
EP  - 682
IS  - 3
SP  - 674
VL  - 24
DO  - 10.1016/j.apt.2012.12.008
ER  - 

@article{
author = "Nikolić, Nebojša D. and Vastag, Gyöngyi Gy. and Živković, Predrag M. and Jokić, Bojan and Branković, Goran",
year = "2013",
abstract = "The processes of lead electrodeposition from the basic (nitrate) and complex (acetate) electrolytes were mutually compared by the analysis of their polarization characteristics and by the scanning electron microscopic (SEM) analysis of the morphology of formed deposits. Although the polarization characteristics of lead recorded from these two electrolytes were relatively similar to each other, the shape of formed dendrites strongly depended on the type of electrolyte. The dendrites composed of stalk and weak developed primary branches (the primary (P) type) were predominantly formed from the basic electrolyte. On the other hand, the very branchy dendrites composed of stalk and of both primary and secondary branches (the secondary (S) type) were mainly electrodeposited from the complex electrolyte. Considering the fact that the application of lead powder in many technologies is closely related with its surface morphology, the special attention was given to the analysis of the type of electrolytes on formation of the different dendritic forms. It was shown that formation of more branchy dendrites from the acetate electrolyte can be ascribed to the lower exchange current density (or to the lower rate of electrochemical process) for this electrolyte than for the nitrate one due to the process of complex formation.",
publisher = "Elsevier",
journal = "Advanced Powder Technology",
title = "Influence of the complex formation on the morphology of lead powder particles produced by the electrodeposition processes",
pages = "682-674",
number = "3",
volume = "24",
doi = "10.1016/j.apt.2012.12.008"
}

Nikolić, N. D., Vastag, G. Gy., Živković, P. M., Jokić, B.,& Branković, G.. (2013). Influence of the complex formation on the morphology of lead powder particles produced by the electrodeposition processes. in Advanced Powder Technology
Elsevier., 24(3), 674-682.
https://doi.org/10.1016/j.apt.2012.12.008

Nikolić ND, Vastag GG, Živković PM, Jokić B, Branković G. Influence of the complex formation on the morphology of lead powder particles produced by the electrodeposition processes. in Advanced Powder Technology. 2013;24(3):674-682.
doi:10.1016/j.apt.2012.12.008 .

Nikolić, Nebojša D., Vastag, Gyöngyi Gy., Živković, Predrag M., Jokić, Bojan, Branković, Goran, "Influence of the complex formation on the morphology of lead powder particles produced by the electrodeposition processes" in Advanced Powder Technology, 24, no. 3 (2013):674-682,
https://doi.org/10.1016/j.apt.2012.12.008 . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Maksimović, Vesna M.
AU  - Branković, Goran
AU  - Živković, Predrag M.
AU  - Pavlović, Miomir
PY  - 2013
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5702
AB  - Lead electrodeposition processes from basic (nitrate) and complex (acetate) electrolytes were mutually compared by scanning electron microscopy and X-ray diffraction investigation of the produced powder particles. The shape of dendritic particles strongly depended on the type of electrolyte. Dendrites composed of a stalk and weakly developed primary branches (the primary type) were predominantly formed from the basic electrolyte. Ramified dendrites composed of a stalk and of both primary and secondary branches (the secondary type) were mainly formed from the complex electrolyte. In both types of powder particles, Pb crystallites were predominantly oriented in the (111) plane. The formation of powder particles of different shapes with strong (111) preferred orientation is discussed and explained by consideration of the general characteristics of the growth of crystals in electrocrystallization processes.
AB  - Procesi elektrohemijskog taloženja olova iz osnovnog (nitratnog) i kompleksnog (acetatnog) elektrolita su bili međusobno upoređeni tehnikom skenirajuće elektronske mikroskopije i rendgensko-difrakcionom analizom proizvedenih čestica praha. Oblik dendritičnih čestica je snažno zavisio od tipa elektrolita. Dendriti sastavljeni od stabla i slabo razvijenih grana (primarni tip) su bili predominantno formirani iz osnovnog elektrolita. Razgranati dendriti sastavljeni od stabla i od primarnih i sekundarnih grana (sekundarni tip) su bili uglavnom formirani iz kompleksnog elektrolita. U oba tipa praškastih čestica kristaliti olova su bili dominantno orijentisani u (111) ravni. Formiranje praškastih čestica sa strogom (111) orijentacijom je bilo diskutovano i objašnjeno razmatranjem opštih karakteristika rasta kristala u procesima elektrokristalizacije.
PB  - Serbian Chemical Society
T2  - Journal of the Serbian Chemical Society
T1  - Influence of the type of electrolyte on the morphological and crystallographic characteristics of lead powder particles
T1  - Uticaj tipa elektrolita na morfološke i kristalografske karakteristike praškastih čestica olova
EP  - 1395
IS  - 9
SP  - 1387
VL  - 78
DO  - 10.2298/JSC130211034N
ER  - 

@article{
author = "Nikolić, Nebojša D. and Maksimović, Vesna M. and Branković, Goran and Živković, Predrag M. and Pavlović, Miomir",
year = "2013",
abstract = "Lead electrodeposition processes from basic (nitrate) and complex (acetate) electrolytes were mutually compared by scanning electron microscopy and X-ray diffraction investigation of the produced powder particles. The shape of dendritic particles strongly depended on the type of electrolyte. Dendrites composed of a stalk and weakly developed primary branches (the primary type) were predominantly formed from the basic electrolyte. Ramified dendrites composed of a stalk and of both primary and secondary branches (the secondary type) were mainly formed from the complex electrolyte. In both types of powder particles, Pb crystallites were predominantly oriented in the (111) plane. The formation of powder particles of different shapes with strong (111) preferred orientation is discussed and explained by consideration of the general characteristics of the growth of crystals in electrocrystallization processes., Procesi elektrohemijskog taloženja olova iz osnovnog (nitratnog) i kompleksnog (acetatnog) elektrolita su bili međusobno upoređeni tehnikom skenirajuće elektronske mikroskopije i rendgensko-difrakcionom analizom proizvedenih čestica praha. Oblik dendritičnih čestica je snažno zavisio od tipa elektrolita. Dendriti sastavljeni od stabla i slabo razvijenih grana (primarni tip) su bili predominantno formirani iz osnovnog elektrolita. Razgranati dendriti sastavljeni od stabla i od primarnih i sekundarnih grana (sekundarni tip) su bili uglavnom formirani iz kompleksnog elektrolita. U oba tipa praškastih čestica kristaliti olova su bili dominantno orijentisani u (111) ravni. Formiranje praškastih čestica sa strogom (111) orijentacijom je bilo diskutovano i objašnjeno razmatranjem opštih karakteristika rasta kristala u procesima elektrokristalizacije.",
publisher = "Serbian Chemical Society",
journal = "Journal of the Serbian Chemical Society",
title = "Influence of the type of electrolyte on the morphological and crystallographic characteristics of lead powder particles, Uticaj tipa elektrolita na morfološke i kristalografske karakteristike praškastih čestica olova",
pages = "1395-1387",
number = "9",
volume = "78",
doi = "10.2298/JSC130211034N"
}

Nikolić, N. D., Maksimović, V. M., Branković, G., Živković, P. M.,& Pavlović, M.. (2013). Influence of the type of electrolyte on the morphological and crystallographic characteristics of lead powder particles. in Journal of the Serbian Chemical Society
Serbian Chemical Society., 78(9), 1387-1395.
https://doi.org/10.2298/JSC130211034N

Nikolić ND, Maksimović VM, Branković G, Živković PM, Pavlović M. Influence of the type of electrolyte on the morphological and crystallographic characteristics of lead powder particles. in Journal of the Serbian Chemical Society. 2013;78(9):1387-1395.
doi:10.2298/JSC130211034N .

Nikolić, Nebojša D., Maksimović, Vesna M., Branković, Goran, Živković, Predrag M., Pavlović, Miomir, "Influence of the type of electrolyte on the morphological and crystallographic characteristics of lead powder particles" in Journal of the Serbian Chemical Society, 78, no. 9 (2013):1387-1395,
https://doi.org/10.2298/JSC130211034N . .

TY  - JOUR
AU  - Devečerski, Aleksandar
AU  - Pošarac, Milica B.
AU  - Dimitrijević, M.
AU  - Rosić, M.
AU  - Volkov-Husović, Tatjana
AU  - Branković, Goran
PY  - 2012
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2047
AB  - The silicon carbide powders are prepared by carbothermal reduction of domestic mineral resources (white and brown sepiolite), at relatively low temperatures (1200 - 1600oC). Carbothermal reduction process is greatly influenced by chemical composition of sepiolites and type of carbon used. Obtained SiC powders consist of fine β-SiC particles and did not retain the fibrous morphology of sepiolites. Catalytical influence of Fe is attributed to formation of iron-silicide and its potentionaly important role in removal of Mg-species, i.e. reduction of Mg2SiO4 and MgO into Mg(g).
AB  - Silicijum karbidni (SiC) prahovi su sintetisani metodom karbotermalne redukcije na relativno niskim temperaturama (1200-1600oS). Kao polazna sirovina odnosno izvor silicijuma, korišćene su domaće mineralne sirovine (beli sepiolit i braon sepiolit). Ustanovljeno je da i hemijski sastav sepiolita i tip korišćenog ugljenika (redukciono sredstvo), veoma utiču na sam proces karbotermalne redukcije. Dobijeni silicijum karbidni prahovi se sastoje od finih čestica beta silicijum karbida i nisu zadržali vlaknastu morfologiju polaznih sirovina tj. sepiolita. Opaženi katalitički uticaj gvožđa (Fe) je pripisan formiranju gvožđe silicida i njihovoj ulozi u olakšanom uklanjanju magnezijumovih jedinjenja (Mg2SiO4 i MgO), tj. redukciji istih u gasoviti magnezijum - Mg(g ).
PB  - International Institute for the Science of Sintering, Beograd
T2  - Science of Sintering
T1  - SiC synthesis using natural Mg-silicates
EP  - 94
IS  - 1
SP  - 81
VL  - 44
UR  - https://hdl.handle.net/21.15107/rcub_technorep_2047
ER  - 

@article{
author = "Devečerski, Aleksandar and Pošarac, Milica B. and Dimitrijević, M. and Rosić, M. and Volkov-Husović, Tatjana and Branković, Goran",
year = "2012",
abstract = "The silicon carbide powders are prepared by carbothermal reduction of domestic mineral resources (white and brown sepiolite), at relatively low temperatures (1200 - 1600oC). Carbothermal reduction process is greatly influenced by chemical composition of sepiolites and type of carbon used. Obtained SiC powders consist of fine β-SiC particles and did not retain the fibrous morphology of sepiolites. Catalytical influence of Fe is attributed to formation of iron-silicide and its potentionaly important role in removal of Mg-species, i.e. reduction of Mg2SiO4 and MgO into Mg(g)., Silicijum karbidni (SiC) prahovi su sintetisani metodom karbotermalne redukcije na relativno niskim temperaturama (1200-1600oS). Kao polazna sirovina odnosno izvor silicijuma, korišćene su domaće mineralne sirovine (beli sepiolit i braon sepiolit). Ustanovljeno je da i hemijski sastav sepiolita i tip korišćenog ugljenika (redukciono sredstvo), veoma utiču na sam proces karbotermalne redukcije. Dobijeni silicijum karbidni prahovi se sastoje od finih čestica beta silicijum karbida i nisu zadržali vlaknastu morfologiju polaznih sirovina tj. sepiolita. Opaženi katalitički uticaj gvožđa (Fe) je pripisan formiranju gvožđe silicida i njihovoj ulozi u olakšanom uklanjanju magnezijumovih jedinjenja (Mg2SiO4 i MgO), tj. redukciji istih u gasoviti magnezijum - Mg(g ).",
publisher = "International Institute for the Science of Sintering, Beograd",
journal = "Science of Sintering",
title = "SiC synthesis using natural Mg-silicates",
pages = "94-81",
number = "1",
volume = "44",
url = "https://hdl.handle.net/21.15107/rcub_technorep_2047"
}

Devečerski, A., Pošarac, M. B., Dimitrijević, M., Rosić, M., Volkov-Husović, T.,& Branković, G.. (2012). SiC synthesis using natural Mg-silicates. in Science of Sintering
International Institute for the Science of Sintering, Beograd., 44(1), 81-94.
https://hdl.handle.net/21.15107/rcub_technorep_2047

Devečerski A, Pošarac MB, Dimitrijević M, Rosić M, Volkov-Husović T, Branković G. SiC synthesis using natural Mg-silicates. in Science of Sintering. 2012;44(1):81-94.
https://hdl.handle.net/21.15107/rcub_technorep_2047 .

Devečerski, Aleksandar, Pošarac, Milica B., Dimitrijević, M., Rosić, M., Volkov-Husović, Tatjana, Branković, Goran, "SiC synthesis using natural Mg-silicates" in Science of Sintering, 44, no. 1 (2012):81-94,
https://hdl.handle.net/21.15107/rcub_technorep_2047 .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Branković, Goran
AU  - Popov, Konstantin I.
PY  - 2011
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5648
AB  - Optimization of process of formation of open and porous copper electrodes, denoted as the honeycomb-like ones, by the regime of pulsating current (PC) is considered. The square-waves PC were consisted of the same amplitude current density and pause duration of 10 ms, while the analyzed deposition pulses were: 1, 4, 7, 10 and 20 ms. Morphologies of electrodeposited copper and the quantities of evolved hydrogen during electrodeposition processes were compared with the surface morphology and the quantity of evolved hydrogen obtained by copper electrodeposition in the galvanostatic mode. In galvanostatic mode, electrodeposition of copper was performed at a current density which corresponded to the amplitude current density in the PC regimes. Honeycomb-like deposits were formed at the constant current density and by the PC regimes with deposition pulses of 7, 10 and 20 ms. The mixture of holes constructing the honeycomb-like structure and dish-like holes was obtained with a deposition pulse of 4 ms. Finally, dish-like holes were only formed with a deposition pulse of 1 ms. The change of the shape of holes was discussed by the change of hydrodynamic conditions in the near-electrode layer caused by evolved hydrogen. The specific energy consumption in the PC regimes of electrolysis was also discussed. Analysis of the specific energy consumption showed that energy saving of about 15% can be attained in the production of honeycomb-like electrodes by the choice of the appropriate PC regime.
PB  - Elsevier Science Sa, Lausanne
T2  - Materials Chemistry and Physics
T1  - Optimization of electrolytic process of formation of open and porous copper electrodes by the pulsating current (PC) regime
EP  - 594
IS  - 3
SP  - 587
VL  - 125
DO  - 10.1016/j.matchemphys.2010.10.013
ER  - 

@article{
author = "Nikolić, Nebojša D. and Branković, Goran and Popov, Konstantin I.",
year = "2011",
abstract = "Optimization of process of formation of open and porous copper electrodes, denoted as the honeycomb-like ones, by the regime of pulsating current (PC) is considered. The square-waves PC were consisted of the same amplitude current density and pause duration of 10 ms, while the analyzed deposition pulses were: 1, 4, 7, 10 and 20 ms. Morphologies of electrodeposited copper and the quantities of evolved hydrogen during electrodeposition processes were compared with the surface morphology and the quantity of evolved hydrogen obtained by copper electrodeposition in the galvanostatic mode. In galvanostatic mode, electrodeposition of copper was performed at a current density which corresponded to the amplitude current density in the PC regimes. Honeycomb-like deposits were formed at the constant current density and by the PC regimes with deposition pulses of 7, 10 and 20 ms. The mixture of holes constructing the honeycomb-like structure and dish-like holes was obtained with a deposition pulse of 4 ms. Finally, dish-like holes were only formed with a deposition pulse of 1 ms. The change of the shape of holes was discussed by the change of hydrodynamic conditions in the near-electrode layer caused by evolved hydrogen. The specific energy consumption in the PC regimes of electrolysis was also discussed. Analysis of the specific energy consumption showed that energy saving of about 15% can be attained in the production of honeycomb-like electrodes by the choice of the appropriate PC regime.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Materials Chemistry and Physics",
title = "Optimization of electrolytic process of formation of open and porous copper electrodes by the pulsating current (PC) regime",
pages = "594-587",
number = "3",
volume = "125",
doi = "10.1016/j.matchemphys.2010.10.013"
}

Nikolić, N. D., Branković, G.,& Popov, K. I.. (2011). Optimization of electrolytic process of formation of open and porous copper electrodes by the pulsating current (PC) regime. in Materials Chemistry and Physics
Elsevier Science Sa, Lausanne., 125(3), 587-594.
https://doi.org/10.1016/j.matchemphys.2010.10.013

Nikolić ND, Branković G, Popov KI. Optimization of electrolytic process of formation of open and porous copper electrodes by the pulsating current (PC) regime. in Materials Chemistry and Physics. 2011;125(3):587-594.
doi:10.1016/j.matchemphys.2010.10.013 .

Nikolić, Nebojša D., Branković, Goran, Popov, Konstantin I., "Optimization of electrolytic process of formation of open and porous copper electrodes by the pulsating current (PC) regime" in Materials Chemistry and Physics, 125, no. 3 (2011):587-594,
https://doi.org/10.1016/j.matchemphys.2010.10.013 . .

TY  - JOUR
AU  - Popov, Konstantin I
AU  - Nikolic, Nebojša D
AU  - Živković, Predrag M.
AU  - Branković, Goran
PY  - 2010
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5618
AB  - In this study, it is considered: (a) the effect of the exchange current density to the limiting diffusion current density ratio (J(0)/J(L)) at low level of surface coarseness on the polarization characteristics of the electrochemical process, (b) the effect of the shape of surface protrusions oil the electrode surface roughness, and (c) the effect of surface roughness oil the J(0)/J(L) ratio. It was shown that the increase of the value of the j(0)/J(L) ratio produces a decrease of overpotential at fixed value of current density. At selected set of conditions, the j(0)/j(L) ratio cats be increased by the increase of roughness of electrode surface by electrodeposition of disperse deposits at low level of coarseness The increase of the value of the J(0)/J(L) ratio produces large saving of energy required for the evaluation of electrochemical reaction The conditions in which the electrochemical process cats become Ohmic controlled were also specified.
PB  - Pergamon-Elsevier Science Ltd, Oxford
T2  - Electrochimica Acta
T1  - The effect of the electrode surface roughness at low level of coarseness on the polarization characteristics of electrochemical processes
EP  - 1925
IS  - 6
SP  - 1919
VL  - 55
DO  - 10.1016/j.electacta.2009.10.085
ER  - 

@article{
author = "Popov, Konstantin I and Nikolic, Nebojša D and Živković, Predrag M. and Branković, Goran",
year = "2010",
abstract = "In this study, it is considered: (a) the effect of the exchange current density to the limiting diffusion current density ratio (J(0)/J(L)) at low level of surface coarseness on the polarization characteristics of the electrochemical process, (b) the effect of the shape of surface protrusions oil the electrode surface roughness, and (c) the effect of surface roughness oil the J(0)/J(L) ratio. It was shown that the increase of the value of the j(0)/J(L) ratio produces a decrease of overpotential at fixed value of current density. At selected set of conditions, the j(0)/j(L) ratio cats be increased by the increase of roughness of electrode surface by electrodeposition of disperse deposits at low level of coarseness The increase of the value of the J(0)/J(L) ratio produces large saving of energy required for the evaluation of electrochemical reaction The conditions in which the electrochemical process cats become Ohmic controlled were also specified.",
publisher = "Pergamon-Elsevier Science Ltd, Oxford",
journal = "Electrochimica Acta",
title = "The effect of the electrode surface roughness at low level of coarseness on the polarization characteristics of electrochemical processes",
pages = "1925-1919",
number = "6",
volume = "55",
doi = "10.1016/j.electacta.2009.10.085"
}

Popov, K. I., Nikolic, N. D., Živković, P. M.,& Branković, G.. (2010). The effect of the electrode surface roughness at low level of coarseness on the polarization characteristics of electrochemical processes. in Electrochimica Acta
Pergamon-Elsevier Science Ltd, Oxford., 55(6), 1919-1925.
https://doi.org/10.1016/j.electacta.2009.10.085

Popov KI, Nikolic ND, Živković PM, Branković G. The effect of the electrode surface roughness at low level of coarseness on the polarization characteristics of electrochemical processes. in Electrochimica Acta. 2010;55(6):1919-1925.
doi:10.1016/j.electacta.2009.10.085 .

Popov, Konstantin I, Nikolic, Nebojša D, Živković, Predrag M., Branković, Goran, "The effect of the electrode surface roughness at low level of coarseness on the polarization characteristics of electrochemical processes" in Electrochimica Acta, 55, no. 6 (2010):1919-1925,
https://doi.org/10.1016/j.electacta.2009.10.085 . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Branković, Goran
AU  - Pavlović, Miomir
AU  - Popov, Konstantin I.
PY  - 2009
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5541
AB  - The formation of honeycomb-like structures in the pulsating overpotential (PO) regime was examined by scanning electron microscopy (SEM). The honeycomb-like structures obtained with a square-wave PO of different pause to pulse ratios were compared to the one obtained in the constant potentiostatic regime. Increasing the pause to pulse ratio led to a decrease of the diameter of the holes formed by attached hydrogen bubbles, as well as to an increase in the number of holes formed at the surface area of copper electrodes. The size of the agglomerates of copper grains, of which the walls of the holes were constructed, was reduced with increasing duration of the pause. Also, the uniformity of the honeycomb-like structures was increased by application of the PO regime. It was shown that the effects attained by application of this regime were comparable with those obtained by electrodeposition in a constant potential regime with the addition of specific additives.
PB  - Elsevier Science Inc, New York
T2  - Electrochemistry Communications
T1  - The effects of the pause to pulse ratio in the regime of pulsating overpotential on the formation of honeycomb-like structures
EP  - 424
IS  - 2
SP  - 421
VL  - 11
DO  - 10.1016/j.elecom.2008.12.007
ER  - 

@article{
author = "Nikolić, Nebojša D. and Branković, Goran and Pavlović, Miomir and Popov, Konstantin I.",
year = "2009",
abstract = "The formation of honeycomb-like structures in the pulsating overpotential (PO) regime was examined by scanning electron microscopy (SEM). The honeycomb-like structures obtained with a square-wave PO of different pause to pulse ratios were compared to the one obtained in the constant potentiostatic regime. Increasing the pause to pulse ratio led to a decrease of the diameter of the holes formed by attached hydrogen bubbles, as well as to an increase in the number of holes formed at the surface area of copper electrodes. The size of the agglomerates of copper grains, of which the walls of the holes were constructed, was reduced with increasing duration of the pause. Also, the uniformity of the honeycomb-like structures was increased by application of the PO regime. It was shown that the effects attained by application of this regime were comparable with those obtained by electrodeposition in a constant potential regime with the addition of specific additives.",
publisher = "Elsevier Science Inc, New York",
journal = "Electrochemistry Communications",
title = "The effects of the pause to pulse ratio in the regime of pulsating overpotential on the formation of honeycomb-like structures",
pages = "424-421",
number = "2",
volume = "11",
doi = "10.1016/j.elecom.2008.12.007"
}

Nikolić, N. D., Branković, G., Pavlović, M.,& Popov, K. I.. (2009). The effects of the pause to pulse ratio in the regime of pulsating overpotential on the formation of honeycomb-like structures. in Electrochemistry Communications
Elsevier Science Inc, New York., 11(2), 421-424.
https://doi.org/10.1016/j.elecom.2008.12.007

Nikolić ND, Branković G, Pavlović M, Popov KI. The effects of the pause to pulse ratio in the regime of pulsating overpotential on the formation of honeycomb-like structures. in Electrochemistry Communications. 2009;11(2):421-424.
doi:10.1016/j.elecom.2008.12.007 .

Nikolić, Nebojša D., Branković, Goran, Pavlović, Miomir, Popov, Konstantin I., "The effects of the pause to pulse ratio in the regime of pulsating overpotential on the formation of honeycomb-like structures" in Electrochemistry Communications, 11, no. 2 (2009):421-424,
https://doi.org/10.1016/j.elecom.2008.12.007 . .

TY  - JOUR
AU  - Nikolić, Nebojša D.
AU  - Branković, Goran
AU  - Pavlović, Miomir
AU  - Popov, Konstantin I.
PY  - 2008
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5579
AB  - Formation of irregular deposits by electrodeposition from acid sulfate solutions of various H2SO4 concentrations was examined by the determination of the average current efficiency of hydrogen evolution and by the scanning electron microscopic (SEM) analysis of the copper deposits morphology. Copper dendrites were the dominant morphological form obtained at overpotentials corresponding to the plateaus of the limiting diffusion current density. The number of the formed dendrites was increasing with the decreasing H2SO4 concentration. Holes formed due to the attached hydrogen bubbles were the basic morphological form of electrodeposited copper from all analyzed copper sulfate solutions at overpotentials outside the plateau of the limiting diffusion current density. The honeycomb-like structures (holes of the detached hydrogen bubbles with cauliflower-like agglomerates of copper grains between them) were formed if electrodepositions were performed from 0.15 M CuSO4 in both 0.250 M and 1.0 M H2SO4. On the other hand, aside from the holes and cauliflower-like forms, electrodeposition from 0.15 M CuSO4 in 0.125 M H2SO4 led to the formation of degenerated dendrites and dendritic particles inside channels formed of evolved hydrogen. Holes with shoulders of degenerated dendrites were also formed. The formation of different morphological forms under hydrogen co-deposition was discussed in the terms of hydrodynamic conditions in the near-electrode layer using the values for the break-off diameter of hydrogen bubbles.
PB  - Elsevier
T2  - Journal of Electroanalytical Chemistry
T1  - The effect of hydrogen co-deposition on the morphology of copper electrodeposits. II. Correlation between the properties of electrolytic solutions and the quantity of evolved hydrogen
EP  - 21
IS  - 1
SP  - 13
VL  - 621
DO  - 10.1016/j.jelechem.2008.04.006
ER  - 

@article{
author = "Nikolić, Nebojša D. and Branković, Goran and Pavlović, Miomir and Popov, Konstantin I.",
year = "2008",
abstract = "Formation of irregular deposits by electrodeposition from acid sulfate solutions of various H2SO4 concentrations was examined by the determination of the average current efficiency of hydrogen evolution and by the scanning electron microscopic (SEM) analysis of the copper deposits morphology. Copper dendrites were the dominant morphological form obtained at overpotentials corresponding to the plateaus of the limiting diffusion current density. The number of the formed dendrites was increasing with the decreasing H2SO4 concentration. Holes formed due to the attached hydrogen bubbles were the basic morphological form of electrodeposited copper from all analyzed copper sulfate solutions at overpotentials outside the plateau of the limiting diffusion current density. The honeycomb-like structures (holes of the detached hydrogen bubbles with cauliflower-like agglomerates of copper grains between them) were formed if electrodepositions were performed from 0.15 M CuSO4 in both 0.250 M and 1.0 M H2SO4. On the other hand, aside from the holes and cauliflower-like forms, electrodeposition from 0.15 M CuSO4 in 0.125 M H2SO4 led to the formation of degenerated dendrites and dendritic particles inside channels formed of evolved hydrogen. Holes with shoulders of degenerated dendrites were also formed. The formation of different morphological forms under hydrogen co-deposition was discussed in the terms of hydrodynamic conditions in the near-electrode layer using the values for the break-off diameter of hydrogen bubbles.",
publisher = "Elsevier",
journal = "Journal of Electroanalytical Chemistry",
title = "The effect of hydrogen co-deposition on the morphology of copper electrodeposits. II. Correlation between the properties of electrolytic solutions and the quantity of evolved hydrogen",
pages = "21-13",
number = "1",
volume = "621",
doi = "10.1016/j.jelechem.2008.04.006"
}

Nikolić, N. D., Branković, G., Pavlović, M.,& Popov, K. I.. (2008). The effect of hydrogen co-deposition on the morphology of copper electrodeposits. II. Correlation between the properties of electrolytic solutions and the quantity of evolved hydrogen. in Journal of Electroanalytical Chemistry
Elsevier., 621(1), 13-21.
https://doi.org/10.1016/j.jelechem.2008.04.006

Nikolić ND, Branković G, Pavlović M, Popov KI. The effect of hydrogen co-deposition on the morphology of copper electrodeposits. II. Correlation between the properties of electrolytic solutions and the quantity of evolved hydrogen. in Journal of Electroanalytical Chemistry. 2008;621(1):13-21.
doi:10.1016/j.jelechem.2008.04.006 .

Nikolić, Nebojša D., Branković, Goran, Pavlović, Miomir, Popov, Konstantin I., "The effect of hydrogen co-deposition on the morphology of copper electrodeposits. II. Correlation between the properties of electrolytic solutions and the quantity of evolved hydrogen" in Journal of Electroanalytical Chemistry, 621, no. 1 (2008):13-21,
https://doi.org/10.1016/j.jelechem.2008.04.006 . .