TY  - CONF
AU  - Popović, Miljana
AU  - Alil, Ana
AU  - Gligorijević, Bojan
AU  - Romhanji, Endre
PY  - 2023
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/7296
AB  - Wrought Al-Mg alloys are important and promising material for application in transportation industry primarily due to favorable strength to weight ratio. As a result of their usage in the field of transportation, the weight of vehicle constructions become reduced, resulting in a decrease of fuel consumption and carbon dioxide emissions. In addition to these advantages, one of the important demands on the application of Al-Mg alloys as a light weight structural material, is providing a high strength, corrosion resistance and good surface quality without relief caused by yield point phenomena and serrated flow. Such a good combination of properties can be achieved by a variation and optimization of thermomechanical processing parameters including a degree of deformation and annealing conditions. 
In this study we investigated the effect of cold rolling reductions and different annealing conditions, on the corrosion resistance and mechanical properties of an AA5182 type Al-Mg alloy. Material was industrially produced and supplied by Impol-Seval Aluminium Rolling Mill, Sevojno, Serbia, as hot rolled 12 mm thick plates. Further lab-processing of hot rolled plates included cold rolling with 40-85% reduction in thickness, and annealing in the range of temperatures 280-350°C, in a different period of time. Annealed specimens were used for room temperature tensile testing while corrosion testing was performed on the annealed and sensitized specimens. Intergranular corrosion (IGC) susceptibility was determined by nitric acid mass loss test (NAMLT) for the selected states. 
The results showed that corrosion resistance, tensile strength and yield point elongation were mostly affected by a degree of cold deformation. It was found that increasing in cold rolling reduction from 40-85% before annealing causes an improved strength level due to grain size refinement. However, yield point elongation became more pronounced and a tendency towards Lüdering as undesirable surface appearance was increased. NAMLT testing showed that the material was corrosion resistant in as-annealed condition while it became susceptible to intergranular corrosion after sensitization treatment. IGC susceptibility of sensitized specimens increases with cold rolling reduction and a raise of annealing temperature.
PB  - Belgrade : Association of Metallurgical Engineers of Serbia (AMES)
C3  - Book of Abstracts / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023
T1  - Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy
SP  - 51
UR  - https://hdl.handle.net/21.15107/rcub_technorep_7296
ER  - 

@conference{
author = "Popović, Miljana and Alil, Ana and Gligorijević, Bojan and Romhanji, Endre",
year = "2023",
abstract = "Wrought Al-Mg alloys are important and promising material for application in transportation industry primarily due to favorable strength to weight ratio. As a result of their usage in the field of transportation, the weight of vehicle constructions become reduced, resulting in a decrease of fuel consumption and carbon dioxide emissions. In addition to these advantages, one of the important demands on the application of Al-Mg alloys as a light weight structural material, is providing a high strength, corrosion resistance and good surface quality without relief caused by yield point phenomena and serrated flow. Such a good combination of properties can be achieved by a variation and optimization of thermomechanical processing parameters including a degree of deformation and annealing conditions. 
In this study we investigated the effect of cold rolling reductions and different annealing conditions, on the corrosion resistance and mechanical properties of an AA5182 type Al-Mg alloy. Material was industrially produced and supplied by Impol-Seval Aluminium Rolling Mill, Sevojno, Serbia, as hot rolled 12 mm thick plates. Further lab-processing of hot rolled plates included cold rolling with 40-85% reduction in thickness, and annealing in the range of temperatures 280-350°C, in a different period of time. Annealed specimens were used for room temperature tensile testing while corrosion testing was performed on the annealed and sensitized specimens. Intergranular corrosion (IGC) susceptibility was determined by nitric acid mass loss test (NAMLT) for the selected states. 
The results showed that corrosion resistance, tensile strength and yield point elongation were mostly affected by a degree of cold deformation. It was found that increasing in cold rolling reduction from 40-85% before annealing causes an improved strength level due to grain size refinement. However, yield point elongation became more pronounced and a tendency towards Lüdering as undesirable surface appearance was increased. NAMLT testing showed that the material was corrosion resistant in as-annealed condition while it became susceptible to intergranular corrosion after sensitization treatment. IGC susceptibility of sensitized specimens increases with cold rolling reduction and a raise of annealing temperature.",
publisher = "Belgrade : Association of Metallurgical Engineers of Serbia (AMES)",
journal = "Book of Abstracts / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023",
title = "Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy",
pages = "51",
url = "https://hdl.handle.net/21.15107/rcub_technorep_7296"
}

Popović, M., Alil, A., Gligorijević, B.,& Romhanji, E.. (2023). Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy. in Book of Abstracts / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023
Belgrade : Association of Metallurgical Engineers of Serbia (AMES)., 51.
https://hdl.handle.net/21.15107/rcub_technorep_7296

Popović M, Alil A, Gligorijević B, Romhanji E. Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy. in Book of Abstracts / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023. 2023;:51.
https://hdl.handle.net/21.15107/rcub_technorep_7296 .

Popović, Miljana, Alil, Ana, Gligorijević, Bojan, Romhanji, Endre, "Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy" in Book of Abstracts / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023 (2023):51,
https://hdl.handle.net/21.15107/rcub_technorep_7296 .

TY  - CONF
AU  - Popović, Miljana
AU  - Alil, Ana
AU  - Gligorijević, Bojan
AU  - Romhanji, Endre
PY  - 2023
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/7295
AB  - In this study we investigated the effect of cold rolling reductions and different annealing conditions, on the mechanical properties and corrosion resistance of an AA5182 type Al-Mg alloy. Material was industrially produced and supplied as hot rolled 12 mm thick plates. Further lab-processing included cold rolling with 40-85% reduction in thickness, and 2h of annealing in the range of temperatures from 300-350°C. Annealed specimens were used for room temperature tensile testing while corrosion testing was performed on the annealed and sensitized specimens. Intergranular corrosion (IGC) susceptibility was determined by nitric acid mass loss test (NAMLT) for the selected states. 
The results showed that corrosion resistance, tensile strength and yield point elongation were mostly affected by a degree of cold deformation. It was found that increasing in cold rolling reduction from 40-85% before annealing causes an improved strength level due to grain size refinement. However, yield point elongation became more pronounced and a tendency towards Lüdering as undesirable surface appearance was increased. NAMLT testing showed that the material was corrosion resistant in as-annealed condition while it became susceptible to intergranular corrosion after sensitization treatment. IGC susceptibility of sensitized specimens increases with cold rolling reduction and a grain size refinement.
PB  - Belgrade : Association of Metallurgical Engineers of Serbia (AMES)
C3  - Congress Proceedings / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023
T1  - Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy
EP  - 297
SP  - 291
UR  - https://hdl.handle.net/21.15107/rcub_technorep_7295
ER  - 

@conference{
author = "Popović, Miljana and Alil, Ana and Gligorijević, Bojan and Romhanji, Endre",
year = "2023",
abstract = "In this study we investigated the effect of cold rolling reductions and different annealing conditions, on the mechanical properties and corrosion resistance of an AA5182 type Al-Mg alloy. Material was industrially produced and supplied as hot rolled 12 mm thick plates. Further lab-processing included cold rolling with 40-85% reduction in thickness, and 2h of annealing in the range of temperatures from 300-350°C. Annealed specimens were used for room temperature tensile testing while corrosion testing was performed on the annealed and sensitized specimens. Intergranular corrosion (IGC) susceptibility was determined by nitric acid mass loss test (NAMLT) for the selected states. 
The results showed that corrosion resistance, tensile strength and yield point elongation were mostly affected by a degree of cold deformation. It was found that increasing in cold rolling reduction from 40-85% before annealing causes an improved strength level due to grain size refinement. However, yield point elongation became more pronounced and a tendency towards Lüdering as undesirable surface appearance was increased. NAMLT testing showed that the material was corrosion resistant in as-annealed condition while it became susceptible to intergranular corrosion after sensitization treatment. IGC susceptibility of sensitized specimens increases with cold rolling reduction and a grain size refinement.",
publisher = "Belgrade : Association of Metallurgical Engineers of Serbia (AMES)",
journal = "Congress Proceedings / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023",
title = "Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy",
pages = "297-291",
url = "https://hdl.handle.net/21.15107/rcub_technorep_7295"
}

Popović, M., Alil, A., Gligorijević, B.,& Romhanji, E.. (2023). Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy. in Congress Proceedings / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023
Belgrade : Association of Metallurgical Engineers of Serbia (AMES)., 291-297.
https://hdl.handle.net/21.15107/rcub_technorep_7295

Popović M, Alil A, Gligorijević B, Romhanji E. Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy. in Congress Proceedings / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023. 2023;:291-297.
https://hdl.handle.net/21.15107/rcub_technorep_7295 .

Popović, Miljana, Alil, Ana, Gligorijević, Bojan, Romhanji, Endre, "Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy" in Congress Proceedings / 5th Metallurgical & Materials Engineering Congress of South-East Europe MME SEE Congress 2023, Trebinje, Bosnia and Herzegovina 7-10th June 2023 (2023):291-297,
https://hdl.handle.net/21.15107/rcub_technorep_7295 .

TY  - JOUR
AU  - Gligorijević, Bojan R.
AU  - Vilotijević, Miroljub N.
PY  - 2022
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6638
AB  - The current study focuses on creating an initial highly alkaline simulated body fluid whose pH can be decreased to a physiological range by adding CO2 (protein-free simulated body fluid) or a combination of CO2 and human proteins (protein-containing simulated body fluid). The effects of dissolved human proteins, Ca2+ ions, and immersed plasma-sprayed hydroxyapatite coatings on the pH and chemical instability of prepared simulated body fluids were investigated. The physiological concentration of dissolved human proteins decreased the pH instability in prepared simulated body fluids by 60% and the physiological concentration of dissolved Ca2+ ions by 15%. The effect of immersing the hydroxyapatite coatings was negligible. In terms of chemical instability, the dissolution of Ca2+ ions caused the blurring of protein-free simulated body fluids after 0.6-1.0 h. In protein-containing simulated body fluids, this phenomenon was undetectable due to their opacity. The effects of human protein presence on the carbonated-apatite-forming ability on the surfaces of immersed hydroxyapatite coatings in the prepared simulated body fluids were also assessed. The experiments validated the bioactivity of plasma-sprayed hydroxyapatite coatings in the prepared simulated body fluids, regardless of protein presence. On the other hand, under the different experimental conditions (unregulated or regulated pH), the human protein presence had an inhibitory (unregulated pH) or indifferent/promoting (regulated pH) influence on the carbonated-apatite-forming ability. The results of the present study are discussed, as well as the strengths and shortcomings of the prepared simulated body fluids, and are compared to those of previous relevant investigations.
PB  - Iranian Institute of Research and Development in Chemical Industries
T2  - Iranian Journal of Chemistry and Chemical Engineering
T1  - Simulated Body Fluids Prepared with Natural Buffers and System for Active pH Regulation
EP  - 2935
IS  - 9
SP  - 2918
VL  - 41
DO  - 10.30492/ijcce.2021.530070.4823
ER  - 

@article{
author = "Gligorijević, Bojan R. and Vilotijević, Miroljub N.",
year = "2022",
abstract = "The current study focuses on creating an initial highly alkaline simulated body fluid whose pH can be decreased to a physiological range by adding CO2 (protein-free simulated body fluid) or a combination of CO2 and human proteins (protein-containing simulated body fluid). The effects of dissolved human proteins, Ca2+ ions, and immersed plasma-sprayed hydroxyapatite coatings on the pH and chemical instability of prepared simulated body fluids were investigated. The physiological concentration of dissolved human proteins decreased the pH instability in prepared simulated body fluids by 60% and the physiological concentration of dissolved Ca2+ ions by 15%. The effect of immersing the hydroxyapatite coatings was negligible. In terms of chemical instability, the dissolution of Ca2+ ions caused the blurring of protein-free simulated body fluids after 0.6-1.0 h. In protein-containing simulated body fluids, this phenomenon was undetectable due to their opacity. The effects of human protein presence on the carbonated-apatite-forming ability on the surfaces of immersed hydroxyapatite coatings in the prepared simulated body fluids were also assessed. The experiments validated the bioactivity of plasma-sprayed hydroxyapatite coatings in the prepared simulated body fluids, regardless of protein presence. On the other hand, under the different experimental conditions (unregulated or regulated pH), the human protein presence had an inhibitory (unregulated pH) or indifferent/promoting (regulated pH) influence on the carbonated-apatite-forming ability. The results of the present study are discussed, as well as the strengths and shortcomings of the prepared simulated body fluids, and are compared to those of previous relevant investigations.",
publisher = "Iranian Institute of Research and Development in Chemical Industries",
journal = "Iranian Journal of Chemistry and Chemical Engineering",
title = "Simulated Body Fluids Prepared with Natural Buffers and System for Active pH Regulation",
pages = "2935-2918",
number = "9",
volume = "41",
doi = "10.30492/ijcce.2021.530070.4823"
}

Gligorijević, B. R.,& Vilotijević, M. N.. (2022). Simulated Body Fluids Prepared with Natural Buffers and System for Active pH Regulation. in Iranian Journal of Chemistry and Chemical Engineering
Iranian Institute of Research and Development in Chemical Industries., 41(9), 2918-2935.
https://doi.org/10.30492/ijcce.2021.530070.4823

Gligorijević BR, Vilotijević MN. Simulated Body Fluids Prepared with Natural Buffers and System for Active pH Regulation. in Iranian Journal of Chemistry and Chemical Engineering. 2022;41(9):2918-2935.
doi:10.30492/ijcce.2021.530070.4823 .

Gligorijević, Bojan R., Vilotijević, Miroljub N., "Simulated Body Fluids Prepared with Natural Buffers and System for Active pH Regulation" in Iranian Journal of Chemistry and Chemical Engineering, 41, no. 9 (2022):2918-2935,
https://doi.org/10.30492/ijcce.2021.530070.4823 . .

TY  - JOUR
AU  - Vuksanović, Marija M.
AU  - Tomić, Nataša
AU  - Mladenović, Ivana
AU  - Perić, Tamara
AU  - Gligorijević, Bojan
AU  - Jančić-Heinemann, Radmila
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4559
AB  - Composite materials based on acrylate UV-cured polymers (Bis-GMA/TEGDMA) as a matrix and reinforcements that can be selected in order to adjust the properties of the obtained composite are used in the field of dental technology. The role of reinforcement is to adjust the mechanical properties, but also to control the shrinkage during curing. As reinforcement, alumina particles doped with iron oxide (Al2O3 Fe) synthesized using the sol-gel technique were selected. In order to simulate the process of adhesive application in real conditions, in vitro testing technique and adhesion properties of synthesized adhesive were used, where tooth tissue was used as a substrate. Comparison with standard adhesives used in dentistry was used to compare adhesion. The quality of the adhesive joint was evaluated using the microhardness testing method using different loads where it is estimated how the adhesive makes a connection with the substrate. It was shown that the synthesized adhesive showed significantly enhanced adhesion compared to the standard adhesive used in dentistry (836%).
AB  - Kompozitni materijali na bazi akrilatnih fotopolimerizujućih polimera, (Bis-GMA/TEGDMA) koji predstavljaju matricu i ojačanja koja se mogu odabrati sa ciljem podešavanja svojstava dobijenih kompozita, koriste se u oblasti dentalne tehnologije. Uloga ojačanja je podešavanje mehaničkih svojstava, ali i kontrola skupljanja tokom očvršćavanja. Kao ojačanje odabrane su čestice aluminijum-oksida dopirane gvožđe oksidom (Al2O3 Fe), sintetisane korišćenjem sol-gel tehnike. U cilju simuliranja procesa primene adheziva u realnim uslovima korišćena je in vitro tehnika ispitivanja adhezije sintetisanog adheziva pri čemu je kao substrat korišćeno tkivo zuba. Dobijene vrednosti adhezije poređene su sa komercijalnim adhezivima koji se koriste u stomatologiji. Kvalitet adhezivnog spoja ocenjen je merenjem mikrotvrdoće primenom različitih opterećenja, pri čemu je procenjen način kako se ostvaruje spoj između filma i podloge. Pokazalo se da je sintetisani adheziv imao višestruko jaču adheziju u poređenju sa standardnim adhezivom korišćenim u stomatologiji (836 %).
PB  - Savez inženjera i tehničara Srbije, Beograd
T2  - Tehnika
T1  - Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles
T1  - Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida
EP  - 433
IS  - 4
SP  - 429
VL  - 75
DO  - 10.5937/tehnika2004429V
ER  - 

@article{
author = "Vuksanović, Marija M. and Tomić, Nataša and Mladenović, Ivana and Perić, Tamara and Gligorijević, Bojan and Jančić-Heinemann, Radmila",
year = "2020",
abstract = "Composite materials based on acrylate UV-cured polymers (Bis-GMA/TEGDMA) as a matrix and reinforcements that can be selected in order to adjust the properties of the obtained composite are used in the field of dental technology. The role of reinforcement is to adjust the mechanical properties, but also to control the shrinkage during curing. As reinforcement, alumina particles doped with iron oxide (Al2O3 Fe) synthesized using the sol-gel technique were selected. In order to simulate the process of adhesive application in real conditions, in vitro testing technique and adhesion properties of synthesized adhesive were used, where tooth tissue was used as a substrate. Comparison with standard adhesives used in dentistry was used to compare adhesion. The quality of the adhesive joint was evaluated using the microhardness testing method using different loads where it is estimated how the adhesive makes a connection with the substrate. It was shown that the synthesized adhesive showed significantly enhanced adhesion compared to the standard adhesive used in dentistry (836%)., Kompozitni materijali na bazi akrilatnih fotopolimerizujućih polimera, (Bis-GMA/TEGDMA) koji predstavljaju matricu i ojačanja koja se mogu odabrati sa ciljem podešavanja svojstava dobijenih kompozita, koriste se u oblasti dentalne tehnologije. Uloga ojačanja je podešavanje mehaničkih svojstava, ali i kontrola skupljanja tokom očvršćavanja. Kao ojačanje odabrane su čestice aluminijum-oksida dopirane gvožđe oksidom (Al2O3 Fe), sintetisane korišćenjem sol-gel tehnike. U cilju simuliranja procesa primene adheziva u realnim uslovima korišćena je in vitro tehnika ispitivanja adhezije sintetisanog adheziva pri čemu je kao substrat korišćeno tkivo zuba. Dobijene vrednosti adhezije poređene su sa komercijalnim adhezivima koji se koriste u stomatologiji. Kvalitet adhezivnog spoja ocenjen je merenjem mikrotvrdoće primenom različitih opterećenja, pri čemu je procenjen način kako se ostvaruje spoj između filma i podloge. Pokazalo se da je sintetisani adheziv imao višestruko jaču adheziju u poređenju sa standardnim adhezivom korišćenim u stomatologiji (836 %).",
publisher = "Savez inženjera i tehničara Srbije, Beograd",
journal = "Tehnika",
title = "Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles, Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida",
pages = "433-429",
number = "4",
volume = "75",
doi = "10.5937/tehnika2004429V"
}

Vuksanović, M. M., Tomić, N., Mladenović, I., Perić, T., Gligorijević, B.,& Jančić-Heinemann, R.. (2020). Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles. in Tehnika
Savez inženjera i tehničara Srbije, Beograd., 75(4), 429-433.
https://doi.org/10.5937/tehnika2004429V

Vuksanović MM, Tomić N, Mladenović I, Perić T, Gligorijević B, Jančić-Heinemann R. Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles. in Tehnika. 2020;75(4):429-433.
doi:10.5937/tehnika2004429V .

Vuksanović, Marija M., Tomić, Nataša, Mladenović, Ivana, Perić, Tamara, Gligorijević, Bojan, Jančić-Heinemann, Radmila, "Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles" in Tehnika, 75, no. 4 (2020):429-433,
https://doi.org/10.5937/tehnika2004429V . .

TY  - JOUR
AU  - Radetić, Tamara
AU  - Popović, Miljana
AU  - Gligorijević, Bojan
AU  - Alil, Ana
AU  - Romhanji, Endre
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4047
AB  - The occurrence of abnormal grain growth (AGG) in AA5182 alloy during annealing imposes severe restrictions on processing parameters and deteriorates mechanical properties. In this work, we investigated the effect of chemical composition on the appearance of abnormal grain growth by varying Mg and Mn content in the range of composition limits for standard AA5182 alloy, 4.0-5.0% Mg, and 0.2-0.5% Mn, respectively. Thermo-mechanical processing of alloys included cold rolling with reductions ranging from 40 to 85%, followed by annealing in the temperature range from 350 to 520 degrees C. The results showed that the rise in alloying elements content drives the onset of abnormal grain growth toward higher temperatures. The increase in the cold rolling reduction degree promotes abnormal grain growth and lowers its onset temperature. Abnormal grain growth and grain boundary mobility showed strong anisotropy related to rod-like shape and alignment of Al6Mn(Fe) dispersoids through Zener pinning.
PB  - Savez inženjera metalurgije Srbije, Beograd
T2  - Metallurgical & Materials Engineering
T1  - The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys
EP  - 323
IS  - 4
SP  - 315
VL  - 25
DO  - 10.30544/463
ER  - 

@article{
author = "Radetić, Tamara and Popović, Miljana and Gligorijević, Bojan and Alil, Ana and Romhanji, Endre",
year = "2019",
abstract = "The occurrence of abnormal grain growth (AGG) in AA5182 alloy during annealing imposes severe restrictions on processing parameters and deteriorates mechanical properties. In this work, we investigated the effect of chemical composition on the appearance of abnormal grain growth by varying Mg and Mn content in the range of composition limits for standard AA5182 alloy, 4.0-5.0% Mg, and 0.2-0.5% Mn, respectively. Thermo-mechanical processing of alloys included cold rolling with reductions ranging from 40 to 85%, followed by annealing in the temperature range from 350 to 520 degrees C. The results showed that the rise in alloying elements content drives the onset of abnormal grain growth toward higher temperatures. The increase in the cold rolling reduction degree promotes abnormal grain growth and lowers its onset temperature. Abnormal grain growth and grain boundary mobility showed strong anisotropy related to rod-like shape and alignment of Al6Mn(Fe) dispersoids through Zener pinning.",
publisher = "Savez inženjera metalurgije Srbije, Beograd",
journal = "Metallurgical & Materials Engineering",
title = "The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys",
pages = "323-315",
number = "4",
volume = "25",
doi = "10.30544/463"
}

Radetić, T., Popović, M., Gligorijević, B., Alil, A.,& Romhanji, E.. (2019). The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys. in Metallurgical & Materials Engineering
Savez inženjera metalurgije Srbije, Beograd., 25(4), 315-323.
https://doi.org/10.30544/463

Radetić T, Popović M, Gligorijević B, Alil A, Romhanji E. The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys. in Metallurgical & Materials Engineering. 2019;25(4):315-323.
doi:10.30544/463 .

Radetić, Tamara, Popović, Miljana, Gligorijević, Bojan, Alil, Ana, Romhanji, Endre, "The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys" in Metallurgical & Materials Engineering, 25, no. 4 (2019):315-323,
https://doi.org/10.30544/463 . .

TY  - CONF
AU  - Radetić, Tamara
AU  - Gligorijević, Bojan
AU  - Filipović, Mirjana
AU  - Popović, Miljana
AU  - Romhanji, Endre
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/7297
AB  - The subject of this study has been an investigation of the homogenization temperature 
effect on the microstructure of Al-Mg-Si alloy containing low-melting point Pb and Bi 
elements. The results of the characterization show that homogenization at temperatures 
lower than 500 °C requires extraordinary long in order to initiate ß-AlFeSi -> α-AlFe(Mn)Si 
transformation, necessary for good extrdability of the alloy ransformation, necessary for 
good extrudability of the alloy. In addition, precipitation of ß-Mg2Si phase takes place, 
decreasing the alloy's aging potential during the further processing. High-temperature 
homogenization not only results in complete ß-AlFeSi -> α-AlFe(Mn)Si transformation and 
dissolution of ß-Mg2Si phase but expected Pb and Bi escape to the specimen surface does 
not occur.
AB  - Predmet ovog rada je bilo ispitivanje i karakterizacija uslova homogenizacionog žarenja na 
mikrostruktu Al-Mg-Si legure legirane nisko-topivim metalima Pb i Bi. Rezultati pokazuju da 
homogenizacija na temperaturama nižim od 500 °C zahteva izuzetno duga vremena žarenja 
da bi došlo do ß-AlFeSi -> α-AlFe(Mn)Si transformacije, neophodne za sposobnost legure za 
presovanje. Dodatno, dolazi do izdvajanja ß-Mg2Si faze, čime se smanjuje sposobnost legure 
za starenje u daljoj preradi. Visoko-temperaturna homogenizacija ne samo da rezultuje u 
potpunoj ß-AlFeSi -> α-AlFe(Mn)Si transformaciji i rastvaranju ß-Mg2Si faze, već i ne dolazi 
do očekivanog gubitka Pb i Bi usled izdvajanja na površini uzoraka.
PB  - Beograd : Serbian Chemical Society
C3  - Proceedings / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018
T1  - Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements
T1  - Efekat homogenizacije na mikrostrukturu Al-Mg-Si legure koja sadrži nisko-topive elemente
EP  - 94
SP  - 89
UR  - https://hdl.handle.net/21.15107/rcub_technorep_7297
ER  - 

@conference{
author = "Radetić, Tamara and Gligorijević, Bojan and Filipović, Mirjana and Popović, Miljana and Romhanji, Endre",
year = "2018",
abstract = "The subject of this study has been an investigation of the homogenization temperature 
effect on the microstructure of Al-Mg-Si alloy containing low-melting point Pb and Bi 
elements. The results of the characterization show that homogenization at temperatures 
lower than 500 °C requires extraordinary long in order to initiate ß-AlFeSi -> α-AlFe(Mn)Si 
transformation, necessary for good extrdability of the alloy ransformation, necessary for 
good extrudability of the alloy. In addition, precipitation of ß-Mg2Si phase takes place, 
decreasing the alloy's aging potential during the further processing. High-temperature 
homogenization not only results in complete ß-AlFeSi -> α-AlFe(Mn)Si transformation and 
dissolution of ß-Mg2Si phase but expected Pb and Bi escape to the specimen surface does 
not occur., Predmet ovog rada je bilo ispitivanje i karakterizacija uslova homogenizacionog žarenja na 
mikrostruktu Al-Mg-Si legure legirane nisko-topivim metalima Pb i Bi. Rezultati pokazuju da 
homogenizacija na temperaturama nižim od 500 °C zahteva izuzetno duga vremena žarenja 
da bi došlo do ß-AlFeSi -> α-AlFe(Mn)Si transformacije, neophodne za sposobnost legure za 
presovanje. Dodatno, dolazi do izdvajanja ß-Mg2Si faze, čime se smanjuje sposobnost legure 
za starenje u daljoj preradi. Visoko-temperaturna homogenizacija ne samo da rezultuje u 
potpunoj ß-AlFeSi -> α-AlFe(Mn)Si transformaciji i rastvaranju ß-Mg2Si faze, već i ne dolazi 
do očekivanog gubitka Pb i Bi usled izdvajanja na površini uzoraka.",
publisher = "Beograd : Serbian Chemical Society",
journal = "Proceedings / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018",
title = "Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements, Efekat homogenizacije na mikrostrukturu Al-Mg-Si legure koja sadrži nisko-topive elemente",
pages = "94-89",
url = "https://hdl.handle.net/21.15107/rcub_technorep_7297"
}

Radetić, T., Gligorijević, B., Filipović, M., Popović, M.,& Romhanji, E.. (2018). Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements. in Proceedings / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018
Beograd : Serbian Chemical Society., 89-94.
https://hdl.handle.net/21.15107/rcub_technorep_7297

Radetić T, Gligorijević B, Filipović M, Popović M, Romhanji E. Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements. in Proceedings / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018. 2018;:89-94.
https://hdl.handle.net/21.15107/rcub_technorep_7297 .

Radetić, Tamara, Gligorijević, Bojan, Filipović, Mirjana, Popović, Miljana, Romhanji, Endre, "Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements" in Proceedings / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018 (2018):89-94,
https://hdl.handle.net/21.15107/rcub_technorep_7297 .

TY  - CONF
AU  - Radetić, Tamara
AU  - Gligorijević, Bojan
AU  - Filipović, Mirjana
AU  - Popović, Miljana
AU  - Romhanji, Endre
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/7298
AB  - The subject of this study has been an investigation of the homogenization temperature 
effect on the microstructure of Al-Mg-Si alloy containing low-melting point Pb and Bi 
elements. The results of the characterization show that homogenization at temperatures 
lower than 500 °C requires extraordinary long in order to initiate ß-AlFeSi -> α-AlFe(Mn)Si 
transformation, necessary for good extrdability of the alloy ransformation, necessary for 
good extrudability of the alloy. In addition, precipitation of ß-Mg2Si phase takes place, 
decreasing the alloy's aging potential during the further processing. High-temperature 
homogenization not only results in complete ß-AlFeSi -> α-AlFe(Mn)Si transformation and 
dissolution of ß-Mg2Si phase but expected Pb and Bi escape to the specimen surface does 
not occur.
AB  - Predmet ovog rada je bilo ispitivanje i karakterizacija uslova homogenizacionog žarenja na 
mikrostruktu Al-Mg-Si legure legirane nisko-topivim metalima Pb i Bi. Rezultati pokazuju da 
homogenizacija na temperaturama nižim od 500 °C zahteva izuzetno duga vremena žarenja 
da bi došlo do ß-AlFeSi -> α-AlFe(Mn)Si transformacije, neophodne za sposobnost legure za 
presovanje. Dodatno, dolazi do izdvajanja ß-Mg2Si faze, čime se smanjuje sposobnost legure 
za starenje u daljoj preradi. Visoko-temperaturna homogenizacija ne samo da rezultuje u 
potpunoj ß-AlFeSi -> α-AlFe(Mn)Si transformaciji i rastvaranju ß-Mg2Si faze, već i ne dolazi 
do očekivanog gubitka Pb i Bi usled izdvajanja na površini uzoraka.
PB  - Beograd : Serbian Chemical Society
C3  - Book of Abstracts / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018
T1  - Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements
T1  - Effekat homogenizacije na mikrostrukturu Al-Mg-Si legure koja sadrži niskotopive elemente
SP  - 37
UR  - https://hdl.handle.net/21.15107/rcub_technorep_7298
ER  - 

@conference{
author = "Radetić, Tamara and Gligorijević, Bojan and Filipović, Mirjana and Popović, Miljana and Romhanji, Endre",
year = "2018",
abstract = "The subject of this study has been an investigation of the homogenization temperature 
effect on the microstructure of Al-Mg-Si alloy containing low-melting point Pb and Bi 
elements. The results of the characterization show that homogenization at temperatures 
lower than 500 °C requires extraordinary long in order to initiate ß-AlFeSi -> α-AlFe(Mn)Si 
transformation, necessary for good extrdability of the alloy ransformation, necessary for 
good extrudability of the alloy. In addition, precipitation of ß-Mg2Si phase takes place, 
decreasing the alloy's aging potential during the further processing. High-temperature 
homogenization not only results in complete ß-AlFeSi -> α-AlFe(Mn)Si transformation and 
dissolution of ß-Mg2Si phase but expected Pb and Bi escape to the specimen surface does 
not occur., Predmet ovog rada je bilo ispitivanje i karakterizacija uslova homogenizacionog žarenja na 
mikrostruktu Al-Mg-Si legure legirane nisko-topivim metalima Pb i Bi. Rezultati pokazuju da 
homogenizacija na temperaturama nižim od 500 °C zahteva izuzetno duga vremena žarenja 
da bi došlo do ß-AlFeSi -> α-AlFe(Mn)Si transformacije, neophodne za sposobnost legure za 
presovanje. Dodatno, dolazi do izdvajanja ß-Mg2Si faze, čime se smanjuje sposobnost legure 
za starenje u daljoj preradi. Visoko-temperaturna homogenizacija ne samo da rezultuje u 
potpunoj ß-AlFeSi -> α-AlFe(Mn)Si transformaciji i rastvaranju ß-Mg2Si faze, već i ne dolazi 
do očekivanog gubitka Pb i Bi usled izdvajanja na površini uzoraka.",
publisher = "Beograd : Serbian Chemical Society",
journal = "Book of Abstracts / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018",
title = "Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements, Effekat homogenizacije na mikrostrukturu Al-Mg-Si legure koja sadrži niskotopive elemente",
pages = "37",
url = "https://hdl.handle.net/21.15107/rcub_technorep_7298"
}

Radetić, T., Gligorijević, B., Filipović, M., Popović, M.,& Romhanji, E.. (2018). Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements. in Book of Abstracts / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018
Beograd : Serbian Chemical Society., 37.
https://hdl.handle.net/21.15107/rcub_technorep_7298

Radetić T, Gligorijević B, Filipović M, Popović M, Romhanji E. Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements. in Book of Abstracts / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018. 2018;:37.
https://hdl.handle.net/21.15107/rcub_technorep_7298 .

Radetić, Tamara, Gligorijević, Bojan, Filipović, Mirjana, Popović, Miljana, Romhanji, Endre, "Homogenization effect on microstructure Al-Mg-Si alloy containing low-melting point elements" in Book of Abstracts / 55th meeting of the Serbian chemical society, Novi Sad, Serbia, June 8-9, 2018 (2018):37,
https://hdl.handle.net/21.15107/rcub_technorep_7298 .

TY  - JOUR
AU  - Gligorijević, Bojan
AU  - Vilotijević, Miroljub N.
AU  - Scepanović, Maja
AU  - Radovanović, Radovan V.
AU  - Radović, Nenad
PY  - 2017
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3562
AB  - The present study estimated the cracking phenomenon in as-plasma-sprayed hydroxylapatite coatings (HACs) after they were being subjected to the severe cutting conditions in the direction perpendicular to the coating/substrate interface. In order to evaluate the effects of substrate preheating on the occurrence of micro-cracks, the HACs were deposited at different initial substrate temperatures (T-S = 20, 100 and 200 degrees C). The changes in phase composition and HA splat morphology with T-S were observed and were correlated with the cracking occurrence. The results showed that severe cutting conditions introduced a localized cracking in the regions of HACs dominantly attributed to the brittle hydroxyl- deficient amorphous calcium phosphate (ACP) phase. This effect was particularly observable in the HACs deposited without preheating of substrate. On the other hand, the preheating of substrate reduced the presence of micro-cracks and caused insignificant changes in the average local phase composition. In HACs deposited with preheating of substrate, the HA splats (of which HACs are composed) were thinner and recrystallized HA regions seemed smaller in size and more evenly distributed. These results implied potentially important roles of the HA splat formation mechanism on the distribution of ACP and recrystallized HA regions in the as-plasma-sprayed HACs and the cracking resistance of HACs.
PB  - Savez hemijskih inženjera, Beograd
T2  - Hemijska industrija
T1  - Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures
EP  - 249
IS  - 3
SP  - 241
VL  - 71
DO  - 10.2298/HEMIND160513034G
ER  - 

@article{
author = "Gligorijević, Bojan and Vilotijević, Miroljub N. and Scepanović, Maja and Radovanović, Radovan V. and Radović, Nenad",
year = "2017",
abstract = "The present study estimated the cracking phenomenon in as-plasma-sprayed hydroxylapatite coatings (HACs) after they were being subjected to the severe cutting conditions in the direction perpendicular to the coating/substrate interface. In order to evaluate the effects of substrate preheating on the occurrence of micro-cracks, the HACs were deposited at different initial substrate temperatures (T-S = 20, 100 and 200 degrees C). The changes in phase composition and HA splat morphology with T-S were observed and were correlated with the cracking occurrence. The results showed that severe cutting conditions introduced a localized cracking in the regions of HACs dominantly attributed to the brittle hydroxyl- deficient amorphous calcium phosphate (ACP) phase. This effect was particularly observable in the HACs deposited without preheating of substrate. On the other hand, the preheating of substrate reduced the presence of micro-cracks and caused insignificant changes in the average local phase composition. In HACs deposited with preheating of substrate, the HA splats (of which HACs are composed) were thinner and recrystallized HA regions seemed smaller in size and more evenly distributed. These results implied potentially important roles of the HA splat formation mechanism on the distribution of ACP and recrystallized HA regions in the as-plasma-sprayed HACs and the cracking resistance of HACs.",
publisher = "Savez hemijskih inženjera, Beograd",
journal = "Hemijska industrija",
title = "Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures",
pages = "249-241",
number = "3",
volume = "71",
doi = "10.2298/HEMIND160513034G"
}

Gligorijević, B., Vilotijević, M. N., Scepanović, M., Radovanović, R. V.,& Radović, N.. (2017). Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures. in Hemijska industrija
Savez hemijskih inženjera, Beograd., 71(3), 241-249.
https://doi.org/10.2298/HEMIND160513034G

Gligorijević B, Vilotijević MN, Scepanović M, Radovanović RV, Radović N. Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures. in Hemijska industrija. 2017;71(3):241-249.
doi:10.2298/HEMIND160513034G .

Gligorijević, Bojan, Vilotijević, Miroljub N., Scepanović, Maja, Radovanović, Radovan V., Radović, Nenad, "Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures" in Hemijska industrija, 71, no. 3 (2017):241-249,
https://doi.org/10.2298/HEMIND160513034G . .

TY  - THES
AU  - Gligorijević, Bojan
PY  - 2016
UR  - http://eteze.bg.ac.rs/application/showtheses?thesesId=4616
UR  - https://fedorabg.bg.ac.rs/fedora/get/o:14750/bdef:Content/download
UR  - http://vbs.rs/scripts/cobiss?command=DISPLAY&base=70036&RID=48675343
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4652
AB  - In the present work, hydroxyapatite coatings (HACs) were deposited by using the high power laminar plasma spray process. Major objectives were: (i) to estimate effects of several deposition parameters on chemical, structural, and morphological properties of HACs and (ii) to evaluate effects of human proteins albumin and gamma globulin on the early stage of the biomineralization process on the surface of HACs in modified Kokubo solutions (simulated body fluids) in which the pH value was actively regulated using CO2.
AB  - U ovom radu je izvršeno nanošenje hidroksiapatitnih (HA) prevlaka primenom visokoenergetskog laminarnog plazma sprej postupka. Glavni ciljevi rada su bili: (i) da se ispita uticaj nekoliko parametara procesa nanošenja na hemijska, strukturna i morfološka svojstva HA prevlaka i (ii) da se ispita uticaj ljudskih proteina albumin i gama globulin na početni stadijum procesa biomineralizacije koji se javlja na površini dobijenih HA prevlaka u modifikovanim Kokubo rastvorima (simulirane telesne tečnosti) u kojima je vrednost pH bila aktivno regulisana pomoću CO2...
PB  - Univerzitet u Beogradu, Tehnološko-metalurški fakultet
T1  - Chemico-structural properties and biomineralization of hydroxyapatite coatings produced by high power laminar plasma spray process.
T1  - Hemijsko-strukturna svojstva i biomineralizacija hidroksiapatitnih prevlaka dobijenih visokoenergetskim laminarnim plazma sper postupkom
UR  - https://hdl.handle.net/21.15107/rcub_technorep_4652
ER  - 

@phdthesis{
author = "Gligorijević, Bojan",
year = "2016",
abstract = "In the present work, hydroxyapatite coatings (HACs) were deposited by using the high power laminar plasma spray process. Major objectives were: (i) to estimate effects of several deposition parameters on chemical, structural, and morphological properties of HACs and (ii) to evaluate effects of human proteins albumin and gamma globulin on the early stage of the biomineralization process on the surface of HACs in modified Kokubo solutions (simulated body fluids) in which the pH value was actively regulated using CO2., U ovom radu je izvršeno nanošenje hidroksiapatitnih (HA) prevlaka primenom visokoenergetskog laminarnog plazma sprej postupka. Glavni ciljevi rada su bili: (i) da se ispita uticaj nekoliko parametara procesa nanošenja na hemijska, strukturna i morfološka svojstva HA prevlaka i (ii) da se ispita uticaj ljudskih proteina albumin i gama globulin na početni stadijum procesa biomineralizacije koji se javlja na površini dobijenih HA prevlaka u modifikovanim Kokubo rastvorima (simulirane telesne tečnosti) u kojima je vrednost pH bila aktivno regulisana pomoću CO2...",
publisher = "Univerzitet u Beogradu, Tehnološko-metalurški fakultet",
title = "Chemico-structural properties and biomineralization of hydroxyapatite coatings produced by high power laminar plasma spray process., Hemijsko-strukturna svojstva i biomineralizacija hidroksiapatitnih prevlaka dobijenih visokoenergetskim laminarnim plazma sper postupkom",
url = "https://hdl.handle.net/21.15107/rcub_technorep_4652"
}

Gligorijević, B.. (2016). Chemico-structural properties and biomineralization of hydroxyapatite coatings produced by high power laminar plasma spray process.. 
Univerzitet u Beogradu, Tehnološko-metalurški fakultet..
https://hdl.handle.net/21.15107/rcub_technorep_4652

Gligorijević B. Chemico-structural properties and biomineralization of hydroxyapatite coatings produced by high power laminar plasma spray process.. 2016;.
https://hdl.handle.net/21.15107/rcub_technorep_4652 .

Gligorijević, Bojan, "Chemico-structural properties and biomineralization of hydroxyapatite coatings produced by high power laminar plasma spray process." (2016),
https://hdl.handle.net/21.15107/rcub_technorep_4652 .

TY  - JOUR
AU  - Bobić, Biljana
AU  - Jegdić, Bore
AU  - Jugović, Branimir
AU  - Stevanović, Jasmina
AU  - Gligorijević, Bojan
AU  - Murariu, Alin
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3171
AB  - Causes of failure of brass condenser tubes (CuZn28Sn1) in a thermal power plant in Serbia are analysed. Results of testing by Fourier transformed infrared spectroscopy (FTIR) have indicated the presence of ammonia and nitrogen compounds on fracture surfaces and on the inner surface of the tubes. These compounds are specific agents that cause stress corrosion cracking (SCC) in brass. Analysis of fracture surfaces using scanning electron microscopy (SEM) has shown the brittle transgranular fracture due to the occurrence of SCC. The resistance of brass condenser tubes to other types of corrosion, such as erosion, general and selective corrosion (dezincification) is also considered. Some procedures are proposed to reduce the risk of SCC in the brass condenser tubes.
PB  - Society for Structural Integrity and Life, Institute for Material Testing
T2  - Structural Integrity and Life
T1  - Failures of brass condenser tubes
EP  - 23
IS  - 1
SP  - 19
VL  - 16
UR  - https://hdl.handle.net/21.15107/rcub_technorep_3171
ER  - 

@article{
author = "Bobić, Biljana and Jegdić, Bore and Jugović, Branimir and Stevanović, Jasmina and Gligorijević, Bojan and Murariu, Alin",
year = "2016",
abstract = "Causes of failure of brass condenser tubes (CuZn28Sn1) in a thermal power plant in Serbia are analysed. Results of testing by Fourier transformed infrared spectroscopy (FTIR) have indicated the presence of ammonia and nitrogen compounds on fracture surfaces and on the inner surface of the tubes. These compounds are specific agents that cause stress corrosion cracking (SCC) in brass. Analysis of fracture surfaces using scanning electron microscopy (SEM) has shown the brittle transgranular fracture due to the occurrence of SCC. The resistance of brass condenser tubes to other types of corrosion, such as erosion, general and selective corrosion (dezincification) is also considered. Some procedures are proposed to reduce the risk of SCC in the brass condenser tubes.",
publisher = "Society for Structural Integrity and Life, Institute for Material Testing",
journal = "Structural Integrity and Life",
title = "Failures of brass condenser tubes",
pages = "23-19",
number = "1",
volume = "16",
url = "https://hdl.handle.net/21.15107/rcub_technorep_3171"
}

Bobić, B., Jegdić, B., Jugović, B., Stevanović, J., Gligorijević, B.,& Murariu, A.. (2016). Failures of brass condenser tubes. in Structural Integrity and Life
Society for Structural Integrity and Life, Institute for Material Testing., 16(1), 19-23.
https://hdl.handle.net/21.15107/rcub_technorep_3171

Bobić B, Jegdić B, Jugović B, Stevanović J, Gligorijević B, Murariu A. Failures of brass condenser tubes. in Structural Integrity and Life. 2016;16(1):19-23.
https://hdl.handle.net/21.15107/rcub_technorep_3171 .

Bobić, Biljana, Jegdić, Bore, Jugović, Branimir, Stevanović, Jasmina, Gligorijević, Bojan, Murariu, Alin, "Failures of brass condenser tubes" in Structural Integrity and Life, 16, no. 1 (2016):19-23,
https://hdl.handle.net/21.15107/rcub_technorep_3171 .

TY  - JOUR
AU  - Bobić, Biljana
AU  - Jegdić, Bore
AU  - Jugović, Branimir
AU  - Stevanović, Jasmina
AU  - Gligorijević, Bojan
AU  - Murariu, Alin
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3180
AB  - Causes of failure of brass condenser tubes (CuZn28Sn1) in a thermal power plant in Serbia are analysed. Results of testing by Fourier transformed infrared spectroscopy (FTIR) have indicated the presence of ammonia and nitro- gen compounds on fracture surfaces and on the inner surface of the tubes. These compounds are specific agents that cause stress corrosion cracking (SCC) in brass. Analy- sis of fracture surfaces using scanning electron microscopy (SEM) has shown the brittle transgranular fracture due to the occurrence of SCC. The resistance of brass condenser tubes to other types of corrosion, such as erosion, general and selective corrosion (dezincification) is also considered. Some procedures are proposed to reduce the risk of SCC in the brass condenser tubes.
AB  - Analizirani su uzroci pojave loma kondenzatorskih cevi od mesinga CuZn28Sn1 u jednoj termoelektrani u Srbiji. Rezultati ispitivanja metodom Furijeove transformisane infracrvene spektroskopije (FTIR) ukazuju na prisustvo amonijačnih i azotnih jedinjenja na površini loma i na unutrašnjoj površini cevi. Ta jedinjenja su specifični agensi za pojavu naponske korozije mesinga. Analiza površine loma primenom skening elektronske mikroskopije (SEM) pokazala je prisustvo krtog transkistalnog loma nastalog usled pojave naponske korozije. Razmatrana je otpornost cevi od mesinga CuZn28Sn1 prema drugim vidovima koro- zije, kao što su eroziona, opšta i selektivna korozija (decin- kacija). Predloženi su postupci za smanjenje rizika od pojave naponske korozije u kondenzatorskim cevima.
PB  - Institut za ispitivanje materijala, Beograd
T2  - Structural Integrity and Life
T1  - Failures of Brass Condenser Tubes
T1  - Lomovi kondenzatorskih cevi od mesinga
EP  - 23
IS  - 1
SP  - 19
VL  - 16
UR  - https://hdl.handle.net/21.15107/rcub_technorep_3180
ER  - 

@article{
author = "Bobić, Biljana and Jegdić, Bore and Jugović, Branimir and Stevanović, Jasmina and Gligorijević, Bojan and Murariu, Alin",
year = "2016",
abstract = "Causes of failure of brass condenser tubes (CuZn28Sn1) in a thermal power plant in Serbia are analysed. Results of testing by Fourier transformed infrared spectroscopy (FTIR) have indicated the presence of ammonia and nitro- gen compounds on fracture surfaces and on the inner surface of the tubes. These compounds are specific agents that cause stress corrosion cracking (SCC) in brass. Analy- sis of fracture surfaces using scanning electron microscopy (SEM) has shown the brittle transgranular fracture due to the occurrence of SCC. The resistance of brass condenser tubes to other types of corrosion, such as erosion, general and selective corrosion (dezincification) is also considered. Some procedures are proposed to reduce the risk of SCC in the brass condenser tubes., Analizirani su uzroci pojave loma kondenzatorskih cevi od mesinga CuZn28Sn1 u jednoj termoelektrani u Srbiji. Rezultati ispitivanja metodom Furijeove transformisane infracrvene spektroskopije (FTIR) ukazuju na prisustvo amonijačnih i azotnih jedinjenja na površini loma i na unutrašnjoj površini cevi. Ta jedinjenja su specifični agensi za pojavu naponske korozije mesinga. Analiza površine loma primenom skening elektronske mikroskopije (SEM) pokazala je prisustvo krtog transkistalnog loma nastalog usled pojave naponske korozije. Razmatrana je otpornost cevi od mesinga CuZn28Sn1 prema drugim vidovima koro- zije, kao što su eroziona, opšta i selektivna korozija (decin- kacija). Predloženi su postupci za smanjenje rizika od pojave naponske korozije u kondenzatorskim cevima.",
publisher = "Institut za ispitivanje materijala, Beograd",
journal = "Structural Integrity and Life",
title = "Failures of Brass Condenser Tubes, Lomovi kondenzatorskih cevi od mesinga",
pages = "23-19",
number = "1",
volume = "16",
url = "https://hdl.handle.net/21.15107/rcub_technorep_3180"
}

Bobić, B., Jegdić, B., Jugović, B., Stevanović, J., Gligorijević, B.,& Murariu, A.. (2016). Failures of Brass Condenser Tubes. in Structural Integrity and Life
Institut za ispitivanje materijala, Beograd., 16(1), 19-23.
https://hdl.handle.net/21.15107/rcub_technorep_3180

Bobić B, Jegdić B, Jugović B, Stevanović J, Gligorijević B, Murariu A. Failures of Brass Condenser Tubes. in Structural Integrity and Life. 2016;16(1):19-23.
https://hdl.handle.net/21.15107/rcub_technorep_3180 .

Bobić, Biljana, Jegdić, Bore, Jugović, Branimir, Stevanović, Jasmina, Gligorijević, Bojan, Murariu, Alin, "Failures of Brass Condenser Tubes" in Structural Integrity and Life, 16, no. 1 (2016):19-23,
https://hdl.handle.net/21.15107/rcub_technorep_3180 .

TY  - JOUR
AU  - Gligorijević, Bojan
AU  - Vilotijević, Miroljub N.
AU  - Scepanović, Maja
AU  - Vidović, Dragoslav
AU  - Radović, Nenad
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3338
AB  - The aim of this work was to examine the dependence of the local surface structure (surface structural heterogeneity) on the local thickness (thickness uniformity) and structure properties along the thickness of hydroxyapatite coatings (HACs) deposited by using the high power (52 kW) laminar plasma jet. For the deposition process, a relatively small size of the feedstock hydroxyapatite powder (HAP) (33 mu m) was used. The HACs were deposited at different stand-off distances (SODs) (80, 100, and 150 mm) without preheating of substrates. The thickness measurements were performed by using the calibrated micrometer and light microscopy (LM). The surface micro-structure was analyzed by using the micro-Raman spectroscopy (MRS), whereas the micro-structure along the thickness of HACs was studied by using the MRS, X-ray powder diffractometry (XRPD), and LM (combined with chemical etching). The results showed a heterogeneous phase distribution on the surface of each HAC analyzed as well as the non-uniform thickness of HACs. Apparently, a correlation existed between the local surface structure and the local thickness of HACs. However, the MRS, XRPD, and LM analyses of micro-structure along the thickness of HACs indicated that the differences in the local surface structure could be related to the different recrystallization established during the plasma deposition process in the different parts along the thickness of each HAC analyzed.
PB  - Elsevier Science Sa, Lausanne
T2  - Journal of Alloys and Compounds
T1  - Surface structural heterogeneity of high power plasma-sprayed hydroxyapatite coatings
EP  - 430
SP  - 421
VL  - 687
DO  - 10.1016/j.jallcom.2016.06.163
ER  - 

@article{
author = "Gligorijević, Bojan and Vilotijević, Miroljub N. and Scepanović, Maja and Vidović, Dragoslav and Radović, Nenad",
year = "2016",
abstract = "The aim of this work was to examine the dependence of the local surface structure (surface structural heterogeneity) on the local thickness (thickness uniformity) and structure properties along the thickness of hydroxyapatite coatings (HACs) deposited by using the high power (52 kW) laminar plasma jet. For the deposition process, a relatively small size of the feedstock hydroxyapatite powder (HAP) (33 mu m) was used. The HACs were deposited at different stand-off distances (SODs) (80, 100, and 150 mm) without preheating of substrates. The thickness measurements were performed by using the calibrated micrometer and light microscopy (LM). The surface micro-structure was analyzed by using the micro-Raman spectroscopy (MRS), whereas the micro-structure along the thickness of HACs was studied by using the MRS, X-ray powder diffractometry (XRPD), and LM (combined with chemical etching). The results showed a heterogeneous phase distribution on the surface of each HAC analyzed as well as the non-uniform thickness of HACs. Apparently, a correlation existed between the local surface structure and the local thickness of HACs. However, the MRS, XRPD, and LM analyses of micro-structure along the thickness of HACs indicated that the differences in the local surface structure could be related to the different recrystallization established during the plasma deposition process in the different parts along the thickness of each HAC analyzed.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Journal of Alloys and Compounds",
title = "Surface structural heterogeneity of high power plasma-sprayed hydroxyapatite coatings",
pages = "430-421",
volume = "687",
doi = "10.1016/j.jallcom.2016.06.163"
}

Gligorijević, B., Vilotijević, M. N., Scepanović, M., Vidović, D.,& Radović, N.. (2016). Surface structural heterogeneity of high power plasma-sprayed hydroxyapatite coatings. in Journal of Alloys and Compounds
Elsevier Science Sa, Lausanne., 687, 421-430.
https://doi.org/10.1016/j.jallcom.2016.06.163

Gligorijević B, Vilotijević MN, Scepanović M, Vidović D, Radović N. Surface structural heterogeneity of high power plasma-sprayed hydroxyapatite coatings. in Journal of Alloys and Compounds. 2016;687:421-430.
doi:10.1016/j.jallcom.2016.06.163 .

Gligorijević, Bojan, Vilotijević, Miroljub N., Scepanović, Maja, Vidović, Dragoslav, Radović, Nenad, "Surface structural heterogeneity of high power plasma-sprayed hydroxyapatite coatings" in Journal of Alloys and Compounds, 687 (2016):421-430,
https://doi.org/10.1016/j.jallcom.2016.06.163 . .

TY  - JOUR
AU  - Milašinović, Veljko D.
AU  - Radovanović, Radovan V.
AU  - Milašinović, Mijat D.
AU  - Gligorijević, Bojan
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3369
AB  - The objective of this research is to consider the effects of certain parameters of the friction-welding process on the morphology of an aluminum/copper joint. The effect of the following parameters was monitored: the operating time, the operating pressure, the forging time and the forging pressure. The speed was constant during the binding process and reached 1500 min(-1). The preparation of the welding materials was performed in accordance with the industrial production conditions. With the SEM-EDS analysis, it was found that the morphology of the Al/Cu interface slightly changes when we change the distance from the rotation axis, irrespective of the combination of the friction-welding parameters. Apart from this, the joined effects of the operating pressure of 48 MPa and the forging pressure of 160 MPa caused a morphological change of the Al/Cu interface, while the forging time at the moment of the combined pressurizing effect significantly influenced the modification of the Al/Cu interface shape within a very narrow time interval of only a few seconds.
PB  - Inst Za Kovinske Materiale I In Tehnologie, Ljubjana
T2  - Materiali in Tehnologije
T1  - Effects of friction-welding parameters on the morphological properties of an al/cu bimetallic joint
EP  - 94
IS  - 1
SP  - 89
VL  - 50
DO  - 10.17222/mit.2014.304
ER  - 

@article{
author = "Milašinović, Veljko D. and Radovanović, Radovan V. and Milašinović, Mijat D. and Gligorijević, Bojan",
year = "2016",
abstract = "The objective of this research is to consider the effects of certain parameters of the friction-welding process on the morphology of an aluminum/copper joint. The effect of the following parameters was monitored: the operating time, the operating pressure, the forging time and the forging pressure. The speed was constant during the binding process and reached 1500 min(-1). The preparation of the welding materials was performed in accordance with the industrial production conditions. With the SEM-EDS analysis, it was found that the morphology of the Al/Cu interface slightly changes when we change the distance from the rotation axis, irrespective of the combination of the friction-welding parameters. Apart from this, the joined effects of the operating pressure of 48 MPa and the forging pressure of 160 MPa caused a morphological change of the Al/Cu interface, while the forging time at the moment of the combined pressurizing effect significantly influenced the modification of the Al/Cu interface shape within a very narrow time interval of only a few seconds.",
publisher = "Inst Za Kovinske Materiale I In Tehnologie, Ljubjana",
journal = "Materiali in Tehnologije",
title = "Effects of friction-welding parameters on the morphological properties of an al/cu bimetallic joint",
pages = "94-89",
number = "1",
volume = "50",
doi = "10.17222/mit.2014.304"
}

Milašinović, V. D., Radovanović, R. V., Milašinović, M. D.,& Gligorijević, B.. (2016). Effects of friction-welding parameters on the morphological properties of an al/cu bimetallic joint. in Materiali in Tehnologije
Inst Za Kovinske Materiale I In Tehnologie, Ljubjana., 50(1), 89-94.
https://doi.org/10.17222/mit.2014.304

Milašinović VD, Radovanović RV, Milašinović MD, Gligorijević B. Effects of friction-welding parameters on the morphological properties of an al/cu bimetallic joint. in Materiali in Tehnologije. 2016;50(1):89-94.
doi:10.17222/mit.2014.304 .

Milašinović, Veljko D., Radovanović, Radovan V., Milašinović, Mijat D., Gligorijević, Bojan, "Effects of friction-welding parameters on the morphological properties of an al/cu bimetallic joint" in Materiali in Tehnologije, 50, no. 1 (2016):89-94,
https://doi.org/10.17222/mit.2014.304 . .

TY  - JOUR
AU  - Gligorijević, Bojan
AU  - Vilotijević, Miroljub N.
AU  - Scepanović, Maja
AU  - Vuković, Nikola S.
AU  - Radović, Nenad
PY  - 2016
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3403
AB  - The aim of the present study was to investigate the influence of substrate preheating on the structural properties of hydroxyapatite coatings (HACs) deposited by using the high power (52 kW) laminar plasma jet. The deposition experiments were performed within the 20-200 degrees C temperature range at different stand-off distances. The structural properties in the thickness direction and at the surface of the HACs were investigated by using the micro-Raman spectroscopy, scanning electron microscopy coupled with energy dispersive spectrometry, and X-ray powder diffractometry. The deposition without the preheating of the substrate produced HACs with crystallinity gradient in the thickness direction. At the stand-off distance of 80 mm, the preheating of the substrate at 200 degrees C practically eliminated the crystallinity gradient. At distances from the coating/substrate interface shorter than similar to 100 mu m, the increase of crystallinity with the preheating of the substrate was dominantly attributed to the recrystallization of hydroxyl-rich ACP into HA. At longer distances and higher initial substrate temperatures (  gt  100 degrees C), the crystallinity changes were negligible, whereas the recrystallization of hydroxyl-deficient ACP into oxyapatite (OA) was also possible. The X-ray diffractometry indicated the deposition conditions under which a minimum residual stress was achieved. The results of the present study strongly suggested the relation between the ACP - gt  HA remystallization process and the bonding strength of the HACs.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Substrate preheating and structural properties of power plasma sprayed hydroxyapatite coatings
EP  - 420
IS  - 1
SP  - 411
VL  - 42
DO  - 10.1016/j.ceramint.2015.08.125
ER  - 

@article{
author = "Gligorijević, Bojan and Vilotijević, Miroljub N. and Scepanović, Maja and Vuković, Nikola S. and Radović, Nenad",
year = "2016",
abstract = "The aim of the present study was to investigate the influence of substrate preheating on the structural properties of hydroxyapatite coatings (HACs) deposited by using the high power (52 kW) laminar plasma jet. The deposition experiments were performed within the 20-200 degrees C temperature range at different stand-off distances. The structural properties in the thickness direction and at the surface of the HACs were investigated by using the micro-Raman spectroscopy, scanning electron microscopy coupled with energy dispersive spectrometry, and X-ray powder diffractometry. The deposition without the preheating of the substrate produced HACs with crystallinity gradient in the thickness direction. At the stand-off distance of 80 mm, the preheating of the substrate at 200 degrees C practically eliminated the crystallinity gradient. At distances from the coating/substrate interface shorter than similar to 100 mu m, the increase of crystallinity with the preheating of the substrate was dominantly attributed to the recrystallization of hydroxyl-rich ACP into HA. At longer distances and higher initial substrate temperatures (  gt  100 degrees C), the crystallinity changes were negligible, whereas the recrystallization of hydroxyl-deficient ACP into oxyapatite (OA) was also possible. The X-ray diffractometry indicated the deposition conditions under which a minimum residual stress was achieved. The results of the present study strongly suggested the relation between the ACP - gt  HA remystallization process and the bonding strength of the HACs.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Substrate preheating and structural properties of power plasma sprayed hydroxyapatite coatings",
pages = "420-411",
number = "1",
volume = "42",
doi = "10.1016/j.ceramint.2015.08.125"
}

Gligorijević, B., Vilotijević, M. N., Scepanović, M., Vuković, N. S.,& Radović, N.. (2016). Substrate preheating and structural properties of power plasma sprayed hydroxyapatite coatings. in Ceramics International
Elsevier Sci Ltd, Oxford., 42(1), 411-420.
https://doi.org/10.1016/j.ceramint.2015.08.125

Gligorijević B, Vilotijević MN, Scepanović M, Vuković NS, Radović N. Substrate preheating and structural properties of power plasma sprayed hydroxyapatite coatings. in Ceramics International. 2016;42(1):411-420.
doi:10.1016/j.ceramint.2015.08.125 .

Gligorijević, Bojan, Vilotijević, Miroljub N., Scepanović, Maja, Vuković, Nikola S., Radović, Nenad, "Substrate preheating and structural properties of power plasma sprayed hydroxyapatite coatings" in Ceramics International, 42, no. 1 (2016):411-420,
https://doi.org/10.1016/j.ceramint.2015.08.125 . .

TY  - JOUR
AU  - Vencl, Aleksandar A.
AU  - Katavić, B.
AU  - Marković, D.
AU  - Ristić, M.
AU  - Gligorijević, Bojan
PY  - 2015
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2889
AB  - During the coal pulverizing, the working parts of the ventilation mill are being worn by the sand particles. For this reason, the working parts are usually protected with materials resistant to wear (hardfaced/thermal sprayed coatings). The aim of this study was to evaluate the tribological performance of four different types of coatings as candidates for wear protection of the mill's working parts. The coatings were produced by using the filler materials with the following nominal chemical composition: NiFeBSi-WC, NiCrBSiC, FeCrCTiSi, and FeCrNiCSiBMn, and by using the plasma arc welding and flame and electric arc spraying processes. The results showed that Ni-based coatings exhibited higher wear resistance than Fe-based coatings. The highest wear resistance showed coating produced by using the NiFeBSi-WC filler material and plasma transferred arc welding deposition process. The hardness was not the only characteristic that affected the wear resistance. In this context, the wear rate of NiFeBSi-WC coating was not in correlation with its hardness, in contrast to other coatings. The different wear performance of NiFeBSi-WC coating was attributed to the different type and morphological features of the reinforcing particles (WC).
PB  - Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac
T2  - Tribology in Industry
T1  - The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts
EP  - 329
IS  - 3
SP  - 320
VL  - 37
UR  - https://hdl.handle.net/21.15107/rcub_technorep_2889
ER  - 

@article{
author = "Vencl, Aleksandar A. and Katavić, B. and Marković, D. and Ristić, M. and Gligorijević, Bojan",
year = "2015",
abstract = "During the coal pulverizing, the working parts of the ventilation mill are being worn by the sand particles. For this reason, the working parts are usually protected with materials resistant to wear (hardfaced/thermal sprayed coatings). The aim of this study was to evaluate the tribological performance of four different types of coatings as candidates for wear protection of the mill's working parts. The coatings were produced by using the filler materials with the following nominal chemical composition: NiFeBSi-WC, NiCrBSiC, FeCrCTiSi, and FeCrNiCSiBMn, and by using the plasma arc welding and flame and electric arc spraying processes. The results showed that Ni-based coatings exhibited higher wear resistance than Fe-based coatings. The highest wear resistance showed coating produced by using the NiFeBSi-WC filler material and plasma transferred arc welding deposition process. The hardness was not the only characteristic that affected the wear resistance. In this context, the wear rate of NiFeBSi-WC coating was not in correlation with its hardness, in contrast to other coatings. The different wear performance of NiFeBSi-WC coating was attributed to the different type and morphological features of the reinforcing particles (WC).",
publisher = "Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac",
journal = "Tribology in Industry",
title = "The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts",
pages = "329-320",
number = "3",
volume = "37",
url = "https://hdl.handle.net/21.15107/rcub_technorep_2889"
}

Vencl, A. A., Katavić, B., Marković, D., Ristić, M.,& Gligorijević, B.. (2015). The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts. in Tribology in Industry
Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac., 37(3), 320-329.
https://hdl.handle.net/21.15107/rcub_technorep_2889

Vencl AA, Katavić B, Marković D, Ristić M, Gligorijević B. The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts. in Tribology in Industry. 2015;37(3):320-329.
https://hdl.handle.net/21.15107/rcub_technorep_2889 .

Vencl, Aleksandar A., Katavić, B., Marković, D., Ristić, M., Gligorijević, Bojan, "The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts" in Tribology in Industry, 37, no. 3 (2015):320-329,
https://hdl.handle.net/21.15107/rcub_technorep_2889 .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Gligorijević, Bojan
AU  - Mišković-Stanković, Vesna
PY  - 2014
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2602
AB  - Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements in the 3.5 wt. % NaCl solution have shown a more positive value of the pitting potential (Epit) and a higher corrosion resistance for the two-step aged alloy. The electrochemical impedance spectroscopy (EIS) has also shown that the two-step aged alloy has better corrosion properties (higher value of polarization resistance, Rp, and lower value of double-layer capacitance, Cdl) comparing to the one-step aged alloy.
AB  - Otpornost prema koroziji aluminijumske legure serije 7000 ispitivana je primenom različitih elektrohemijskih metoda. Legura je bila podvrgnuta jednostepenom i novom dvostepenom termičkom taloženju. Polarizaciona merenja u 3,5 mas.% NaCl su pokazala da legura posle dvostepenog termičkog taloženja ima pozitivniju vrednost potencijala pitinga (Epit) i veću otpornost prema koroziji. Spektroskopija elektrohemijske impedancije (SEI) je takođe pokazala da legura posle dvostepenog termičkog taloženja ima bolju otpornost prema koroziji (veću vrednost polarizacione otpornosti, Rp i manju vrednost kapacitivnosti dvojnog sloja, Cdl) u poređenju sa legurom posle jednostepenog termičkog taloženja.
PB  - Engineering Society for Corrosion, Belgrade, Serbia
T2  - Zaštita materijala
T1  - Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening
T1  - Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
EP  - 394
IS  - 4
SP  - 387
VL  - 55
DO  - 10.5937/ZasMat1404387J
ER  - 

@article{
author = "Jegdić, Bore and Bobić, Biljana and Gligorijević, Bojan and Mišković-Stanković, Vesna",
year = "2014",
abstract = "Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements in the 3.5 wt. % NaCl solution have shown a more positive value of the pitting potential (Epit) and a higher corrosion resistance for the two-step aged alloy. The electrochemical impedance spectroscopy (EIS) has also shown that the two-step aged alloy has better corrosion properties (higher value of polarization resistance, Rp, and lower value of double-layer capacitance, Cdl) comparing to the one-step aged alloy., Otpornost prema koroziji aluminijumske legure serije 7000 ispitivana je primenom različitih elektrohemijskih metoda. Legura je bila podvrgnuta jednostepenom i novom dvostepenom termičkom taloženju. Polarizaciona merenja u 3,5 mas.% NaCl su pokazala da legura posle dvostepenog termičkog taloženja ima pozitivniju vrednost potencijala pitinga (Epit) i veću otpornost prema koroziji. Spektroskopija elektrohemijske impedancije (SEI) je takođe pokazala da legura posle dvostepenog termičkog taloženja ima bolju otpornost prema koroziji (veću vrednost polarizacione otpornosti, Rp i manju vrednost kapacitivnosti dvojnog sloja, Cdl) u poređenju sa legurom posle jednostepenog termičkog taloženja.",
publisher = "Engineering Society for Corrosion, Belgrade, Serbia",
journal = "Zaštita materijala",
title = "Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening, Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja",
pages = "394-387",
number = "4",
volume = "55",
doi = "10.5937/ZasMat1404387J"
}

Jegdić, B., Bobić, B., Gligorijević, B.,& Mišković-Stanković, V.. (2014). Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening. in Zaštita materijala
Engineering Society for Corrosion, Belgrade, Serbia., 55(4), 387-394.
https://doi.org/10.5937/ZasMat1404387J

Jegdić B, Bobić B, Gligorijević B, Mišković-Stanković V. Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening. in Zaštita materijala. 2014;55(4):387-394.
doi:10.5937/ZasMat1404387J .

Jegdić, Bore, Bobić, Biljana, Gligorijević, Bojan, Mišković-Stanković, Vesna, "Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening" in Zaštita materijala, 55, no. 4 (2014):387-394,
https://doi.org/10.5937/ZasMat1404387J . .

TY  - JOUR
AU  - Kutin, Marina
AU  - Prokolab, Milan
AU  - Ristić, Marko
AU  - Alil, Ana
AU  - Gligorijević, Bojan
PY  - 2013
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2452
AB  - This paper analysis the cause's dynamically loaded screws failure, using the structural analysis of mechanical properties and numerical simulation. The comparison with the new unbroken screws, which were not in use, has been done to determine the condition of the broken (dynamically loaded) ones. Analysis was performed, according to the following test methods and activities: non-destructive testing, visual inspection, radiographic testing, chemical analysis of screws sample materials, mechanical properties of screws' materials. Structure analysis of screws materials: Testing macrostructure (light optical microscope, SEM-EDS) examination of the microstructure (light optical microscope, SEM-EDS), fractographic examination. Numerical simulation of the stress state of the dynamically loaded screws was done in CATIA software package, and it was identical to the bolt loads, during service exploitation. The results between numerical simulation and structural analysis were quite coinciding - the difference is about 8-10%, which is pretty good for these types of experiments. Such an overlap, says that the stress value at the very screws is reliable and give us a true picture of loadings. Structural mechanical tests have shown a very pronounced effect of dynamic loads, that large shear stress shows also as a good agreement, where between the stresses, obtained by numerical simulation and structural mechanical testing. Analysing the results, obtained by numerical simulation and structural mechanical testing were performed with the redistribution of critical stresses, and proposal for the structure optimization. The comparative analysis methods have been provided the precise prediction of fracture appearance and made possible to define the preventive measures.
PB  - Trans Tech Publications Ltd, Durnten-Zurich
T2  - Structural Integrity of Welded Structures
T1  - Determination and analysis of the dynamic loaded screws by structural analysis, fractography and numerical simulation
EP  - 98
SP  - 87
VL  - 814
DO  - 10.4028/www.scientific.net/AMR.814.87
ER  - 

@article{
author = "Kutin, Marina and Prokolab, Milan and Ristić, Marko and Alil, Ana and Gligorijević, Bojan",
year = "2013",
abstract = "This paper analysis the cause's dynamically loaded screws failure, using the structural analysis of mechanical properties and numerical simulation. The comparison with the new unbroken screws, which were not in use, has been done to determine the condition of the broken (dynamically loaded) ones. Analysis was performed, according to the following test methods and activities: non-destructive testing, visual inspection, radiographic testing, chemical analysis of screws sample materials, mechanical properties of screws' materials. Structure analysis of screws materials: Testing macrostructure (light optical microscope, SEM-EDS) examination of the microstructure (light optical microscope, SEM-EDS), fractographic examination. Numerical simulation of the stress state of the dynamically loaded screws was done in CATIA software package, and it was identical to the bolt loads, during service exploitation. The results between numerical simulation and structural analysis were quite coinciding - the difference is about 8-10%, which is pretty good for these types of experiments. Such an overlap, says that the stress value at the very screws is reliable and give us a true picture of loadings. Structural mechanical tests have shown a very pronounced effect of dynamic loads, that large shear stress shows also as a good agreement, where between the stresses, obtained by numerical simulation and structural mechanical testing. Analysing the results, obtained by numerical simulation and structural mechanical testing were performed with the redistribution of critical stresses, and proposal for the structure optimization. The comparative analysis methods have been provided the precise prediction of fracture appearance and made possible to define the preventive measures.",
publisher = "Trans Tech Publications Ltd, Durnten-Zurich",
journal = "Structural Integrity of Welded Structures",
title = "Determination and analysis of the dynamic loaded screws by structural analysis, fractography and numerical simulation",
pages = "98-87",
volume = "814",
doi = "10.4028/www.scientific.net/AMR.814.87"
}

Kutin, M., Prokolab, M., Ristić, M., Alil, A.,& Gligorijević, B.. (2013). Determination and analysis of the dynamic loaded screws by structural analysis, fractography and numerical simulation. in Structural Integrity of Welded Structures
Trans Tech Publications Ltd, Durnten-Zurich., 814, 87-98.
https://doi.org/10.4028/www.scientific.net/AMR.814.87

Kutin M, Prokolab M, Ristić M, Alil A, Gligorijević B. Determination and analysis of the dynamic loaded screws by structural analysis, fractography and numerical simulation. in Structural Integrity of Welded Structures. 2013;814:87-98.
doi:10.4028/www.scientific.net/AMR.814.87 .

Kutin, Marina, Prokolab, Milan, Ristić, Marko, Alil, Ana, Gligorijević, Bojan, "Determination and analysis of the dynamic loaded screws by structural analysis, fractography and numerical simulation" in Structural Integrity of Welded Structures, 814 (2013):87-98,
https://doi.org/10.4028/www.scientific.net/AMR.814.87 . .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Alil, Ana
AU  - Milutinović, Zlatan R.
AU  - Odanović, Zoran
AU  - Gligorijević, Bojan
AU  - Katavić, Boris T.
PY  - 2011
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1937
AB  - The sensitization degree of austenitic stainless steel welded joints was investigated by electrochemical methods of the double loop electrochemical potentiokinetic reactivation (DL EPR) in H(2)SO(4) + KSCN solution, and by the measurement of corrosion potential of the steel in the drop of the solution of HNO(3) + FeCl(3) + HCl. The welded joints were tested by X-ray radiographic method in order to check the presence of the weld defects. The grain sizes of the base metal and the welded joints were determined by optical microscopy. Good agreement between the results obtained by different electrochemical methods was obtained. The heat-affected zone (HAZ) of the austenitic stainless steel welded joints has shown a significant degree of sensitization. The double loop electrochemical potentiokinetic method gave quantitative evidence about the susceptibility of stainless steel to intergranular corrosion.
PB  - Savez hemijskih inženjera, Beograd
T2  - Hemijska industrija
T1  - Application of electrochemical methods for the investigation of intergranular corrosion of welded joint of austenitic stainless steel 19cr-9ni
EP  - 186
IS  - 2
SP  - 179
VL  - 65
DO  - 10.2298/HEMIND101122005J
ER  - 

@article{
author = "Jegdić, Bore and Alil, Ana and Milutinović, Zlatan R. and Odanović, Zoran and Gligorijević, Bojan and Katavić, Boris T.",
year = "2011",
abstract = "The sensitization degree of austenitic stainless steel welded joints was investigated by electrochemical methods of the double loop electrochemical potentiokinetic reactivation (DL EPR) in H(2)SO(4) + KSCN solution, and by the measurement of corrosion potential of the steel in the drop of the solution of HNO(3) + FeCl(3) + HCl. The welded joints were tested by X-ray radiographic method in order to check the presence of the weld defects. The grain sizes of the base metal and the welded joints were determined by optical microscopy. Good agreement between the results obtained by different electrochemical methods was obtained. The heat-affected zone (HAZ) of the austenitic stainless steel welded joints has shown a significant degree of sensitization. The double loop electrochemical potentiokinetic method gave quantitative evidence about the susceptibility of stainless steel to intergranular corrosion.",
publisher = "Savez hemijskih inženjera, Beograd",
journal = "Hemijska industrija",
title = "Application of electrochemical methods for the investigation of intergranular corrosion of welded joint of austenitic stainless steel 19cr-9ni",
pages = "186-179",
number = "2",
volume = "65",
doi = "10.2298/HEMIND101122005J"
}

Jegdić, B., Alil, A., Milutinović, Z. R., Odanović, Z., Gligorijević, B.,& Katavić, B. T.. (2011). Application of electrochemical methods for the investigation of intergranular corrosion of welded joint of austenitic stainless steel 19cr-9ni. in Hemijska industrija
Savez hemijskih inženjera, Beograd., 65(2), 179-186.
https://doi.org/10.2298/HEMIND101122005J

Jegdić B, Alil A, Milutinović ZR, Odanović Z, Gligorijević B, Katavić BT. Application of electrochemical methods for the investigation of intergranular corrosion of welded joint of austenitic stainless steel 19cr-9ni. in Hemijska industrija. 2011;65(2):179-186.
doi:10.2298/HEMIND101122005J .

Jegdić, Bore, Alil, Ana, Milutinović, Zlatan R., Odanović, Zoran, Gligorijević, Bojan, Katavić, Boris T., "Application of electrochemical methods for the investigation of intergranular corrosion of welded joint of austenitic stainless steel 19cr-9ni" in Hemijska industrija, 65, no. 2 (2011):179-186,
https://doi.org/10.2298/HEMIND101122005J . .

TY  - JOUR
AU  - Gligorijević, Bojan
AU  - Schmidt, Harald
AU  - Radović, Nenad
AU  - Davidović, Milorad
AU  - Kutin, Marina
AU  - Janićijević, Aco
PY  - 2010
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1686
AB  - Amorphous polymer-derived Si-C-N ceramics can be doped with different elements (Al, B etc.) through various pre-ceramic polymer routes. Thus, controlling of the high temperature oxidation resistance can be achieved on an atomic level. An important factor for silica layer growth is oxygen diffusion in protective thermally grown layers. In order to get insight of the oxygen diffusion mechanism, analysis should include both, bulk and short-circuit diffusion. XRD measurements of oxidized Si-C-N and SiC revealed the possibility that oxide layers were fully crystallized and are composed of nano-sized cristobalite-like grains. Secondary ion mass spectrometry depth profile analysis after (18)O(2)-(16)O(2) isotope exchange experiments on oxidized SiC indicated that short-circuit diffusion is probably grain boundary diffusion of molecular oxygen.
PB  - World Scientific Publ Co Pte Ltd, Singapore
T2  - International Journal of Modern Physics B
T1  - Short-circuit oxygen diffusion in thermally grown silica layer
EP  - 694
IS  - 6-7
SP  - 682
VL  - 24
DO  - 10.1142/S0217979210064307
ER  - 

@article{
author = "Gligorijević, Bojan and Schmidt, Harald and Radović, Nenad and Davidović, Milorad and Kutin, Marina and Janićijević, Aco",
year = "2010",
abstract = "Amorphous polymer-derived Si-C-N ceramics can be doped with different elements (Al, B etc.) through various pre-ceramic polymer routes. Thus, controlling of the high temperature oxidation resistance can be achieved on an atomic level. An important factor for silica layer growth is oxygen diffusion in protective thermally grown layers. In order to get insight of the oxygen diffusion mechanism, analysis should include both, bulk and short-circuit diffusion. XRD measurements of oxidized Si-C-N and SiC revealed the possibility that oxide layers were fully crystallized and are composed of nano-sized cristobalite-like grains. Secondary ion mass spectrometry depth profile analysis after (18)O(2)-(16)O(2) isotope exchange experiments on oxidized SiC indicated that short-circuit diffusion is probably grain boundary diffusion of molecular oxygen.",
publisher = "World Scientific Publ Co Pte Ltd, Singapore",
journal = "International Journal of Modern Physics B",
title = "Short-circuit oxygen diffusion in thermally grown silica layer",
pages = "694-682",
number = "6-7",
volume = "24",
doi = "10.1142/S0217979210064307"
}

Gligorijević, B., Schmidt, H., Radović, N., Davidović, M., Kutin, M.,& Janićijević, A.. (2010). Short-circuit oxygen diffusion in thermally grown silica layer. in International Journal of Modern Physics B
World Scientific Publ Co Pte Ltd, Singapore., 24(6-7), 682-694.
https://doi.org/10.1142/S0217979210064307

Gligorijević B, Schmidt H, Radović N, Davidović M, Kutin M, Janićijević A. Short-circuit oxygen diffusion in thermally grown silica layer. in International Journal of Modern Physics B. 2010;24(6-7):682-694.
doi:10.1142/S0217979210064307 .

Gligorijević, Bojan, Schmidt, Harald, Radović, Nenad, Davidović, Milorad, Kutin, Marina, Janićijević, Aco, "Short-circuit oxygen diffusion in thermally grown silica layer" in International Journal of Modern Physics B, 24, no. 6-7 (2010):682-694,
https://doi.org/10.1142/S0217979210064307 . .

TY  - JOUR
AU  - Mijin, Dušan
AU  - Bugarski, Branko
AU  - Gligorijević, Bojan
AU  - Milivojević, Milan
PY  - 2004
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/617
PB  - Association of Chemical Engineers of Serbia
T2  - Hemijska industrija
T1  - Preliminary studies on controlled release of acetylsalycilic acid from membrane module
EP  - 38
IS  - 6a
SP  - 36
VL  - 58
UR  - https://hdl.handle.net/21.15107/rcub_technorep_617
ER  - 

@article{
author = "Mijin, Dušan and Bugarski, Branko and Gligorijević, Bojan and Milivojević, Milan",
year = "2004",
publisher = "Association of Chemical Engineers of Serbia",
journal = "Hemijska industrija",
title = "Preliminary studies on controlled release of acetylsalycilic acid from membrane module",
pages = "38-36",
number = "6a",
volume = "58",
url = "https://hdl.handle.net/21.15107/rcub_technorep_617"
}

Mijin, D., Bugarski, B., Gligorijević, B.,& Milivojević, M.. (2004). Preliminary studies on controlled release of acetylsalycilic acid from membrane module. in Hemijska industrija
Association of Chemical Engineers of Serbia., 58(6a), 36-38.
https://hdl.handle.net/21.15107/rcub_technorep_617

Mijin D, Bugarski B, Gligorijević B, Milivojević M. Preliminary studies on controlled release of acetylsalycilic acid from membrane module. in Hemijska industrija. 2004;58(6a):36-38.
https://hdl.handle.net/21.15107/rcub_technorep_617 .

Mijin, Dušan, Bugarski, Branko, Gligorijević, Bojan, Milivojević, Milan, "Preliminary studies on controlled release of acetylsalycilic acid from membrane module" in Hemijska industrija, 58, no. 6a (2004):36-38,
https://hdl.handle.net/21.15107/rcub_technorep_617 .