Претраживање
Приказ резултата 1-10 од 3241
Electrochemical and sorption characteristics of metacryloxypropyltrimethoxysilane coatings / Elektrohemijske i sorpcione karakteristike prevlaka metakriloksipropiltrimetoksisilana
(Engineering Society for Corrosion, Belgrade, Serbia, 2008)
The aim of this work was to investigate the influence of deposition parameters (silane solution concentration, deposition time, curing time) on electrochemical and sorption characteristics of metacryloxypropyltrimethoxysilane ...
Premazi na bazi cirkona sa primenom u Lost Foam procesu livenja / Zircon-based coating for the applications in Lost Foam casting process
(Savez hemijskih inženjera, Beograd, 2012)
U ovom radu je istraživana mogućnost dobijanja novih vatrostalnih premaza na bazi cirkona koji bi imali primenu u livarstvu. Optimizacija sastava premaza kontrolisana reološkim svojstvima postignuta je primenom različitih ...
Preparation and characterization of two types of covalently immobilized amyloglucosidase / Dobijanje i karakterizacija dva tipa imobilizovane amiloglukozidaze
(Serbian Chemical Soc, Belgrade, 2005)
Amyloglucosidase from A. niger was covalently immobilized onto poly(GMA-co-EGDMA) by the glutaraldehyde and periodate method. The immobilization of amyloglucosidase after periodate oxidation gave a preparate with the highest ...
The influence of electrochemically deposited zinc alloys on steel on the protective properties of cathaporetic epoxy coatings / Uticaj elektrohemijski taloženih legura cinka na čeliku na zaštitna svojstva epoksidne kataforetske prevlake
(Engineering Society for Corrosion, Belgrade, Serbia, 2005)
Prior to cathaporetic epoxy coating deposition steel surface was modified by chemical deposition of hot dip galvanized steel and by electrochemical deposition of zinc alloys with iron group of elements (Ni, Co and Fe). The ...
Technological characterization of lactic acid bacteria isolated from Radan’s cheese / Karakterizacija tehnoloških osobina bakterija mlečne kiseline izolovanih iz sira sa planine Radan
(Univerzitet u Nišu - Tehnološki fakultet, Leskovac, 2005)
Isolation of lactic acid bacteria from artisanal dairy products is base for selection of new strains with properties which are important for their industrial application. In this work, characterization of 69 strains isolated ...
Electrochemical deposition and characterization of Zn-Fe alloys / Elektrohemijsko taloženje i karakterizacija Zn-Fe legura
(Serbian Chemical Society, Belgrade, 2004)
Zn–Fe alloy electrochemically deposited on steel under various deposition conditions were investigated using anodic linear sweep voltammetry (ALSV) and X-ray diffraction (XRD) analysis for phase structure determination, ...
Calculation of elasticity modulus of particulate composite biomaterials using finite element method / Numeričko određivanje modula elastičnosti čestično kompozitnih biomaterijala primenom metode konačnih elemenata
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2003)
The influence of particle geometry, volume fraction and particle distribution on the modulus of elasticity of a hydroxyapatite (HAp) particulate reinforced polymer (poly -L-lactide) matrix composite biomaterial was ...
Korozija metala - šta je to?
(Engineering Society for Corrosion, Belgrade, Serbia, 2004)
Korozija materijala je opšte poznat i prihvaćen izraz, ali da li se baš tačno zna šta je korozija? Pod pojmom korozija materijala se podrazumeva svako neželjeno razaranje materijala kao posledice delovanja spoljne sredine. ...
Significance of cracks in the heat-affected-zone of steels for elevated temperature application / Značaj prslina u zoni uticaja toplote čelika za povišene temperature
(Society for Structural Integrity and Life, Institute for Material Testing, 2008)
Damage and failure of welded joints are classified according to the crack position. Type IV cracking occurs in welded joints in creep-resistant steels, due to enhanced rate of creep void formation in the presence of coarse ...
Erosive wear resistance of silicon carbide-cordierite ceramics: influence of the cordierite content
(Inst Za Kovinske Materiale I In Tehnologie, Ljubjana, 2015)
A cordierite/SiC composite was created in situ with reactive sintering at 1250 degrees C and 1300 degrees C. The cordierite precursor was made from commercially available spinel, alumina and quartz and was mixed with the ...