Претраживање
Приказ резултата 161-170 од 178
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Influence of encastering on thin-walled cantilever beams with u and z profiles on the magnitude of equivalent stress and deformation
(Society for Structural Integrity and Life, Institute for Material Testing, 2019)
The purpose of this work is to present analytical and numerical determination of equivalent stress and deformation of open section thin-walled U and Z cantilever beams loaded with torsion. This work can be divided into two ...
An overview of application of micromechanical models in ductile fracture analysis of welded joints
(Srpsko društvo za mehaniku, Beograd, 2020)
Fracture of welded joints has been an important research and industrial topic for a long time, having in mind the key role of welded joints in ensuring the safe operation and integrity of welded structures. This work ...
Production of sub-micro sized silver particles by chemical reduction method in an environmentally-friendly manner
(Savez inženjera metalurgije Srbije, Beograd, 2020)
Silver nitrate in the solution was reduced in the presence of the dispersants by ascorbic acid, and silver particles were generated. The main goal was to examine the influence of different dispersants. The purpose was to ...
Exergy concept and its implementation in the recycling of metals / Eksergijski koncept i njegova primena u recikliranju metala
(Engineering Society for Corrosion, Belgrade, Serbia, 2017)
Modern industrial product design implies presence of many different materials. Consequently, in the recycling process, shredding and separation procedures are applied. However, all materials cannot be completely separated; ...
Exploitation properties of ni-pd/al2o3 catalyst supported on ceramic foam
(Savez inženjera metalurgije Srbije, Beograd, 2015)
The goal of this research was to examine exploitation properties of Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam in the dry methane reforming. The catalyst was prepared by using aerosol method. Chloride precursors ...
Complex sulphide-barite ore leaching in ferric chloride solution
(Association of Metallurgical Engineers of Serbia, 2016)
The results of research on the leaching process of complex sulphide-barite ore were presented in this paper. The leaching process was carried out in a laboratory autoclave by ferric chloride solution. Considering that those ...
Effect of the pH of artificial saliva on ion release from commercially pure titanium / Uticaj pH vrednosti veštačke pljuvačke na otpuštanje jona iz komercijalno čistog titana
(Faculty of Technology, Novi Sad, 2013)
Due to their excellent characteristics, such as chemical inertness, mechanical resistance, low Young's modulus, high corrosion resistance, and outstanding biocompatibility, titanium and its alloys are the most used metallic ...
New types of protective coatings and development of test methods / Nove vrste zaštitnih premaza i razvoj metoda ispitivanja
(Society for Structural Integrity and Life (DIVK), 2023)
The paper presents the results of synthesis and characterisation of refractory coatings based on various fillers
intended for the protection of metallic structures. Refractory
fillers applied are based on mullite, ...
Strength design calculation of a horizontal pressure vessel / Kontrolni proračun čvrstoće horizontalne posude pod pritiskom
(Society for Structural Integrity and Life, Institute for Material Testing, 2013)
Standards SRPS M.E2.250-262 for calculation of pres-sure vessels have been replaced by SRPS EN 13445-3. This means that calculations of new equipment and check calculations of equipment in service are subjected to ordinance ...