Претраживање
Приказ резултата 1-10 од 70
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (hsla) steel on low cycle fatigue
(Croatian Metallurgical Soc, Zagreb, 2014)
High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of ...
High strength thermoresponsive semi-IPN hydrogels reinforced with nanoclays
(Wiley Periodicals, Inc., 2012)
Two series of nanoclay reinforced, thermoresponsive hydrogels were prepared, one based on poly(N-isopropylacrylamide) (PNIPA) and the other on semi-interpenetrating networks containing PNIPA and poly(N-vinyl pyrrolidone) ...
Effect of hydroxyapatite spheres, whiskers, and nanoparticles on mechanical properties of a model BisGMA/TEGDMA composite initially and after storage
(Wiley-Blackwell, Hoboken, 2013)
This study investigated the effect of shape, size, and surface modification of hydroxyapatite (HAP) fillers on the degree of conversion (DC) and mechanical properties of a model BisGMA/TEGDMA composite initially and after ...
Effect of surface modified TiO2 nanoparticles on thermal, barrier and mechanical properties of long oil alkyd resin-based coatings
(Budapest Univ Technol & Econ, Budapest, 2015)
Novel soy alkyd-based nanocomposites (NCs) were prepared using TiO2 nanoparticles (NPs) surface modified with different gallates, and for the first time with imine obtained from 3,4-dihydroxybenzaldehyde and oleylamine ...
Identification of low cycle fatigue parameters of high strength low-alloy (hsla) steel at room temperature
(Croatian Metallurgical Soc, Zagreb, 2014)
Low cycle fatigue test was performed in ambient atmosphere at room temperature. cycle loading of material, in case of High strength low-alloy steel, entails modifications of its properties and in this paper is therefore ...
An Investigation into Mechanical Properties and Printability of Potential Substrates for Inkjet Printing of Orodispersible Films
(Pharmaceutics, 2021)
Inkjet printing is novel approach in drug manufacturing that enables dispensing precise volumes of ink onto substrates. Optimal substrate properties including suitable mechanical characteristic are recognized as crucial ...
Smart hydrogels based on itaconic acid for biomedical application / Inteligentni hidrogelovi na bazi itakonske kiseline za biomedicinsku primenu
(Association of Chemical Engineers of Serbia, 2009)
pH and temperature sensitive hydrogels, based on 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA) copolymers, were prepared by gamma irradiation and characterized in order to examine their potential use in biomedical ...
Izrada termoplastičnih kompozitnih cevi metodom namotavanja, II : rezultati eksperimenta / Fabrication of Thermoplastic Composite Pipes Using Tape Winding Process, II : Experimental Results
(Društvo inženjera plastičara i gumara, 2005)
U ovom delu rada su prikazani rezultati eksperimenata na aparaturi opisanoj u prvom delu rada. Na osnovu eksperimentalnih merenja utvrđen je uticaj uslova dobijanja kompozitne cevi, odnosno procesnih parametara: brzine ...
Denture composite reinforced with short polyethylene terephthalate fibers
(John Wiley and Sons Inc., 2022)
Polymer matrix composite materials have found application in dentistry because of good mechanical properties, aesthetic, easy processing, and possibilities of the repair. Acrylates are materials used to make and repair ...
Microstructure and properties of silver based cadmium free electrical contact materials
(University of Belgrade, Technical Faculty, Bor, 2007)
The presented work covers part of experimental results of simultaneous study of microstructure, density, hardness and electrical conductivity of sintered electrical contact materials based of Ag- SnO2 with 8, 10 and 12 ...