Search
Now showing items 1-10 of 19
Manganese electrodeposition from urea-rich electrolyte
(Soc Chemists Technologists Madeconia, Skopje, 2015)
Pure manganese coatings were prepared on the steel (AISI 4340) electrode by a non-conventional electrodeposition method, in the presence of 8 mol dm(-3) of urea as a plating additive. The influence of urea on the ...
Synergetic effect of additives on the hardness and adhesion of thin electrodeposited copper films
(Faculty of Technical Sciences in Cacak, 2017)
Thin copper films were electrodeposited on a polycrystalline cold rolled copper substrate. The composition of the laboratory-made copper sulphate electrolyte was changed by the addition of various additives. The influence ...
The importance of using hydrogen evolution inhibitor during the Zn and Zn-Mn electrodeposition from ethaline
(Srpsko hemijsko društvo, Beograd, 2019)
Cyclic voltammetry was used for the characterization of zinc electro-deposition on steel from ethaline deep eutectic solution (1:2 choline chloride:ethylene glycol). The influence of 4-hydroxy-benzaldehyde (HBA) as an ...
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Inženjersko društvo za koroziju, Beograd, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Engineering Society for Corrosion, Belgrade, Serbia, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
Microindentation hardness testing of different composite systems with thin electrodeposited nickel and copper films
(Belgrade : Military Technical Institute, 2012)
Thin Ni and Cu films with fine-grained structures have been electrodeposited from self-made sulphamate-based and sulphate-based electrolytes, respectively. DC electrodeposition of Ni films was performed on single crystal ...
Microstructure and corrosion behaviour of Zn-Co alloys deposited from three different plating baths / Mikrostruktura i koroziono ponašanje Zn-Co legura taloženih iz sulfatnog i hloridnih rastvora
(Serbian Chemical Society, Belgrade, 2011)
The effects of plating baths of different composition on the micro- structure and corrosion stability of Zn-Co alloy coatings were studied. Zn-Co alloys with the same Co content were deposited from chloride plating baths ...
Formation of Disperse Silver Deposits by the Electrodeposition Processes at High Overpotentials
(Esg, Belgrade, 2012)
In this study, electrodeposition of silver from nitrate solution at the high overpotentials was analyzed. Morphologies of silver deposits obtained at the different overpotentials and with the different electrodeposition ...
Hardness response and adhesion of thin copper films on alloy substrates
(Belgrade: ETRAN – Society for electronics, telecommunication, computing, automatics and nuclear engineering, 2017)
Microhardness test is the most commonly used method for assessing the mechanical properties of thin films.This testing method uses controlled contact at a single point of an indenter and chosen material which induces the ...