Pretraživanje
Prikaz rezultata 31-40 od 62
Electrophoretic deposition of thin alumina films from water suspension
(Elsevier, Amsterdam, 2002)
Alumina water suspensions have been prepared for thin alumina film deposition on steel. The type and quantity of deflocculant have been determined using zeta potential and viscosimetric measurements. The deposition was ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Engineering Society for Corrosion, Belgrade, Serbia, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
Microstructure and corrosion behaviour of Zn-Co alloys deposited from three different plating baths / Mikrostruktura i koroziono ponašanje Zn-Co legura taloženih iz sulfatnog i hloridnih rastvora
(Serbian Chemical Society, Belgrade, 2011)
The effects of plating baths of different composition on the micro- structure and corrosion stability of Zn-Co alloy coatings were studied. Zn-Co alloys with the same Co content were deposited from chloride plating baths ...
Formation of Disperse Silver Deposits by the Electrodeposition Processes at High Overpotentials
(Esg, Belgrade, 2012)
In this study, electrodeposition of silver from nitrate solution at the high overpotentials was analyzed. Morphologies of silver deposits obtained at the different overpotentials and with the different electrodeposition ...
The study of Zn-Co alloy coatings electrochemically deposited by pulse current / Ispitivanje prevlaka Zn-Co legura dobijenih pulsirajućom strujom
(Association of Chemical Engineers of Serbia, 2012)
The electrochemical deposition by pulse current of Zn-Co alloy coatings on steel was examined, with the aim to find out whether pulse plating could produce alloys that could offer a better corrosion protection. The influence ...
Synergetic effect of additives on the hardness and adhesion of thin electrodeposited copper films
(Faculty of Technical Sciences in Cacak, 2017)
Thin copper films were electrodeposited on a polycrystalline cold rolled copper substrate. The composition of the laboratory-made copper sulphate electrolyte was changed by the addition of various additives. The influence ...
Structural, Mechanical and Electrical Characteristics of Copper Coatings Obtained by Various Electrodeposition Processes
(Electronics, 2022)
Mechanical (hardness and adhesion) and electrical (sheet resistance) characteristics of electrolytically produced copper coatings have been investigated. Morphologies of Cu coatings produced galvanostatically at two current ...
Manganese electrodeposition from urea-rich electrolyte
(Soc Chemists Technologists Madeconia, Skopje, 2015)
Pure manganese coatings were prepared on the steel (AISI 4340) electrode by a non-conventional electrodeposition method, in the presence of 8 mol dm(-3) of urea as a plating additive. The influence of urea on the ...
Ceria Particles as Efficient Dopant in the Electrodeposition of Zn-Co-CeO2 Composite Coatings with Enhanced Corrosion Resistance: The Effect of Current Density and Particle Concentration
(Molecules, 2021)
Novel Zn-Co-CeO2 protective composite coatings were deposited successfully from chloride plating solutions. Two different types of ceria sources were used and compared: commercial ceria powder and home-made ceria sol. ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Inženjersko društvo za koroziju, Beograd, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...